| 意味 | 例文 |
difference setの部分一致の例文一覧と使い方
該当件数 : 2331件
To provide a mixing container uniformly mixing even in the case of a plurality of kinds of fluids of large viscosity difference and gravity difference or mixing a liquid with a granule, not generating solids caused by a liquid component even in the case of the liquid component reacting with a water content in air and being set and uniformly mixing even the bottom of the container.例文帳に追加
粘度差や比重の差の大きい複数種の液体、又は液体と粉粒体を混合したい場合でも均一に混合することができ、さらに混合されるべき液体等の中に、空気中の水分と反応して固化する液体成分がある場合であっても、上記液体成分に起因する固形物が発生せず、容器の底部も均一に混合することのできる混合容器を提供する。 - 特許庁
The controller 106 decides any one of the air supply valves MAV-M and MAV-B and the general exhaust valves GEX-M and GEX-B as a room pressure valve, and controls the room pressure valve so that a pressure difference measured by the differential pressure sensor 109 conforms to a set value.例文帳に追加
コントローラ106は、給気バルブMAV−M,MAV−Bと一般排気バルブGEX−M,GEX−Bのうち何れか1つを室圧バルブとして決定し、差圧センサ109によって計測された圧力差が設定値に一致するように室圧バルブを制御する。 - 特許庁
Also, each voltage difference (Margin ΔVm) between write discrimination voltage Va for each data value and read voltage Vr being adjacent to the lower potential side of Va is set so that ΔVm at higher threshold voltage Vtm which tends to drop easily owing to deterioration of electric charge holding is made higher.例文帳に追加
また、各データ値に対する書き込み判定電圧Va とその低電位側に隣接する読み出し電圧Vr との各電圧差(マージンΔVm )を、電荷保持劣化によるしきい値電圧Vtmの低下が生じ易いしきい値電圧Vtmの高いものほど順次大きくなるように設定する。 - 特許庁
Since the coordinate reader can calculate the cycles T1, T2 by measuring them by a system clock and the attributes of the pen are detected at least with over one cycle of the system clock as difference of the cycle T1, considerable number of attributes are set.例文帳に追加
座標読取装置は、周期T1,T2をシステムクロックにより計測して求めることができるため、周期T1の差としては、少なくともシステムクロックの1周期以上あれば、ペンの属性を検出することができるので、非常の多くの属性を設定することができる。 - 特許庁
A model prediction control unit 30 predicts a current to be achieved by each of voltage vectors set by an operation state setter 31, thereby setting a voltage vector having the smallest difference from a command voltage as the final operation state of the inverter IV.例文帳に追加
モデル予測制御部30では、操作状態設定部31の設定する電圧ベクトルのそれぞれについて、これによって実現される電流を予測することで、指令電流との差が最も小さくなる電圧ベクトルをインバータIVの最終的な操作状態として設定する。 - 特許庁
Then in a step S13, pixel values in the difference image is decided in advance and pixels whose value is greater than a threshold TH1 with correlation to a paper transmittance are regarded to be an error in the set-off reduction processing and the pixel value of the input image is outputted as it is (step S18).例文帳に追加
次に、ステップS13にて、差分画像中の画素値が、予め決められ、紙の透過率と相関がある閾値TH1よりも大きい画素については、裏写り軽減処理における誤りとみなし、入力画像の画素値をそのまま出力とする(ステップS18)。 - 特許庁
Therefore, the optimum characteristic is calculated based on the muscle state of the drier, the calculated optimum steering characteristic is transmitted to the steering control unit 50 of the automobile 3 of the driver, and the steering characteristic is changed, and thereby the optimum steering characteristic in accordance with the difference of the muscular strength of the driver can be set.例文帳に追加
従って、ドライバの筋状態に基づいて最適な操舵特性が算出され、算出された最適な操舵特性がそのドライバの自動車3の操舵制御ユニット50に転送され、操舵特性が変更されるため、ドライバの筋力の違いに応じた最適な操舵特性を設定できる。 - 特許庁
