off-timeの部分一致の例文一覧と使い方
該当件数 : 6584件
The switching control circuit 10a for controlling a switching element 62 has a threshold output device 18 for outputting a threshold that goes up as a time passes after turning on the switching element, and interrupting means 20, 22, 12 and 14 for turning off the switching element when a value corresponding to current caused to flow in the switching element exceeds the threshold.例文帳に追加
スイッチング素子62を制御するスイッチング制御回路10aであって、スイッチング素子をオンさせてからの時間が経過するのに従って上昇する閾値を出力する閾値出力器18と、スイッチング素子を流れる電流に対応する値が閾値を超えた時にスイッチング素子をオフさせる遮断手段20、22、12、14を有している。 - 特許庁
In a vehicle performing fuel cut of an engine in time of coasting of the vehicle, and lockup of an engine output shaft and a transmission input shaft, a lockup execution flag and a fuel cut execution flag are set as OFF on condition that a brake pressure integrated value exceeds a fixed release decision value β, and release of the lockup and the restoration from the fuel cut are executed.例文帳に追加
車両の惰性走行時にエンジンのフューエルカットと、エンジン出力軸及び変速機入力軸のロックアップと、を行う車両にあって、ブレーキ圧積算値が既定の解除判定値βを超えることを条件に、ロックアップ実行フラグ及びフューエルカット実行フラグをオフにセットして、ロックアップの開放とフューエルカットからの復帰とを実施するようにした。 - 特許庁
The grip is held with one or both hands to apply the blade inclining to the surface of the wooden chopping block to attain draining and scraping-off of the unwashed food residue with two linear acute-angled cutting edges while maintaining and reclaiming the surface condition of the wooden chopping block (grinding, polishing and flattening of the surface) and grinding the surface of wood at the same time.例文帳に追加
片手あるいは両手で持ち、木製まな板表面に本発明の刃(ブレード)を傾けて当て、2本ある直線の鋭角の切り刃で、水切りと洗い残した食物残渣を削り取ることができ、同時に木製まな板表面のコンデションの維持、再生(表面の研削研磨、平面出し)や木材表面の研削が出来るのが本発明である。 - 特許庁
Even when an unauthorized radio wave having repeated H and L signals with a short cycle length of 4ms, is applied, once a CPU of a main controller sends a fraud signal to a sub unified controller (fraud flag on), a fraud clear signal (fraud flag off) is not sent during a time T1, so that the load of processing the CPU of the main controller is reduced.例文帳に追加
短い周期4msでHとLを繰り返される不正電波を照射されても、主制御装置のCPUは、サブ統合制御装置に不正信号を一旦送信(不正フラグの立ち上がり)すると、時間T1 の間は不正クリア信号を送信(不正フラグの立ち下がり)しないので、主制御装置のCPUの処理負担は軽い。 - 特許庁
At least a pressure sensitive rubber (representative term for a pressure sensor rubber including equivalents thereof) is used in the grip part, an extreme variability in a quality and characteristic of the pressure sensitive rubber is considered, and thus an electrode is provided, and changed to ON state only when an energization exceeds a fixed threshold value, then changed to OFF state when there is no new signal after a fixed time period.例文帳に追加
少なくとも、グリップ部に感圧(性)ゴム(同類を含めた圧力センサーゴムと言う用語の代表で用いた)を用い、感圧ゴムが、品質・特性が、極めてバラツクことを踏まえ、電極を設け、通電が一定の閥値(バツチ)を超えた時のみ、「オン」の状態にし、その後、一定時間後、新たな信号が無ければ、「オフ」の状態にする方法をとった。 - 特許庁
To provide a packaging container for a vending machine that can be opened from both ends of the container to excel in a deployment performance at the time of disposal, and can reduce sticking of a product within the vending machine during taking off because of its high specific gravity, and has a higher strength than a glass container and a higher water resistance than a paper container, and is inexpensive compared with a plastic container.例文帳に追加
容器の両端から開封することが出来、廃棄時の展開性に優れる包装容器であって、比重が大きく自動販売機で製品が途中で引っ掛かることが少ないようにすることが出来る、また、ガラス容器よりも強度が強く、紙容器よりも耐水性があり、プラスチック容器よりも安価な自動販売機用包装容器の提供。 - 特許庁
