| 例文 |
current zeroの部分一致の例文一覧と使い方
該当件数 : 1104件
On the contrary, when the current IAC becomes substantially zero and it is determined that the voltage VAC is normal, i.e. it is an AC voltage corresponding to the power supply outside the vehicle (YES in S30), it is identified that the abnormal conditions occur in the charging circuit inside the vehicle (S70).例文帳に追加
一方、電流IACが略零となり、かつ、電圧VACが正常すなわち車両外部の電源に応じた交流電圧であると判定されると(S30にてYES)、車両内部の充電経路において異常が発生したものと特定される(S70)。 - 特許庁
The class AB amplifier is provided with: an input amplifying part (10) for amplifying differential input voltage; an output amplifying part (20) for amplifying the current output of the input amplifying part 10; and a zero gain compensating part (40) for controlling the gain of the input amplifying part (10) in accordance with the differential input voltage.例文帳に追加
AB級増幅器は、差動入力電圧を増幅する入力増幅部(10)、入力増幅部10の電流出力を増幅する出力増幅部(20)、差動入力電圧に応じて入力増幅部(10)のゲインを制御するゼロゲイン補償部(40)を備えている。 - 特許庁
The buffer BUF is configured so as to switch, corresponding to the control signals, an enable state wherein the differential signal corresponding to the differential signal inputted to the differential input terminal Di is outputted and a disable state wherein current consumption practically becomes zero and the differential output terminal becomes high impedance.例文帳に追加
バッファBUFは、差動入力端子Diに入力される差動信号に応じた差動信号を出力するイネーブル状態と、消費電流が実質的にゼロとなり、その差動出力端子がハイインピーダンスとなるディスエーブル状態と、が制御信号に応じて切りかえ可能に構成される。 - 特許庁
The servo IC (50) is constituted so as to set the target value to zero in shift quantity, biases the torque order corresponding to the detection value of the laser displacement meter 48 to operation/pressurization force being the operation point of the motor to set it by bias setting 52 and supplies the drive current 56 corresponding to the biased torque order to the motor 42.例文帳に追加
サーボIC(50)は、目標値をずれ量ゼロとし、バイアス設定52により、レーザ変位計48の検出値に対応するトルク指令をモータの作動点である作動加圧力にバイアスして設定し、バイアスされたトルク指令に応じた駆動電流56をモータ42に供給する。 - 特許庁
Preferably, voltage is applied between the single crystal and the crucible when the change in the weight of the single crystal shows zero and the separation of the tail part of the single crystal from the raw material molten liquid is detected by a fact that current is not passed between the single crystal and the crucible.例文帳に追加
好ましくは、単結晶の重量変化量が0となった時に単結晶とルツボとの間に電圧を印加し、前記単結晶のテール部が前記原料融液から離間したことを前記単結晶とルツボとの間に電流が流れなくなることにより検出する。 - 特許庁
To provide a transmission line protective relay that properly controls on/off of an interrupt command output from a main protective relay by identifying whether a follow current interrupting type arc horn is in operation or not, according to a value of a zero-phase voltage, and prevents unnecessary delay and output of the interrupt command.例文帳に追加
零相電圧の値に応じて続流遮断形アークホーンの動作あるいは不動作を識別することにより、主保護リレーから出力される遮断指令の活殺を適切に制御し、遮断指令の不要な遅延や出力を防ぐようにした送電線保護継電装置を提供する。 - 特許庁
A signal processor 12 calculates the currents flowing through the conductors 5U, 5V, 5W, based on output signals from the coreless current sensors 11A, 11B and the previously-obtained coefficients by utilizing a fact that the sum of the currents flowing through the conductors 5U, 5V, 5W is zero.例文帳に追加
信号処理装置12は、導体5U、5V、5Wを介して流れる電流の総和がゼロであることを利用して、コアレス電流センサ11A、11Bの出力信号および先に取得した係数に基づいて、各導体5U、5V、5Wを介して流れる電流を算出する。 - 特許庁