When the rotation speed n of the engine 22 is judged to change from the start mode to the normal mode, a difference Δne between the detection value of the rotation speed sensor 31a and a target rotation speed n0 beforehand set is calculated and ignition timing θ1 is controlled based on the calculated value.例文帳に追加
そして、エンジン22の回転速度nが始動モードから通常モードに変わったことを判定すると、回転速度センサ31aの検出値と、予め設定された目標回転速度n0との差分Δneを算出し、その算出値に基づいて、点火時期θ1を制御するようにした。 - 特許庁
Adjacent LED chips 80 are provided such that a driving time difference for exposing or reading the image at an identical position between the adjacent LED chips 80 is set to be a value which is an integer multiple number of a least common multiple of a plurality of vibration cycles generated by the driving mechanism.例文帳に追加
隣接する各LEDチップ80は、この各LEDチップ80が同一点に画像を露光する駆動時間差あるいは同一点の画像を読取る駆動時間差が駆動機構から生じる複数の振動周期の最小公倍数の整数倍となるように設定されている。 - 特許庁
A difference of each coordinate component between color data on the inspection surface and first acceptable quality reference color information corresponding to the coordinate component of color data on the inspection surface of the first acceptable quality color information which is set in advance is obtained, and a first image data comprising a result thus obtained is formed.例文帳に追加
検査面色データと、予め設定された第一良品基準色情報のうち検査面色データの座標成分に対応する第一良品基準色データとの各座標成分の差を得るとともに、その処理結果からなる第一画像データを作成する。 - 特許庁
The apparatus for detecting membrane defect comprises a reference electrode 16; detecting electrodes 17a, 17b, 17c and 17d set at least on the permeating liquid side of the membrane; and a measuring means 18 for continuously measuring a potential difference between the reference electrode and each detecting electrode.例文帳に追加
また、基準電極16と、少なくとも膜の透過液側に設置される検知電極17a,17b,17c,17dと、前記基準電極と前記検知電極との間の電位差を連続的に測定する測定手段18と、を有することを特徴とする膜欠陥検出装置である。 - 特許庁
To provide an inkjet recording apparatus and a maintenance method which can efficiently solve a color mixing phenomenon generated by accompanying the ripple in an ink storing part and the difference in a specific gravity of ink while an ink set of color pigment inks equipped with the ink storing part which remains substantially closed is used.例文帳に追加
実質的に密閉状態となるインク収容部を備えたカラー顔料インクのインクセットを用いながらも、インク収容部のリップルやインクの比重の差に伴って発生する混色現象を、効率的に解決することが可能なインクジェット記録装置およびメンテナンス方法を提供する。 - 特許庁
In 6 pixel columns constituted of four pixels set on 16 pixels in the neighbor of a pixel to be interpolated on an image shown by image data S0, the absolute value of a difference between pixels is obtained, and whether or not an edge is present between the central two pixels is determined based on the above absolute value.例文帳に追加
画像データS0により表される画像上において、補間画素の近傍の16画素上に設定された4画素からなる6つの画素列において、画素間の差分の絶対値を求め、これに基づいて中央の2つの画素間にエッジが存在するか否かを判定する。 - 特許庁
When an optical path length difference of a wavelength filter is chirp-modulated (chirped); an adjacent mode suppression ratio to the main mode by chirping, a light confinement coefficient of an active layer and the active layer length, and the desired wavelength variable region Δλ_c, are set in a prescribed relation.例文帳に追加
また、波長フィルタの光路長差をチャープ変調(チャーピング)する際に、チャーピングによる主モードに対する隣接モード抑圧比、活性層の光閉じ込め係数、活性層長などと、所望の波長可変領域Δλ_cとを、所定の関係になるように設定した。 - 特許庁
A recess section 84 which is almost the same shape with a model name display plate 80 displaying the model name or the like is formed in a game board 30, and the model name display plate 80 is set so that the model name can fit in the recess section 84, then, difference in level between the model name display plate 80 and the game board 30 is eliminated.例文帳に追加