To provide a drill with a long life stably drilling for a long period of time by preventing a coating layer on the outer periphery side of a cutting blade from peeling off to secure the wear resistance and preventing cracking and chipping on the center side of the cutting blade even in high speed cutting, and to provide an insert for a drill attached to such the drill of a cutting edge replaceable type.例文帳に追加
高速切削においても切刃の外周部側でのコーティング層の剥離を防いで耐摩耗性を確保するとともに、切刃の中心部側ではクラックや欠損を防止して、長期に亙って安定した穴明け加工が可能な長寿命のドリル、および刃先交換式のこのようなドリルに取り付けられるドリル用インサートを提供する。 - 特許庁
At this time, a taper part 362 which is provided at the outer face of the engagement projection 36 and tapers off toward the rear face from the front face side of the reflection plate 34 is inserted into the insertion hole 323, thereby, relative positioning of the reflection plate 34 to the mounting substrate 32 can be certainly carried out, and the lighting source 31 can be positioned to the prescribed position of the reflection plate 34.例文帳に追加
このとき、嵌合凸部36の外面に設けられ、反射板34の前面側から裏面側に向けて先細りするテーパ部362を、嵌合穴323に挿嵌するので、実装基板32に対する反射板34の相対的位置決めを確実に行うことができ、光源31を反射板34の所定の位置に位置決めできる。 - 特許庁
Each time a TFT switch connected to each scan line is turned on, an analog leak level flowing out to a data line in a state where the TFT switch is off is detected before the TFT switch is turned on, and before the analog image signal is converted into a digital image signal, the analog image signal is corrected based upon the leak level.例文帳に追加
各走査線に接続されたTFTスイッチを走査線毎にオン状態にする度に、そのオン状態とする前にTFTスイッチがオフの状態でデータ線に流出するアナログのリークレベルを検出し、アナログの画像信号をデジタルの画像信号に変換する前に、そのリークレベルに基づいてアナログの画像信号を補正する。 - 特許庁
To provide a micro ion source device and an integrated micro ion source device excellent in economic efficiency enabling to carry out different processes with the same vacuum device at the same time, by cutting off unnecessary power for driving an ion source through use of a micro ion source, and capable of carrying out manufacturing of a large variety of small-scale MEMS products simply and at low cost.例文帳に追加
超小型のイオン源を用いることによりイオン源を駆動するための不要な電力を削減し、異なるプロセスを同一の真空装置で同時に行うことを可能とし、多品種・少量のMEMS製品の製造を簡便・安価に行える経済性に優れた超小型イオン源装置および集積型超小型イオン源装置を提供する - 特許庁
To provide an adhesive sheet taking a plastic or paper as a substrate, easily peeling off from bonded materials at directly after the pasting with the various bonded materials but showing a strong bonding property after passing a suitable time through, and an emulsion type adhesive used preferably for forming the adhesive layer of such the adhesive sheet.例文帳に追加
本発明は、プラスチックや紙などを基材とする粘着シートにおいて、各種被着体に貼り合わせ直後においては被着体から容易に剥離でき、適度な時間経過後においては強力な接着性を示す粘着シートおよび該粘着シートの粘着剤層の形成に好ましく用いられ得るエマルジョン型粘着剤を提供することを目的とする。 - 特許庁
A dice body formed of a regular hexagonal or polygonal body having different character displays such as figure, character, pattern or the like on each face is formed of a transparent or translucent material, and a light emission part which senses the vibration and result when throwing the dice to flash on and off for a scheduled time and a control circuit therefor are fitted within the dice body.例文帳に追加
各面に異なる数字・文字・図柄などのキャラクタ表示がなされた正六面体または正多面体よりなるサイコロ本体を、透明または半透明な材料で構成すると共に、前記サイコロ本体内に、サイコロが振られた際の振動、結果を感知して予定の時間、点滅する発光部およびその制御回路を装備している。 - 特許庁