To provide a vehicle-mounted navigation apparatus capable of reducing the effects of zero-point drift of a 3D gyrosensor when a vehicle comes close to a slope road and determining the current position of the vehicle without any delays in determination on the entrance to the slope road nor confusing users.例文帳に追加
車両が勾配路に差し掛かった際に、3Dジャイロセンサの0点ドリフトとの影響を軽減し、勾配路への進入における判定が遅れずにユーザを混乱させることなく車両の現在位置を判定することができる車両用ナビゲーション装置を提供する。 - 特許庁
A field magnetic flux control unit 2-1 gets a primary magnetic flux command ϕ1*d by multiplying a field current command il*d by an estimate value L1_-HAT of primary inductance, and controls the magnetic flux so that a deviation between a primary magnetic flux command ϕ1*d and an actual magnetic flux may be zero.例文帳に追加
界磁磁束制御部2−1は、界磁電流指令il*dに1次側インダクタンスの推定値L1_HATを乗算して1次磁束指令φ1*dを得て、1次磁束指令φ1*dと実際の磁束との間の偏差がゼロになるように磁束制御する。 - 特許庁
The signal level of the signal 13 is determined by the signal 16, and about the block 20 that is made not to operate, power consumption due to a leakage current when a MOS transistor constituting the block 20 is off can be zero by not feeding the power supply VDD2.例文帳に追加
第一の制御信号16によって内部信号13の信号レベルが確定し、動作させない機能ブロック20については第二の電源VDD2を供給しないことにより、機能ブロック20を構成するMOSトランジスタのオフ時のリーク電流による消費電力をゼロにすることができる。 - 特許庁
The volume setting section 16 changes the volume by a predetermined range each time the timing signal Stm reaches the predetermined level at a transition timing that the zero-cross detection signal Szc reaches the predetermined timing right after that, and repeats it to shift the volume from the current value to the target value.例文帳に追加
ボリューム設定部16は、タイミング信号Stmが所定レベルとなるごとに、その直後にゼロクロス検出信号Szcが所定レベルとなる遷移タイミングにて、ボリュームを所定幅だけ変化させ、これを繰り返すことにより、現在値から目標値へのボリューム遷移を実行する。 - 特許庁
To determine the time when the mechanical feedback to the motor 26 causes no problem, while the selected switching device is periodically switched, needed to sample the current in at least one phase of the motor 26, preferably an average zero voltage vector is maintained.例文帳に追加
本発明は、モータ(26)への機械的フィードバックが問題とならなくなった時期を決定するためにモータ(26)の少なくとも一つの相における電流をサンプリングするのに必要な選択された切換装置を周期的に切り換える一方で、好ましくは、平均ゼロ電圧ベクトルも維持する。 - 特許庁
A DC power supply source having a power storage system with a capacity to process the current flowing into or out of the inverter is inserted in series to the ground side of the input of the inverter and the output voltage thereof is continuously controlled from zero to be added to the trolley voltage, which is then applied to the inverter.例文帳に追加
インバータの入力の接地側に、インバータに流入もしくは流出する電流を処理可能な容量の蓄電装置を有する直流電圧源を直列に挿入し、この出力電圧をゼロから連続的に制御して架線電圧に加算してインバータに印加する。 - 特許庁
The serial multiple matrix converter includes a voltage correction value storage section (141) for storing a voltage command as a voltage correction value when a current command value is made zero and a correction voltage command generating section (140) for generating a correction voltage command by adding the voltage command and the voltage correction value and commanding the correction voltage command to a single phase matrix converter.例文帳に追加
電流指令値を零にしたときの電圧指令を電圧補正値として記憶する電圧補正値記憶部(141)と、電圧指令と電圧補正値を加算して補正電圧指令を生成し単相マトリクスコンバータに指令する補正電圧指令生成部(140)とを備えた。 - 特許庁
The magnetic field cancellation system comprises a magnetic core having an air gap, a coil wound around the magnetic core, a control sensor arranged in the air gap and measuring a magnetic field, and a controller which controls a current to be fed to the coil so that the magnitude of a magnetic field measured by the sensor approaches zero.例文帳に追加