機種名等を表示する機種目名表示プレート80と略同形状の凹部84を遊技盤30に設けるとともに、当該凹部84に機種目名表示プレート80を嵌め込むように取り付けることにより、機種目名表示プレート80と遊技盤30との段差がなくなる。 - 特許庁
A conveying speed of the second conveying means 109 is set higher than that of the first conveying means 105, and by a difference between these conveying speeds, the sheet in a condition of being held by the first/second conveying means 105, 109 is pressed to a curved part 106A of the guide member 106 at conveying time.例文帳に追加
そして、第1搬送手段105よりも第2搬送手段109の搬送速度を速くし、この搬送速度差により、搬送時、第1及び第2搬送手段105,109によって挟持された状態のシートをガイド部材106の湾曲部106Aに押し付けるようにする。 - 特許庁
The slip control is executed for controlling an operation quantity of the lockup clutch (on and after t11) based on a control target value Vd set based on a vehicle operation state for adjusting a rotating speed difference (the amount of slip) between the input side and the output side of the torque converter to a target amount of slip.例文帳に追加
トルクコンバータの入力側と出力側との回転速度差(スリップ量)を目標スリップ量に調節するために車両運転状態に基づき設定される制御目標値Vdに基づいてロックアップクラッチの作動量を制御するスリップ制御を実行する(t11以降)。 - 特許庁
The oscillation frequencies F_LO1, F_LO2 of a first and a second local oscillation signals LO1, LO2 are set to the sum and the difference of the frequencies F_RF1, F_RF2 of a first and a second radio frequency signals RF1, RF2 and the frequency F_IF of an intermediate frequency signal IF, respectively.例文帳に追加
そして、第1,第2の局部発振信号LO1,LO2の発振周波数F_LO1,F_LO2を第1,第2の無線周波数信号RF1,RF2の周波数F_RF1,F_RF2と中間周波数信号IFの周波数F_IFとの和,差にそれぞれ設定する。 - 特許庁
To present 24 frames per second film via a 60 Hz television system with the "look" of a 72 Hz cinemetric projector, a judder oscillator is set to generate a 24 Hz sinewave having a peak amplitude equal to 38.5% of the time difference between 24 Hz frames.例文帳に追加
24フレーム/秒の映画フィルムを60Hzのテレビジョンシステムを介して72Hzのプロジェクタの「外見」で表示しようとする場合、24Hzフレーム間の時間差の38.5%に等しいピーク振幅を有する24Hzの正弦曲線を生成するようにジャダー発振器の設定を行う。 - 特許庁
A color-difference component address selecting part 11A selects an address generated by a LUT access address generating part 9A when the LUT signal is supplied from the selector set value calculating part 6 and selects a luminance component from a number of through data stages adjusting part 10A when the through signal is supplied.例文帳に追加
色差成分アドレス選択部11Aは、セレクタ設定値計算部6からLUT信号が供給されたときは、LUTアクセスアドレス生成部9Aで生成されたアドレスを選択し、スルー信号が供給されたときは、スルーデータ段数調整部10Aからの輝度成分を選択する。 - 特許庁
Position relation between the reluctors, and position relation between the first and second pulsars are set so that difference is generated between a phase relation between an output pulse of the pulser A and an output pulse of the pulser B in normal rotation of the engine, and a phase relation of that in reverse rotation of the engine.例文帳に追加
機関が正回転しているときと逆回転しているときとでパルサAの出力パルスとパルサBの出力パルスとの間の位相関係に差が生じるように、リラクタ相互間の位置関係と、第1及び第2のパルサ相互間の位置関係とを設定する。 - 特許庁
At this time, the difference between the memory potential stored in the memory element 145 at the dark time and an amplifier reference potential given to the read amplifier 146 is detected by a digital operation circuit 150, and the amplifier reference potential is set to the memory potential at the dark time or a potential proximate to it.例文帳に追加