To prevent mud and water from entering into an exhaust duct for ventilating the inside of a belt converter cover, and at the same time, flow discharged cooled air smoothly backward inside a frame without leaking to leg parts of a rider or the like, in a ride-on type off-road four-wheel traveling vehicle provided with a V-belt type continuously variable transmission.例文帳に追加
Vベルト式無段変速機を備えた騎乗型不整地四輪走行車において、ベルトコンバータカバー内を換気するための排気ダクト内に泥や水が侵入するのを防ぐと共に、排出される冷却空気を、ライダーの足部等に漏出することなく、フレーム内部を円滑に後方へ流すことができるようにすることである。 - 特許庁
After starting electric power supply to this cold cathode tube lighting device 1 from a constant voltage power source 2, a transistor 85 is turned off until electric charge gathers in a capacitor 86, and during that time, voltage outputted to an operational amplifier 7 from the tube electric current setting part 8 becomes a value V1 by dividing source voltage by a resistance 81 and resistances 82 to 83.例文帳に追加
定電圧電源2から冷陰極管点灯装置1への電力の供給が開始された後、コンデンサ86に電荷が溜まるまでの間、トランジスタ85はオフであり、その間、管電流設定部8から演算増幅器7へ出力される電圧は、抵抗81と抵抗82〜83とで電源電圧を分圧した値V1となる。 - 特許庁
Then a transmission control signal analysis control unit 251 of a command signal transmission device 260 of the control earth station has a function for variation to a setting value of ALC corresponding to the ratio of average electric power values before and after a time occupation ratio of each modulation system is varied before an occupation ratio of a modulation system in back-off operation is varied.例文帳に追加
そして、管制地球局におけるコマンド信号送信装置260の伝送制御信号解析制御部251は、バックオフ運用される変調方式の占有割合が変更される前に、各変調方式の時間占有割合が変更される前後の平均電力の比に対応した、ALCの設定値に変更する機能を備える。 - 特許庁
In the tape cutting method which cuts the empty tape discharged from a tape feeder 4 after picking up the electronic parts retained in the emboss part E of the empty tape T, the direction of cutting at the time of nipping off the empty tape T by fixed edge 18a and a mobile edge 18b is set at a roughly right angle to the surface of the empty tape T.例文帳に追加
空テープTのエンボス部E内に保持された状態の電子部品をピックアップした後にテープフィーダ4から排出される空テープTを切断するテープ切断方法において、空テープTを固定刃18aおよび可動刃18bによって挟断する際の切断方向を空テープTの表面に対して略直角に設定する。 - 特許庁
In this underground electromagnetic surveillance method, electromagnetic surveillance of cutting off energization to a transmission loop, producing a smoke ring phenomenon in which an eddy current propagates to the bedrock, and measuring attenuation of the eddy current as a change of a time function of an electromagnetic field using a receiving loop is repeatedly performed along a plurality of measurement points in a ground surface side (S1-S4).例文帳に追加
この地下電磁探査方法では、送信ループへの通電を遮断し地山に渦電流が伝播するスモークリング現象を発生させ、前記渦電流の減衰を受信ループを用い電磁場の時間関数の変化として測定する電磁探査を、地表面側の複数の測定ポイントに沿って繰り返し行なう(S1〜S4)。 - 特許庁
To cut off the loss of reseparation performance, staining resistance and slipping-out preventive performance with the lapse of time to a floor material originally ought to be possessed as a tile carpet slipping-out preventive pressure sensitive adhesive since a nonslipping pressure sensitive adhesive softens when a plasticizer such as DOP included in a tile carpet backing layer transfers to the nonslipping pressure sensitive adhesive.例文帳に追加
タイルカーペットバッキング層に含まれるDOPなどの可塑剤が、滑り止め感圧粘着剤に移行することによって滑り止め感圧粘着剤が軟化し、タイルカーペットズレ止め感圧粘着剤として本来もっていなくてはならない床材に対する再剥離性、非汚染性及びズレ止め性が経時的に失われていくことを遮断すること。 - 特許庁
To make a user grasp the rest of a battery in stages corresponding to the rest of the battery without abruptly turning off the power source of an information display device and also to prolong the driving time after the rest of the battery becomes small by suppressing the power consumption by switching to power-saving display mode when the rest of the battery becomes small.例文帳に追加