磁場キャンセルシステムは、エアーギャップを有する磁芯と、前記磁芯に巻きつけられたコイルと、前記エアーギャップ内に配置され、磁場を測定する制御用センサーと、前記センサーにより測定される磁場の大きさがゼロに近づくように、前記コイルに流す電流を制御する制御装置とを有する。 - 特許庁
The three power source lines for supplying the operating power are coupled by a coupling circuit 10 which delta-connects the coupling lines 10a, 10b and 10c interposed with resistors R1, R2 and R3, and the coupling lines 10a, 10b and 10c are inserted into the zero-phase current transformer 2.例文帳に追加
そして、この動作電力を供給する3本の電源線路同士を抵抗R1,R2,R3介在させた連結線10a,10b、10cをΔ結線した連結回路10で連結し、各連結線10a,10b、10cを零相変流器2に挿通した。 - 特許庁
Then, a mode is set so that the power consumption of a main circuit section comprised in the semiconductor device becomes zero or substantially a constant and, thereafter, the elements 121b, 122b to be measured are conducted sequentially to sequentially measure the power supply current, which is made to flow through the semiconductor device under this condition.例文帳に追加
そして、半導体装置に含まれる主回路部の消費電力が実質的にゼロ又はほぼ一定となるようモード設定した後、被測定素子121b,122b・・・に順次通電させ、この状態で半導体装置に流れる電源電流を順次計測する。 - 特許庁
The zero-phase current transformer has: primary conductors 12 where balanced currents flow; and a detection unit 20 having an annular core 22 that the primary conductors 12 penetrates and a secondary winding 24 wound around the annular core 22, wherein an annular choke core 30 that the primary conductors 12 penetrate is provided integrally with the detection unit 20.例文帳に追加
平衡電流が流れる一次導体12と、一次導体12が貫通する環状コア22と、環状コア22に巻回される二次巻線24と、を備える検知部20を有し、一次導体12が貫通する環状のチョークコア30を検知部20と一体化して設ける。 - 特許庁
An operation means 23a-3 adds the voltage drop caused by concentration polarization calculated based on the difference of the terminal voltages at the point where the discharge current is zero in the first and second approximate expressions and calculates the voltage drop caused by factors other than the concentration polarization separately from that caused by the concentration polarization.例文帳に追加
演算手段23a−3が、第1及び第2の近似式の放電電流0である点における端子電圧の差に基づいて算出した濃度分極による電圧降下を加算して濃度分極以外による電圧降下を濃度分極によるものと分離して算出する。 - 特許庁
In a learning processing section 60, command currents Idc and Iqc are set so that a current flowing through a U phase reaches zero, and the Idc and Iqc are converted into command voltages Vdc and Vqc on a dq axis from a voltage equation and output to a three-phase conversion section 52 through selectors S1 and S2.例文帳に追加
学習処理部60では、U相を流れる電流がゼロとなるように、指令電流Idc,Iqcを設定し、電圧方程式からこれをdq軸上の指令電圧Vdc、Vqcに変換した後、セレクタS1,S2を介して3相変換部52に出力する。 - 特許庁
From an actual value of tension when the winder where the long material 1 has a travel speed of zero is activated via a torque command value, a second new take-up diameter computing element calculates a new take-up diameter, to which the current take-up diameter is updated.例文帳に追加
長尺材1の走行速度が零の状態で巻取り機へ別途のトルク指令値を与えて運転させたときに得られる張力実際値から第2新規巻取り径演算器40が新規の巻取り径を演算し、それまでの巻取り径をこの新規巻取り径演算値に書き換える。 - 特許庁
A phase difference T between a zero-crossing point of a current Iu flowing in phase winding Lu of the DC motor 1 and a pulse signal Vp that is outputted from a rotational position detector 4 in the DC motor 1 is controlled directly to an optimum value in accordance with the revolutions N of the DC motor 1.例文帳に追加
直流モータ1の相巻線Luに流れる電流Iuの零クロス点と、直流モータ1における回転位置検出器4から出力されるパルス信号Vpとの位相差Tを、直流モータ1の回転数Nに応じた最適値に直接的に制御する。 - 特許庁
To solve the problem of a conventional system that a period, while the operation state of an inverter is a zero vector, becomes shorter than well-known triangular wave PWM processing, when controlling a difference between a current, which flows actually in a rotating machine, and its command into a tolerance by operating a switching element for an inverter IV.例文帳に追加