このとき、デジタル演算回路150にて、暗時におけるメモリ素子145に蓄積されたメモリ電位と読み出しアンプ146に与えるアンプ基準電位との差が検出され、アンプ基準電位を暗時のメモリ電位、あるいはその近傍電位に演算設定することが行われる。 - 特許庁
Consequently, the voltage difference (margin ΔVd) between the maximum value of the threshold voltage Vtm of each data value and read voltage Vr being adjacent to the higher potential side of Vtm is set so that Δd at lower threshold voltage Vtm which tends to rise easily owing to high voltage stress is made higher.例文帳に追加
その結果、各データ値のしきい値電圧Vtmの最大値とその高電位側に隣接する読み出し電圧Vr との電圧差(マージンΔVd )は、高電圧ストレスによるしきい値電圧Vtmの上昇が発生し易いしきい値電圧Vtmの低いものほど順次大きくなるように設定される。 - 特許庁
A difference |L1-L2| between dimensions L1 and L2 on both sides by sandwiching the center line C of the dynamic pressure grooves 3a and 3b is set to 1% or less of the total length (L1+L2), so as to restrain generation of the shaft directional flow of the lubricating fluid caused by shaft directional asymmetry of herringbone pattern.例文帳に追加
動圧溝3a(3b)の中心線Cを挟んでその両側の寸法L_1とL_2 の差|L_1 −L_2 |を、その全長(L_1 +L_2 )の1%以下とすることにより、ヘリングボーンパターンの軸方向への非対称性に起因する潤滑流体の軸方向への流れの発生を抑制する。 - 特許庁
Provided that a room pressure control device 1A is constructed as such, the interior of the room 61 is set to arbitrary pressure owing to a difference between the supply air amount and the exhaust air amount, and the air amount is varied in response to a thermal load in the room, whereby it is possible to keep the temperature in the room unchanged.例文帳に追加
このように室圧制御装置1Aを構成すれば、給気風量と排気風量の差によって室61の内部を任意圧力に設定するとともに、室内の熱負荷に応じて風量を変動させ、前記室内の温度を一定に保つことが可能になる。 - 特許庁
A phase adjusting filter 13 and a gain adjusting filter 14 are provided, and the upper and the lower acceleration M is advanced by 49 degree near a resonance point of a car body, and a phase difference of the upper and the lower acceleration M in relation to the relative velocity is set at 180 degree so that the relative velocity and the phase coincide with each other.例文帳に追加
位相調整フィルタ13及びゲイン調整フィルタ14を設け、車体共振点付近で、上下加速度Mを49度進ませて、相対速度に対する上下加速度Mの位相差を180度にして、相対速度と位相を合わせるようにしている。 - 特許庁
To provide a technique for controlling power consumption and preventing the service life of an air conditioner from decreasing, even if the temperature difference between an indoor temperature and the set temperature of a heating-cooling combination appliance is equal to or more than the capacity of the heating-cooling combination appliance, and indoor air is leaking, in the air conditioner.例文帳に追加
空気調和装置において、室内温度と冷暖房機の設定温度との間の温度差が冷暖房機の能力以上にあったり、室内空気が漏洩していても、電力消費の抑制と装置の寿命短縮の防止ができる技術を提供する。 - 特許庁
To provide a bench with handrails to be set in a doorway to the interior such as an entrance of a building, allowing the elderly or the disabled to easily put on shoes for going out and to ascend/descend the level difference in the entrance rail by improving the usability of the handrails and the bench and improving the workability in construction.例文帳に追加
建物の玄関等の屋内出入り口に設置される、手すりとベンチの使い勝手、施工性、等を向上させて、高齢者や身障者が外出するために靴を履く作業や上り框の段差の昇り降り等を容易に行なうことができる手すり付ベンチを提供する。 - 特許庁
To provide a vehicle burglary and robbery prevention device capable of alarming that security cannot be set regardless of a difference of orders of closing motion of a first opening and closing body and a second opening and closing body when wireless locking operation of the first opening and closing body is carried out when the first opening and closing body and the second opening and closing body open.例文帳に追加