本発明は、情報表示装置において突然電源をオフとすることなく、電池残量に応じて段階的にユーザーに電池残量を把握させ、電池残量が少なくなった場合には省電力モード表示に切換えて消費電力を抑えてそれ以降の駆動時間の延長をはかることを同時に達成する。 - 特許庁
(2) The Registrar shall not be bound to recognise such agent who has been convicted of crimes involving fraud or dishonesty, or is an undischargedbankrupt or had been struck off or otherwise removed from the register of membership of any professional body, or suspended for the time being from practising by any such body or committee thereof.例文帳に追加
(2) 登録官は,代理人であって,詐欺若しくは不正行為を含む犯罪の有罪判決を受けたもの,又は未復権破産者となったもの,又は何らかの職能団体の会員名簿から抹消その他排除されたもの,又は当該団体若しくはその委員会により業務を行うことを現に差し止められているものを認知する義務はないものとする。 - 特許庁
Operating route command data RTD including a plurality of bus stops at which a bus 20 is expected to subsequently stop for users planning to get on and off; and expected time when the bus 20 departs from each of the plural bus stops are informed to the bus 20 according to a current operating plan formed by a control center 30 with respect to a received demand DMD.例文帳に追加
受信したデマンドDMDに応じて、管理センタ30により作成された現在運行計画に基づいて、今後に順次巡ることが予定される複数の乗車予定停留所及び該複数の乗車予定停留所それぞれからバス20が出発する予定時刻を含む運行経路指示データRTDが、バス20に通知される。 - 特許庁
To provide a heat-sensitive adhesive and a heat-sensitive adhesive material solving drawbacks seen in conventional heat-sensitive adhesives and excellent in tackiness to rough surfaces such as of corrugated boards and blocking resistance, particularly, to provide such a heat-sensitive adhesive and a heat-sensitive adhesive material causing no peeling off corrugated boards with the lapse of time.例文帳に追加
従来の感熱性粘着剤に見られる欠点を克服し、ダンボールのような粗面に対する粘着力と、耐ブロッキング性に優れた感熱性粘着剤及び感熱性粘着材料を提供することにあり、特に、ダンボールに対して経時で剥れてこない感熱性粘着剤及び感熱性粘着材料を提供する。 - 特許庁
In ordinary operation, the auxiliary transistor 12 is turned off and when the control signal is switched from a high level to a low level, electric charges stored in a parasitic capacitor inside the output transistor 6 are discharged through the input transistor 3 in a short time so that the switching control of the output transistor 6 can be performed at a high response speed to the control signal.例文帳に追加
通常動作時には補助トランジスタ12はオフしており、制御信号がハイレベルからロウレベルに切り替わった場合に、出力トランジスタ6内の寄生容量に蓄積された電荷が入力トランジスタ3を介して短時間で放電されるので、制御信号に対して、速い応答速度で出力トランジスタ6のスイッチング制御が行われる。 - 特許庁
When a data linking part 2 holds radio bearer information, that is, when user data is not transmitted from the upper layer after the radio bearer is set, a common flag 23 is off and at that time, a handler part 3 transmits corresponding dummy data (synchronous frame, etc.) stored beforehand in a memory area 33 from the lower layer closer to hardware to the upper layer.例文帳に追加
ハンドラ部3は、データリンク部2が無線ベアラ情報を保持したとき、すなわち無線ベアラ設定後、上位レイヤからユーザデータが送信されていない場合は、共通フラグ23がオフであり、そのときにはよりハードウェアに近い下位レイヤから上位レイヤに対応した、メモリ領域33に予め格納されているダミーデータ(同期フレーム等)の送信を行う。 - 特許庁
Each branch line is provided with heat conduction valves 12a, 12b, and when floor heating panels 13a, 13b are set to different temperatures at the same time, hot water corresponding to the floor heating panel 13a set to the highest temperature is circulated, and the thermal valve 12b corresponding to the floor heating panel 13b performs ON/OFF control corresponding to the set temperature.例文帳に追加
そして、それぞれの分岐経路に熱伝導弁12a、12bを設け、床暖房パネル13a、13bが複数同時に異なる温度に設定された場合は、最も高い温度に設定された床暖房パネル13aに対応する湯を循環すると共に床暖房パネル13bに対応する熱動弁12bは、設定温度に応じたオン・オフ制御を行う。 - 特許庁