インバータIVのスイッチング素子を操作することで回転機を実際に流れる電流とその指令値との差を許容領域内に制御するに際し、インバータの操作状態をゼロベクトルとする期間が周知の三角波PWM処理と比較して短くなること。 - 特許庁
The operation direction of the electromagnet device 31 is a direction connecting the both ends of the device body 1, and the electromagnet device 31, the main contact device 8, the relay contact device 9, and the zero-phase current transformer 100 are arranged divided in four directions of the direction connecting the both ends of the device body 1 and the vertical direction.例文帳に追加
電磁石装置31の動作方向は器体1の両端を結ぶ方向であって、電磁石装置31と主接点装置8とリレー接点装置9と零相変流器100とは、器体1の両端を結ぶ方向および上下方向の四方に分けて配置されている。 - 特許庁
Thereby, a rotational angle is derived by using the stroke sensor for detecting the amount of stroke in the actuator in sensorless drive without any rotation position detectors of a rotor, and by detecting the commutation timing by the current value of the motor, torque control from a zero speed (in stop) can be performed.例文帳に追加
これにより、回転子の回転位置検出器を持たないセンサレス駆動にて、アクチュエータのストローク量を検出するストロークセンサを用いて回転角度を導出するとともに、モータの電流値によって転流タイミングを検出し、ゼロ速度(停止時)からトルク制御することができる。 - 特許庁
An adjusting circuit 32 obtains deviation between a potential of the neutral point B and an average potential of the potentials +HV, -HV, at both output ends of the single power source and adjusts a drive current to be supplied to the winding 30w of the phase W so as to reduce this deviation to zero by feeding back the deviation.例文帳に追加
調整回路32は、中性点Bの電位と、単電源の両出力端の各電位+HV,−HVの平均電位との偏差を求め、この偏差をフィードバックして、この偏差が実質的にゼロとなるように、W相の巻線30wに供給する駆動電流を調整する。 - 特許庁
When a power switch is switched on, the movement control apparatus 40 drives each articulation up to its mechanical drive limit position in both swing directions, and detects the limit positions by means of the angle sensor 45, a force sensor or a current sensor provided on the articulation, and thus carries out the zero setting of the articulation.例文帳に追加
動作制御装置40は、電源投入時に、各関節部について双方の揺動方向に機械的駆動限界位置まで駆動して、その限界位置を当該関節部に設けられた角度センサ45、力センサ又は電流センサにより検出して、当該関節部の原点出しを行なう。 - 特許庁
A slowdown time as a displacement time reducing the drive current in order to reduce the inclination of the swash plate 44c from a half to zero is divided into two fixed times, and these fixed times are changed according to brake pressure.例文帳に追加
車速が低下してサービスブレーキとポンプ作動との併用状態からサービスブレーキのみの使用状態に移行するときに、制御手段15が油圧ポンプ/モータ44の斜板44cの傾転角を、制動力の発生しない中立位置まで徐々に変化させる制御を、段階的に行う。 - 特許庁
The high-voltage ground relay is composed of an operation relay element A which operates at a set time interval after the flow of zero- phase-sequence current not smaller than a set value into a ZCT when a ground occurs in a system, and a suppressing relay element B which operates by potential of unspecified frequency and has a locking function for a relay.例文帳に追加
系統に地気発生の際、設定値以上の零相電流がZCTに流れると設定時限後に動作する動作リレー要素Aと、不特定周波数の電位で動作して継電器のロック機能をもつ抑止リレー要素Bより高圧地絡継電器を構成するもの。 - 特許庁
At a healthy commercial power supply time, a high-speed limiting current shut-off unit 3 supplies the power to a load through a dc reactor, and a standby power supply unit 4 performs a PW control so that both the effective power and the reactive power supplied to a load 9 become zero.例文帳に追加
商用電源の健全時には、高速限流遮断部3は商用電源から直流リアクトルを介して負荷に対して電力を供給し、予備電源部4は負荷9に対して供給する有効電力及び無効電力が共に零となるようにPQ制御を行う。 - 特許庁