第1開閉体及び第2開閉体が開いているときに第1開閉体のワイヤレスドアロック操作が行われると、第1開閉体の閉動作と第2開閉体の閉動作との順番の違いに関わらず、セキュリティがセットできなかったことを警告できるようにする。 - 特許庁
Next, referring to the obtained logarithmic values by the number of the BPFs, a band-pass filter corresponding to the logarithmic value of which the difference between a minimum value and a maximum value among the logarithmic values becomes to be maximum is decided, looking at the logarithmic values in order from the one to the BPF 50 of which the center frequency is set to be lowest.例文帳に追加
次いで、BPFの数だけ求められた対数値を参照して、中心周波数が最も低く設定されているBPF50に対する対数値から順に見て、対数値の極小値と極大値との差が最も大きくなる対数値に対応するバンドパスフィルタを決定する。 - 特許庁
A plurality of periodic time-stamp packets are transmitted to a communications apparatus of a receiver side with a testing transmission rate (R) set currently, and the variation trend of the transmission delay time difference between the time-stamp packets is evaluated, based on the respective times at which the time-stamp packets are received by the communications apparatus of the receiver side.例文帳に追加
複数の周期的なタイムスタンプパケットを、受信側の通信装置へ、現在設定されている試験伝送率(R)で伝送し、受信側の通信装置にタイムスタンプパケットのそれぞれが受信された時刻に基づいて、タイムスタンプパケット間の伝送遅延時間差の変化傾向を検査する。 - 特許庁
When the temperature difference between the room temperature Tr and a set temperature Ts is >3°C, the step advances from step ST2 to step ST3 and an electronic expansion valve between an outdoor machine-side heat exchanger and the indoor machine-side heat exchanger is controlled so that the inlet temperature of the indoor machine-side heat exchanger may become equal to the outlet temperature of the heat exchanger.例文帳に追加
この室温Trと設定温度Tsの差が3℃より大きいときには、ステップST2からST3に進み、室内機側熱交換器の入口温度が、その出口温度になるように室外熱交換器と同室内機側熱交換器との間の電子膨張弁を制御する。 - 特許庁
The heat-resistant resin is a polyimide or a polyamide-imide, and by making its imidization ratio set at 20 to 70% the stimulable phosphor layer 12 glued surely to the support 11; and the film ruptures of the stimulable phosphor layer can be prevented by the difference in thermal expansion coefficients from the substrate.例文帳に追加
耐熱性樹脂はポリイミドまたはポリアミドイミドであり、そのイミド化率を20〜70%とすることで、輝尽性蛍光体層を支持体上に確実に接着するとともに、基板との熱膨張係数の差によって輝尽性蛍光体層の膜割れを防ぐことができる。 - 特許庁
A synchronous determining circuit 7 compares the mean value data with the internal state information of the recovery circuit in the case that synchronous processing of each reproduced signal previously set and the reception signal is stable, and notifies switching of a loop band in each reproduced signal from the difference thereof.例文帳に追加
同期判定回路7は平均値データと、予め設定されている各再生信号と受信信号との同期処理が安定している場合における再生回路内部状態情報とを比較し、その差から各再生回路におけるループバンドの切替えを通知する。 - 特許庁
To prevent an output voltage waveform of an inverter detected as an asymmetric waveform from being distorted in an inverter power generator when there is a difference between an A/D conversion value of a reference voltage set by an output voltage detecting circuit and a reference value stored in a controller.例文帳に追加
インバータ発電装置において、出力電圧検出回路に設定された基準電圧のA/D変換値とコントローラに記憶された参照値との間に差があるときに出力電圧が正負非対称な波形として検出されてインバータの出力電圧波形が歪むのを防止する。 - 特許庁
Thereafter, a voltage is applied between the electrode layer and the conductive porous body so that the difference between the electrode potential of the electrode layer and the potential of the conductive porous body is set at a value allowing an electrochemical oxidation reaction generating a hydrophilic group on the conductive porous body surface to be progressed.例文帳に追加