To provide a tray for dental materials capable of eliminating the operation of wiping off an old excessive mixture from a small brush using tissue paper or the like every time by an operator for the phenomenon that it is accumulated on the small brush little by little during work by a brush-on technique and removing the excessive mixture at a brush tip easily even with one hand.例文帳に追加
筆積み法による作業中に古い余分な混合物が小筆に少量ずつ蓄積してしまう現象に対して、術者がその都度ティッシュペーパー等を用いて小筆から拭き取っていた操作を無くし、片手でも簡単に筆先の余分な混合物を除去することが可能な歯科材料用トレイを提供する。 - 特許庁
Meanwhile, when the driver's intention to slow down the vehicle with the creeping torque by decelerating the vehicle to the balancing speed even at the time of decelerating the vehicle, i.e., when the brake switch 5 is turned off and only the opening of the accelerator is zero, the drive motor is controlled with regeneration until its rpm reaches a given value which is set in advance.例文帳に追加
一方、車両の減速時でも、ドライバが釣合い車速まで減速することによって、クリープトルクだけで徐行しようという意図が明らかな場合、つまり、ブレーキスイッチ5がオフであり、アクセル開度のみが0である場合には、駆動モータの回転数が予め設定された所定値になるまで当該駆動モータを回生制御する。 - 特許庁
At inputting the selected PID control constant group, the temperature control part 23 changes the PID control constant group used until that time to the selected PID control constant group, and PID-controls the temperature of the hot water by ON/OFF-controlling a heater 17 by using each constant included in the selected PID control constant group.例文帳に追加
温度制御部23は、該選択したPID制御用定数群を入力すると、これまで用いてきたPID制御用定数群を該選択したPID制御用定数群に変更し、該選択したPID制御用定数群に含まれる各定数を用いて、ヒーター17をオンオフ制御し、温水の温度をPID制御する。 - 特許庁
When elapsed time from OFF of the main switch 43 to the next ON is relatively long, a solid polymer membrane in a fuel cell is considered as being in a more dried state, and since a second reference voltage LVL2 is changed, appropriate battery check is made possible even when voltage immediately after ON of a power source switch is varied by a humidified state.例文帳に追加
さらに、メインスイッチ43がOFFされてから、次にONされるまでの経過時間が比較的長い場合には、燃料電池内の固体高分子膜がより乾燥した状態にあるとして、第2の基準電圧LVL2を変更するので、加湿状態によって電源スイッチON直後の電圧が変動する場合でも、適切なバッテリチェックが可能となる。 - 特許庁
To develop an electrolyte membrane enhancing joining property to a catalyst electrode layer, and even when a fuel cell is used under a severe using condition such as high temperature for a long time, capable of greatly reducing peeling off of the catalyst electrode layer, in the fuel cell using a solid polymer electrolyte membrane made of crosslinked anion-exchange resin.例文帳に追加
架橋型の陰イオン交換樹脂からなる固体高分子電解質膜を用いた燃料電池において、触媒電極層との接合性をさらに向上させ、燃料電池の使用が高温下等の過酷な使用環境で長期間に及んだとしても、該触媒電極層の剥離が大幅に低減可能なものにできる、該電解質膜を開発すること。 - 特許庁
To provide an operating device and an image forming device for saving on power of the device by turning off a display part at the time of operation other than when it is required to display information during operation, and extending the service life of a liquid crystal display element and illumination for a liquid crystal display used for a display unit.例文帳に追加
本発明は、動作中に情報を表示する必要がある場合を除き動作時には表示部をOFFすることにより装置の省電力化を図り、表示部に用いた液晶表示素子及び液晶表示用の照明の寿命を延ばすことができる操作装置及び画像形成装置を提供することを目的とする。 - 特許庁
To shorten the time required for link establishment, to easily adjust trade-off between enhancement of detection precision and generation of misdetections, to promote miniaturization, cost reduction of device, to detect a signal such as a call signal and to correct carrier frequency deviation, with respect to call termination deciding technology under radio environment, in which the reception status of the signal is poor.例文帳に追加