This light receiving circuit is provided with a photodiode PD, a biasing means for making the bias voltage of the photodiode PD zero volt, a FET2 for detecting the cathode voltage of the photodiode PD, and an operational amplifier OP1 for converting current through the photodiode PD into voltage on the basis of the output of the FET.例文帳に追加
フォトダイオードPDと、前記フォトダイオードPDのバイアス電圧を零ボルトとするバイアス手段と、前記フォトダイオードPDのカソード電圧を検出するFET2と、前記FETの出力に基づき前記フォトダイオードPDを流れる電流を電圧に変換するオペアンプOP1とを具備する。 - 特許庁
When a failure is detected (Yes in step 104), the fuel cell system reads out the release end voltage preset as the initial value as an output voltage corresponding the output current zero and controls the voltage so that the output voltage of the fuel cell coincides with the release end voltage (step 107).例文帳に追加
異常が検出されると(ステップ104;YES)、燃料電池システムは、出力電流ゼロに対応する出力電圧として、予め初期値設定された開放端電圧を読み出し、燃料電池の出力電圧が開放端電圧に一致するように、電圧制御する(ステップ107)。 - 特許庁
When the feedback control is conducted, the microcomputer 1 stops updating a learning value when the transistor Tr is turned off, and also forcedly turns off the transistor Tr when the transistor Tr is not turned off and the voltage difference between the both ends of the current detection resistance R1 becomes zero.例文帳に追加
このフィードバック制御時においてマイコン1は、トランジスタTrがオフ状態のときには、学習値の更新を中止し、またトランジスタTrがオフ状態でなく、電流検出抵抗R1の両端の電圧差が0となったときには、トランジスタTrを強制的にオフ状態とする。 - 特許庁
The reflux flow quantity Qr thereby becomes a variable quantity increasing or decreasing according to the calculated value of valve driving current and therefore the reflux flow quantity Qr does not become either of zero and the maximum value as before and is adjusted to a value according to the filer inflow temperature Tf.例文帳に追加
これにより、還流量Qrは、バルブ駆動電流の算出値に応じて増減する可変量となるので、還流量Qrは、従来のようにゼロまたは最大値のいずれか一方になるのではなく、フィルタ流入温度Tfに応じた値に調節される。 - 特許庁
The detection unit 2 has at least two electric paths formed in a terminal table 2, and a plurality of annular current transformers 5 each of which contains the other electric path 7 other than at least one of the electric paths 7 and one annular zero-phase current transformer 6 which contains the electric paths 7 in a lot are arranged to be superposed in multi-stages in the terminal table 2.例文帳に追加
少なくとも2つ以上の電路が端子台2の内部に形成され、前記電路7のうち少なくとも1つを除く他の電路7を個別に包含する複数の環状の変流器5と、前記電路7を一括して包含する1つの環状の零相変流器6とが端子台2の内部に多段に重ねて配置されていることを特徴とする検出ユニット2により、課題解決を図る。 - 特許庁
The light emitting device includes layers of material formed between a first electrode and a layer containing organic compound and between the layer containing organic compound and a second electrode, (the layers of materials having electric current-voltage characteristics that exhibit a substantially point-symmetric profile with respect to zero in a graphical representation with an ordinate and an abscissa representing voltage values and current values, respectively), to have a new structure suitable for AC drive.例文帳に追加
本発明は、第1の電極と有機化合物を含む層との間と、有機化合物を含む層と第2の電極との間の両方に材料層(電流値を横軸にとり、電圧値を縦軸にとったグラフ表示においてゼロを中心としたほぼ点対称な電流−電圧特性を有する材料層)を設けて、交流駆動に適した新規な構造を有する発光素子を特徴としている。 - 特許庁
When the bus-tie circuit breaker 3 is turned 'OFF' and the simultaneous protection relay 14 operates, an input current from the bus-time current transformers 4, 5 is forcibly set to zero with a divided protection relay software process 17.例文帳に追加
母線1、2間を連絡するブスタイ回路に設けられた遮断器3の片側に母線保護用のブスタイ変流器4、5を設置し、上記母線を一括保護および分割保護方式により保護する母線保護継電装置において、ブスタイ遮断器3「切」で且つ一括保護リレーが動作14したとき、上記ブスタイ変流器4、5からの入力電流を分割保護リレーソフトウェア処理17によって強制的に零にするようにした。 - 特許庁