その後、電極層における電極電位と導電性多孔質体における電位との差が、導電性多孔質体表面で親水基を生じる電気化学的酸化反応が進行可能となる値となるように、電極層と導電性多孔質体との間に電圧を印加する。 - 特許庁
The image signal checking device 3(30) calculates, with its comparison section 34, the difference (increment or decrement) between the signal level of image signals and synchronization signals in image signals inputted through a transmission line and the reference signal level of image signals and synchronization signals which is previously set.例文帳に追加
映像信号チェック装置3(30)は、比較部34が、伝送路から入力された映像信号中の画像信号および同期信号の信号レベルと予め設定されている画像信号および同期信号の基準信号レベルとを比較して増減差を算出する。 - 特許庁
To provide a susceptor wherein the distance between an inside surface of a wafer mounting part and a peripheral edge of a wafer is set constant regardless of the difference of tapering of the wafer when abutting parts formed in a circumferential part of the wafer mounting part abut on the wafer while preventing occurrence of sticking between the wafer and the susceptor.例文帳に追加
ウェーハとサセプタとの間のスティッキングの発生を防止しつつ、ウェーハ載置部の外周部に設けられた当接部とウェーハとが当接した際に、ウェーハのテーパー加工の違いによらずウェーハ載置部の内周面とウェーハ外周縁との距離が一定となるようなサセプタを提供すること。 - 特許庁
Both the detecting coils 20A and 20B are provided with a difference in number of turns so that the magnitude of the differential AC shows a linear output characteristic in the detecting range of load torque when a load torque is added in the detecting range within a maximum detected load torque set every rotating direction to a shaft S.例文帳に追加
両検出用コイル20A,20Bは、シャフトSに対して回転方向毎に設定されている最大検出負荷トルク以内の検出範囲で負荷トルクが加わったときの差分交流の大きさが負荷トルクの検出範囲で線形な出力特性となるように巻き数に差を設ける。 - 特許庁
A data mask control circuit 16e sets a mask control signal MS to an active state on the basis of storage contents of the setting value circuit 16h in timing when a luminance signal YVD and a color difference signal CVD corresponding to the set display position are fed to a data selection switch YSW.例文帳に追加
データマスク制御回路16eは、設定値回路16hの記憶内容に基づいて、設定された表示位置に対応する輝度信号YVDおよび色差信号CVDがデータ選択スイッチYSWに伝達されるタイミングにおいて、マスク制御信号MSを活性状態に設定する。 - 特許庁
Consequently, amount of scavenging air corresponding to type of machine can be set by simple setting for changing a position in the direction of axial line of the valve element in accordance with difference in type of machine of engine and it is unnecessary to change parts individually as in a conventional case, thereby reducing manufacturing cost.例文帳に追加
これにより、エンジンの機種違いに応じて弁体の軸線方向位置を変えるという簡単な設定で、機種別に対応した掃気空気量の設定をすることができ、従来のように個別に部品を変える必要が無くなるため、製品コストを低廉化し得る。 - 特許庁
This boss structure 1 is characterized in that the motor shaft radial directional length L1 of the level difference surface 13 adjacent to the vibration control member 12 is set to 1/2 or more of the motor shaft radial directional length L2 of an end surface adjacent to the stepped surface 13 of the vibration control member 12.例文帳に追加
さらに、このボス構造1は、防振部材12と隣接する段差面13のモーター軸放射方向の長さL1が、防振部材12の段差面13と隣接する端面のモーター軸放射方向の長さL2の2分の1以上であることを特徴とするボス構造である。 - 特許庁
An 8×8 region having 8 pixels respectively in the longitudinal and lateral directions in contact with the boundary is set for extracting a part of pixels (S1), an average value of signal levels of the left and right regions is evaluated, and the value which negates the signal level difference is evaluated from the average value (S2, S3).例文帳に追加