信号の受信状態が劣悪の無線環境下における着信判定技術であって、リンク確立に要する時間を短縮し、検出精度の向上と誤検出の発生とのトレードオフを容易に調整でき、また、装置の小型化,低廉化を促進でき、そして、呼び出し信号等の信号検出とキャリア周波数偏差の是正を可能にする。 - 特許庁
The remote control apparatus 51 for the video apparatus (video recorder) 50 for supplying a video source to the television receiver 10 provided with the non-operation off-timer for interrupting power when receiving no operation signal for a prescribed time includes a control section 54 that allows a signal output section 57 to transmit an operation signal to the video recorder when a key operation section 52 is operated.例文帳に追加
所定時間の間操作信号が入力されないと電源をオフにする無操作オフタイマを備えたテレビ受信機10に対し、映像ソースを提供するビデオレコーダー50のリモートコントロール装置51において、キー操作部52が操作されるとその操作信号を信号出力部57により送信させる制御部54とを備える。 - 特許庁
To provide a hand and arm cover smoothly put on and off without depending on the elasticity of a knit product or the elasticity of a material itself such as leather by forming an elastic region in the hand and arm cover, having good operability or the like without imparting feeling of pressure to a user even after being worn for a long time, and also having excellent fashionability.例文帳に追加
手腕被覆体に伸縮領域を設けることによって、編物製品の伸縮性又はレザー等の素材自体の伸縮性に頼らずとも、着脱がスムーズで長時間装着しても使用者に圧迫感を与えず作業性等が良好で、且つファッション性に優れた手腕被覆体を提供することを目的とする。 - 特許庁
A function for controlling a tunnel outside lighting circuit is added to a control part 2 having a function for controlling a tunnel light part 4 installed outside a tunnel and connected to a light receiving device 1 for measuring brightness, and the tunnel outside lighting circuit is controlled with on-off time previously set and a brightness value measured with the light receiving device 1.例文帳に追加
トンネル外に設置される輝度を測定するための受光器と接続されたトンネル照明を制御する機能を備えた制御部に、坑外照明回路を制御する機能を付加し、坑外照明回路の制御を、予め設定されたON−OFFする時刻と、受光器により測定される輝度値の両方を用いて行う。 - 特許庁
To provide a video image output system by which power saving is attained by controlling the turn-on/off of power supply according to whether or not a video image from a reproduction device is selected and the video image is displayed in a shorter period of time when the video image of television broadcast is selected, and a television receiver used in the video output system.例文帳に追加
再生装置からの映像が選択されているか否かに応じて電力の供給のオン/オフを制御して省電力を実現し、テレビジョン放送の映像が選択された場合に、より短い時間で映像を表示することができる映像出力システム及び映像出力システムで用いるテレビジョン受像機を提供する。 - 特許庁
Furthermore, in the CPU 23a, when the overcurrent state continues throughout a predetermined time, it is determined that a short-circuiting failure has occurred in a solenoid driving circuit 23c inputting a control signal Ls into the solenoid 106a, and flowing of the short-circuit current through the solenoid 106a is prevented by cutting off a direct-current power supply 26 and the solenoid driving circuit 23c.例文帳に追加
さらにCPU23aは、過電流状態が所定の時間に亘って継続したときには、ソレノイド106aに制御信号Lsを入力するソレノイド駆動回路23cに短絡故障が発生したと判定し、直流電源26とソレノイド駆動回路23cを遮断してソレノイド106aに短絡電流が流れることを防止する。 - 特許庁
When this storage system 2 receives data read request from a host computer 1 to a logic unit 28, the storage system 2 selects a logic device 27a reading data from a power status and power-OFF time of respective logic devices 27a, 27b allocated to the logic unit 28, controls the power source of the selected logic device 27a to turn on, and reads the data.例文帳に追加