To provide a controller for an electric power steering device which relaxes an impact to be applied to a stopper, by detecting approach to a rack end with a rack end determining section without using a mechanism, controlling a current command value so as to gradually reduce when approaching the rack end or reaching a steering limit, and generating electromagnetic brake in the timing when the limited current command value becomes zero.例文帳に追加
機構を使用することなく、ラックエンド判定部によりラックエンドに近づいたことを検出し、ラックエンドに近づいた時或いは操舵限界に達したときに電流指令値を徐々に下げる制限を加え、制限を加えた電流指令値が零になるタイミングに合わせて電磁ブレーキを発生させることにより、ストッパへの衝撃を緩和させるようにした電動パワーステアリング装置の制御装置を提供する。 - 特許庁
An inlet volume adjusting valve 4 is driven electrically by a pump drive circuit (EDU) of the ECU 9 to a side where pump pressure feeding volume decreases and thereby a driving current flowing to the inlet volume adjusting valve 4 becomes zero, so that abnormal high pressure condition is prevented which is caused by an excessive pressure feeding of a supply pump 3 within a high pressure pipe passage.例文帳に追加
そして、ECU9のポンプ駆動回路(EDU)によって入り口調量弁4をポンプ圧送量が減少する側に電気的に駆動することで、入り口調量弁4への駆動電流が無くなることによるサプライポンプ3の過剰圧送による高圧配管経路(システム)内の異常高圧状態を防止できる。 - 特許庁
After turning off the gate signal for turning on a triac Q in a phase angle control circuit 1, an input current Iin becomes zero by immediately discharging electric charge charged into a capacitor Cx in a filter circuit 7 or a capacitor C2 for eliminating harmonic noises while constantly turning on a switching device Q1.例文帳に追加
位相角制御回路1のトライアックQをターンオンさせるゲート信号がオフした以降において、スイッチング素子Q1を常時オンとすることでフィルタ回路7のコンデンサCxや高調波ノイズ除去用のコンデンサC2に充電された電荷を瞬時に放電して入力電流Iinをゼロにする。 - 特許庁
A constant voltage circuit uses a transistor with large current amplification factor as a semiconductor device, a combination of transistors with Darlington connection, if necessary, and a constant voltage diode with the voltage temperature characteristics for compensating the voltage temperature characteristics of base-emitter of the transistor to make the constant voltage temperature zero in combination, thereby obtaining the semiconductor device with excellent voltage drop characteristic and a circuit of excellent constant voltage characteristics.例文帳に追加
半導体素子として電流増幅率の大きいトランジスター、必要であるならばダーリントン接続トランジスター組み合わせ、定電圧温度特性ゼロになる組み合わせのトランジスターのベース−エミッタ間電圧温度特性と補償できる電圧温度特性の定電圧ダイオードを使う。 - 特許庁
In a phase near zero voltage of a pulsating voltage or an alternating current source voltage which is such an output of a rectifier 43 as poses a problem to efficient and stable lighting of a discharge lamp 52, the on-period of the switching device 45 for controlling discharge of a capacitor 44 in a parallel relation to an output end of the rectifier is narrowed.例文帳に追加
放電灯52の点灯の効率化、安定化に問題となる整流装置43の出力である脈流電圧すなわち交流電源電圧の零電圧近傍位相では、整流装置の出力端と並列的関係にあるコンデンサ44の放電を制御するスイッチング装置45のオン期間を狭める。 - 特許庁
Protection diodes D11, D13, D15 within the semiconductor device are turned on when a PIN 1 terminal of the burn-in substrate 2 is connected normally to a control terminal of the the semiconductor device to make a current flow into an electric power source VCC side, a voltage of the PIN 1 terminal goes down thereby in the vicinity of 0 V, and a monitor output comes to zero therein.例文帳に追加
バーンイン基板2のPIN1端子と半導体装置の制御端子との接触が正常である場合には、半導体装置内の保護ダイオードD11、D13、D15がONとなり電源VCC側へ電流が流れ込むため、PIN1端子の電圧は0V近くまで降下し、モニター出力は0Vとなる。 - 特許庁