画素の一部を抽出するために、境界に接して画素を縦横にそれぞれ8個有した8×8領域を設定し(S1)、左右両領域の信号レベルの平均値を求めて、それらの平均値から信号レベル差を打ち消す値を求める(S2,S3)。 - 特許庁
The dehydrating treatment temperature is set according to the outer diameter of a porous glass preform 10 because the volatilizing amount of germanium, largely affecting the specific refractive index difference Δn of the optical fiber preform 20, is determined by the outer diameter of a porous glass preform 10 and the dehydrating treatment temperature.例文帳に追加
光ファイバ母材20の比屈折率差Δnに大きく影響するゲルマニウムの揮散量が、処理される多孔質ガラス母材10の外径と脱水処理温度によって決定されることから、多孔質ガラス母材10の外径に応じて脱水処理温度を設定する。 - 特許庁
Thus, since a temperature change in the additive agent can be reduced, a difference between a supply quantity of the additive agent set as a control target value and an actually-supplied supply quantity can be reduced, and the exhaust emission control device can be efficiently operated.例文帳に追加
これにより、添加剤の温度変化を小さくすることができるので、制御目標値として設定された添加剤の供給量と、実際に供給された供給量との差を小さくすることが可能となり、排気浄化装置を効率的に作動させることができ得る。 - 特許庁
In the substrate for mounting a component with a lead wire, a clearance, i.e., a difference between the diameter of the lead wire of a component and the diameter of a through hole provided in the substrate, is set in the range of 0.5-0.8 mm.例文帳に追加
本発明の基板は、リード線を有する部品が搭載される基板において、前記部品のリード線のリード径と、前記基板上に設けられたスルーホールのスルーホール径との差分であるクリアランスを、0.5ミリより大きく、かつ、0.8ミリ以下の範囲に含まれるいずれかの値に設定した基板である。 - 特許庁
In the AF of an optical path length difference system, the filters of a processing part to generate a focus evaluated value for the respective video signals obtained from two imaging devices for detecting a focusing state 32A and 32B are set to be switched between HPFs 82A and 82B, and BPFs 83A and 83B.例文帳に追加
光路長差方式のAFにおいて、2つのピント状態検出用撮像素子32A、32Bから得られた映像信号のそれぞれに対して焦点評価値を生成する処理部のフィルタをHPF82A、82BとBPF83A、83Bとで切り替えられるようにする。 - 特許庁
The network delay monitor is provided with a reception means that sets a received time to event information sent via a network from a monitor object device while a transmission time is set to the information and a calculation means that calculates a delay time in the network depending on a difference between the reception time and the transmission time.例文帳に追加
監視対象装置から発信時刻が設定されてネットワークを介して送信されたイベント情報に受信時刻を設定する受信手段と、受信時刻と発信時刻との差からネットワークにおける遅延時間を算出する算出手段を備えたもの。 - 特許庁
Since the bias initial value at a setting start time is estimated from a difference between the detective position in the control not performing the integral compensation or the bias compensation and the estimate position, even when different bias values are shown on the same target position, the bias initial value of the setting control is set precisely.例文帳に追加
積分補償又はバイアス補償を行わない制御における検出位置と前記推定位置との差から整定開始時のバイアス初期値を推定するため、同一の目標位置で異なるバイアス値を示しても、整定制御のバイアス初期値が正確に設定される。 - 特許庁
A main control unit 19 adjusts the drive pulse waveform generated by a drive signal generation part 18 based on a difference between the flight speed of the liquid drops and the weight measured corresponding to the drive pulse of the standard waveform and the flight speed and the weight set as a target value.例文帳に追加
主制御部19は、基準波形の駆動パルスに対応して測定された液滴の飛行速度及び重量と、目標値として設定された飛行速度及び重量との差に基づいて、駆動信号発生部18が発生する駆動パルスの波形を調整する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|