ストレージシステム2は、ホスト計算機1から論理ユニット28へのデータ読み出し要求を受けると、論理ユニット28に割り当てられた各論理デバイス27a,27bの電源状態と電源オフ時刻とからデータを読み出す論理デバイス27aを選択し、選択された論理デバイス27aの電源をオンに制御してデータを読み出す。 - 特許庁
A carrier sense part 103 sets a carrier sense flag F1 when shut-off or interruption of the optical radio transmission line is discriminated, a mute part 108 gradually mutes a digital sound signal after processing of an ECC part 107 when the carrier sense flag F1 is set and entirely completes mute at the time when an error detection flag F2 from the ECC part is set.例文帳に追加
キャリアセンス部103は光無線伝送路の瞬断又は遮断を判別するとキャリアセンスフラグF1をセットし、ミュート部108はキャリアセンスフラグF1がセットされるとECC部107の処理後のデジタル音声信号を徐々にミュートし、ECC部からの誤り検出フラグF2がセットされた時点ではミュートを完全に完了する。 - 特許庁
In order to set the position for automatic adjustment, the optical pickup is instructed to stop movement at a position where it has moved further in the outer peripheral direction for a new prescribed time after the off-detection of the switch 7, and thereby the optical pickup 2 can be located at an optimal position for automatic adjustment even in a temperature environment that is different from a standard.例文帳に追加
自動調整対象位置を設定するため、スイッチ7のオフ検出開始から新たな所定時間だけ、さらに外周方向へ移動した位置において光ピックアップの移動を停止する指示をすることにより、標準と異なる温度環境下においても光ピックアップ2を最適な自動調整対象位置に配置することができる。 - 特許庁
When any of the cooling water temperature THW ≤ THWh ("NO" in S182), the upstream side exhaust temperature Texin ≤ Texh ("NO" in S184) or the downstream side exhaust temperature Texout ≤ Texh ("NO" in S186) is realized, "OFF" is set in a catalyst activation stable time flag Fcat as the air-fuel ratio varying timing (S194).例文帳に追加
冷却水温THW≦THWh(S182で「NO」)、上流側排気温Texin≦Texh(S184で「NO」)あるいは下流側排気温Texout≦Texh(S186で「NO」)のいずれかが成立すれば、空燃比変動時期であるとして触媒活性安定時フラグFcatに「OFF」を設定している(S194)。 - 特許庁
A data voltage corresponding to a gradation signal supplied to the data line 8 is written into a retention capacitance 7 via the coupling capacitance 6, at the same time, the reset transistor 4 is turned on while the selective transistor 3 and the light emission control transistor 5 are turned off and a correction voltage in accordance with mobility of the driving transistor 2 is written into the coupling capacitor.例文帳に追加
データライン8に供給される階調信号に対応するデータ電圧をカップリング容量6を介し、保持容量7に書き込むとともに、選択トランジスタ3および発光制御トランジスタ5をオフとした状態でリセットトランジスタ4をオンして駆動トランジスタ2の移動度に応じた補正電圧を前記カップリングコンデンサ6に書き込む。 - 特許庁
At the time of electrode-closing operation to transit from a current cut-off state to an energized state, the gas containing the decomposed material in the gas chamber 35 passes through a peripheral wall 31b composed of a porous material of a sucking cylinder 31, and after the decomposed material is removed by contacting an adsorbent 40 arranged into its surroundings is released in the sealed container.例文帳に追加
電流遮断状態から通電状態に移行する閉極動作時には、ガス室35内の分解物質を含むガスは、吸い込みシリンダ31の多孔質材料からなる周壁31bを通過し、その周囲に配置された吸着剤40に接触して分解物質が除去された後、密閉容器内に放出される。 - 特許庁
Her father Tadamasa also held a territory in Mikawa Province near Ogawa, and upon the request of Kiyoyasu MATSUDAIRA who held a great deal of power in Mikawa at the time, he made Otomi no Kata divorce and marry Kiyoyasu but his desire to further strengthen his relationship with the Matsudaira clan led him to marry off his daughter Odai in 1541 to Hirotada MATSUDAIRA who succeeded Kiyoyasu. 例文帳に追加
父・忠政は緒川からほど近い三河国にも所領を持っており、当時三河で勢力を振るっていた松平清康の求めに応じて於富の方を離縁して清康に嫁がせたが、松平氏とさらに友好関係を深めようと考え、天文10年(1541年)に娘の於大を清康の後を継いだ松平広忠に嫁がせた。 - Wikipedia日英京都関連文書対訳コーパス