A ZGP (Zero Gauss Plane) is placed at an upper portion of a silicon melt 12 by applying asymmetric magnetic fields along the axis direction of a chamber by coil members 16, 17 arranged at the outside of the growing apparatus of the silicon single crystal ingot 10 and controlling the ratio and intensity of the asymmetric magnetic fields by current control or the like without additional constitutive elements.例文帳に追加
シリコン単結晶インゴット10の成長装置の外側に配置されたコイル部材16,17によって、チャンバの軸方向に沿って非対称磁場を印加し、非対称磁場の比率または強さを電流制御などで付加的な構成要素なく制御し、ZGPZero Gauss Planeがシリコン融液12の表面上部に位置するようにする。 - 特許庁
To provide a control method for resonance DC-DC converter capable of maintaining zero-voltage switching of a switching device even if an auxiliary resonance circuit is not connected during low load current of light load and attaining high efficiency because no connection of the auxiliary resonance circuit eliminates loss resulting from the auxiliary resonance circuit.例文帳に追加
軽負荷の低負荷電流時において補助共振回路を接続しなくてもスイッチング素子のゼロ電圧スイッチングを維持でき、更に補助共振回路を接続しないため補助共振回路に起因する損失がなくなるため高効率化を図ることが可能な共振型DC−DCコンバータの制御方法を提供すること。 - 特許庁
The control device for the motor comprises a PWM-excitation phase synchronization control means (102) for making an excitation phase switching timing phase and a PWM off timing phase synchronize with zero degree in a motor drive system for constant-speed control of the motor by controlling an energizing current via the excitation phase switching and the PWM control.例文帳に追加
励磁相切替えとPWM制御により通電電流制御を行い、モーターの定速制御を行うモーター駆動システムにおいて、励磁相切替えタイミング位相とPWMオフタイミング位相を0度に同期させるPWM励磁相同期制御手段(102)を有したことを特徴とするモーター制御装置。 - 特許庁
Current IX is made to flow from a control circuit CCO to the connected point of the first resistance R1 and the sensing resistance RS so that the potential difference between the potential VS in the connected point of the sensing resistance RS and the first resistance R1 and the potential V3 in the connected point of the second resistance R2 and the third resistance R3 becomes zero.例文帳に追加
感知抵抗R_Sと第1の抵抗R_1との接続点の電位V_Sと、第2の抵抗R_2と第3の抵抗R_3との接続点の電位V_3との電位差が0となるよう、第1の抵抗R_1と感知抵抗R_sとの接続点に、制御回路CC0から電流I_Xを流すものとする。 - 特許庁
By properly deciding the conditions of the rotational position θ of the rotor at the time of converting the detected values Iu, Iv, and Iw of an AC current flowing to the winding of each phase of a motor 21 into two axes of rotatory coordinate system Id and Iq, Id becomes roughly zero regardless of θ, and Iq becomes an roughly constant value regardless of θ.例文帳に追加
モータ21の各相の巻線に流れる交流電流の検出値Iu、Iv、Iwを2軸の回転座標系Id、Iqに変換する際のロータの回転位置θの条件を適宜に定めることにより、Idがθに依らずほぼ0になり、Iqはθに依らずほぼ一定値になる。 - 特許庁
Further, the conductive bars 103 of the circuit interrupting blocks 100 arranged outside are arranged outside the conductive bars 103 of the circuit interrupting blocks arranged inside, while, each circuit interrupting block 100 is supported by the conductive bars 103 in free turning with the zero-phase current transformer CT as a center.例文帳に追加
また、外側に配置された回路遮断ブロック100の導電バー103は、内側に配置された回路遮断ブロック100の導電バー103よりも外側に配置され、さらに各回路遮断ブロック100は零相変流器CTを中心として回動自在に導電バー103に支持されている。 - 特許庁
Moreover, a standard input part 24 is connected to the input end of a second superconducting circuit block 22, and a small number of element parameters of the standard input part are adjusted in advance, so as to set substantially to zero the static inflow or outflow of a current at the input end of the standard input part in question.例文帳に追加
また、第2の超伝導回路ブロック22の入力端に標準入力部24を接続し、当該標準入力部24の入力端における電流の静的な流入または流出を実質上ゼロにするように標準入力部の少数の素子パラメータを予め調整する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|