A clock device 1 is provided on a vehicle having a navigation device and GPS time information B is extracted out of GPS information signal input from a GPS antenna 12 by a data analyzer circuit 16 provided in a GPS receiver 14 and an off-set value A is set by the operation of an input device 20.例文帳に追加
本発明の実施例の時計装置1は、ナビゲーション装置を備えた車両に設けられており、GPSアンテナ12から入力されるGPS情報信号の中から、GPS受信機14に備えられたデータ解析回路16によりGPS時刻情報Bが抽出され、入力装置20の操作によりオフセット値Aが設定される。 - 特許庁
An address setting part sets a first address information showing address information of the illumination device which controls a state in the timing of brightness changes and a second address information showing address information related to the illumination device which controls a state in the timing off-set by a set time with the timing of brightness changes as a reference.例文帳に追加
アドレス設定部は、明るさ変化のタイミングにおいて状態制御を行う照明装置のアドレス情報を示す第1のアドレス情報と、明るさ変化のタイミングを基準として設定時間だけオフセットさせたタイミングにおいて状態制御を行う照明装置に関するアドレス情報を示す第2のアドレス情報とを設定する。 - 特許庁
In this video viewing system in which server devices such as a tuner unit and a video server and a plurality of video terminals such as receivers are mutually connected via a network, when the user starts viewing by supplying the power to the video terminals (receivers) sides, user's convenience is improved by automatically reproducing the connection state at the time when the power is previously turned off.例文帳に追加
チューナーユニットやビデオサーバー等のサーバー機器、および複数の受像機等の映像端末などが相互にネットワークで接続された映像視聴システムにおいて、映像端末(受像機)側の電源投入操作により、ユーザーが視聴を開始する際に前回電源切断時の接続状態を自動的に再現する事により、ユーザーの利便性を図る。 - 特許庁
The optical system within a UV light observation casing 16 including all of the illumination optical system and the observation optical system can be evaded from the irradiation with the ultra-UV light by closing a shutter 4 and the contamination of the surfaces of the optical members can be retarded only by the operation to close the shutter 4 without putting off the light source each time.例文帳に追加
照明光学系および観察光学系のすべてを内包する紫外光観察筐体16内部の光学系は、シャッタ4を閉じることにより極紫外光の照射から免れることができ、逐一光源の消灯をすることなく、単にシャッタ4を閉じる動作のみで、光学部材の表面の汚染を遅らせることができる。 - 特許庁
To provide a waste rubber-made curb block related to mass consumption of used tires as an effective use of the used tires reusing them for the waste rubber-made curb block and, at the same time, smoothly draining off rain water stagnated on the road by boring a drain outlet therein to eliminate execution of work of the drain outlet.例文帳に追加
使用済みタイヤの大量消費につながる廃ゴム製縁石ブロックとして再利用することで使用済みタイヤの有効利用を図るとともに、内部に排水孔を設けて路面上に溜まった雨水をスムースに排水するとともに、排水孔の施工工事を無くするようにした廃ゴム製縁石ブロックを提供することを目的とする。 - 特許庁
At a command to switch the load feed from the output of the inverter 12 to the bypass input power supply, the switching control means 2 starts phase control means 28 for the semiconductor switch 15 and outputs an off command to the first mechanical switch 13, and a predetermined time later, outputs an on command to the second mechanical switch 14.例文帳に追加
切換制御手段2は、負荷への給電をインバータ12の出力からバイパス入力電源側に切換える指令を受けたとき、半導体スイッチ15の位相制御手段28を開始すると共に第2の機械式スイッチ13にオフ指令を出力し、所定時間経過後に第1の機械式スイッチ14にオン指令を出力する。 - 特許庁
| 本サービスで使用している「Wikipedia日英京都関連文書対訳コーパス」はWikipediaの日本語文を独立行政法人情報通信研究機構が英訳したものを、Creative Comons Attribution-Share-Alike License 3.0による利用許諾のもと使用しております。詳細はhttp://creativecommons.org/licenses/by-sa/3.0/ および http://alaginrc.nict.go.jp/WikiCorpus/ をご覧下さい。 |
| Copyright © Japan Patent office. All Rights Reserved. |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|