| 意味 | 例文 |
Input valueの部分一致の例文一覧と使い方
該当件数 : 7753件
To provide an in-vehicle charging/discharging controller having a battery that accumulates power generated in a motor by regeneration, the battery being configured to efficiently accumulate energy when a battery temperature becomes equal to or higher than the upper limit thereof, in battery limit enhancement control which lowers the upper limit of input/output power below a normal value.例文帳に追加
回生によってモータが発電する電力をバッテリが蓄積する車載充放電制御装置において、バッテリ温度が上限バッテリ温度以上となった場合に入出力電力の上限を通常の値よりも低下させるバッテリ制限強化制御を行う場合、バッテリが効率的にエネルギーを蓄積できるようにする。 - 特許庁
In the meantime, a control amount calculation unit 34 calculates a control amount of a spherical surface ultrasonic motor of the each drive portion by position and posture data calculated by the position posture calculation unit 29 and position and posture data at the tip of the manipulator 9 inputted by a command value input unit 28, and supplies it to the motor.例文帳に追加
一方、位置姿勢算出手段29で算出した位置姿勢データ、指令値入力装置28で入力されたマニピュレータ9の先端部の位置姿勢データを用いて、制御量算出手段34において各駆動部の球面超音波モータの制御量を算出しモータへ供給する。 - 特許庁
When allowing the compression encoding means 100 to generate the inter-encoding data 24ter, a control means 200 sets a code amount not more than a maximum code amount which is given by a multiplication value between an upper limit transmission rate of the transmission line and an allowed time assigned per image based on an image rate of the input moving image.例文帳に追加
制御手段200は、圧縮符号化手段100にインター符号化データ24terを生成させる場合、伝送路の上限伝送レートと、入力動画像のピクチャレートに基づいて1ピクチャ当たりに割り当てられる許容時間との乗算値で与えられる最大符号量以下の符号量を設定する。 - 特許庁
When the input voltage Vi falls below 95 V, that is, when the lowering of the voltage at the charging cable is large, an upper-limit value P_max of an output voltage Po to the battery is lowered since there is an anxiety of an increase of wiring resistance in the charging cable (steps S14, S16 and S17).例文帳に追加
入力電圧Viが95Vを下回る場合、つまり充電ケーブルでの電圧の落ち込みが大きい場合には、充電ケーブルにおける配線抵抗の増大が懸念されるため、バッテリに対する出力電力Poの上限値P_maxが引き下げられる(ステップS14,S16,S17)。 - 特許庁
Then, the CPU 21a determines load difference ΔF between the load when the effect exists corresponding to a motor current value I supplied to the electric actuator 13 at present and the load when the effect has become unworkable, and adds the load difference ΔF to a detected load F input from a load sensor 22 for correction.例文帳に追加
次に、CPU21aは、現在、電動アクチュエータ13に供給しているモータ電流値Iに対応して前記効果が発生している場合の荷重と前記効果が無効化した場合の荷重との荷重差ΔFを決定し、この荷重差ΔFを荷重センサ22から入力した検出荷重Fに加算して補正する。 - 特許庁
Then, the phase comparator 13 is connected to the DLL loop by the switching circuit 15 at a timing of rise edge of the input clock CLK1, the number of steps of delay cells of the first variable delay circuit 11 is set at the number of steps corresponding to a counter value of the counter 14, and a usual DLL locking operation is performed.例文帳に追加
そして、入力クロックCLK1の立上りエッジのタイミングで、切換回路15により位相比較器13をDLLループに接続するとともに、カウンタ14のカウンタ値に相当する段数に、第1可変遅延回路11の遅延セル段数を設定してから、通常のDLLロック動作を行わせる。 - 特許庁
A multifunctional machine displays a list screen on which a plurality of setup items is arranged on liquid crystal display, specifies one of the setup items on the list screen to make a focusing state, and selects the focused setup item to make a selection state permitting accepting input of a setup value in response to pressing of an OK key.例文帳に追加
複合機は、設定項目が複数配列されたリスト画面を液晶ディスプレイに表示し、リスト画面において1つの設定項目を指定してフォーカス状態とし、OKキーが押下されることに応じて、フォーカス状態にある設定項目を選択して設定値の入力を受け付け可能な選択状態にする。 - 特許庁
A back-light control unit 304 determines a target luminance of a back light from input image data Din, and generates an intermediate luminance using a nonlinear function NLF decreasing in variation amount with time to vary the luminance of the back light when the difference between the current luminance of the back light and the target luminance is equal to or larger than a predetermined value.例文帳に追加
バックライト制御部304は、入力画像データDinからバックライトの目標輝度を決定し、バックライトの現在の輝度と目標輝度との差が所定値以上の場合は、時間の経過に応じて変化量が減少する非線形関数NLFを使用して中間輝度を生成し、バックライトの輝度を変化させる。 - 特許庁
A polynomial approximation expression is created based on a focus map of a previously measured optical microscope, and a control amount derived from the polynomial approximation expression by adding thereto wafer height information at creation time and a difference between it and another wafer height information at actual observation time is input as a focus control value for the optical microscope.例文帳に追加
予め測定された光学式顕微鏡のフォーカスマップを基に多項式近似式を作成し、その時のウエハ高さ情報と、実際の観察時におけるウエハ高さ情報との差分を前記多項式近似式に加算した制御量を光学式顕微鏡のフォーカス制御値として入力する。 - 特許庁
Thus, the smooth function parameter δ is set based upon the steady-state deviation limit σ_e and input variation maximum value d_max using the σ-u_nl coordinates to logically set the smooth function parameter δ, and tuning results and tuning man-hours less vary with operators.例文帳に追加
このように、平滑関数パラメータδを、σ−u_nl座標を用いて定常偏差限界σ_eと入力変動最大値d_maxとに基づいて設定することで、平滑関数パラメータδを理論的に設定することが可能となり、作業者によるチューニング結果やチューニング工数のばらつきを低減することができる。 - 特許庁
In a control section 20 of this collision damage relieving device 2, a TTC computing section 22 computes the collision estimated time (TTC) based on information input from a monitor sensor 11, and a first determining section 23 determines whether the level of possibility that an object and a vehicle collide with each other is a third level (TTC ≤ first threshold value time) or not.例文帳に追加
衝突被害軽減装置2の制御部20では、監視センサ11からの入力情報に基づいて、TTC算出部22が衝突予測時間(TTC)を算出し、第1判定部23が、対象物と車両との衝突可能性のレベルが第3レベル(TTC≦第1閾値時間)であるか否かを判定する。 - 特許庁
In the game machine 100, which can display an expectation value for a jackpot on a display performance symbol display apparatus 30 depending on the operation frequency to the performance button 46, the timing or the period of time in which the operation to the performance button 46 is effective is reported to the game player by the light emission by an external input unit 330.例文帳に追加
演出ボタン46に対する操作回数によって大当たりの期待値を表示演出図柄表示器30に表示可能な遊技機100における演出ボタン46への操作が有効であるタイミングないし期間を、外部入力手段330での発光によって遊技者に報知する。 - 特許庁
An element value of at least one kind of element 3, which determines a filter characteristic of this filter circuit 2, is varied based on the output of a ΣΔ modulator 1, which sigma-delta modulates a digital code input (Code) based on an operation clock CLK, or a signal through a decoder 4 which performs a code-conversion to the output of the ΣΔ modulator 1.例文帳に追加
フィルタ回路2のフィルタ特性を決定する少なくとも1種の素子3の素子値を、動作クロックCLKに基づきデジタルコード入力Codeをシグマデルタ変調するΣΔ変調器1の出力、或いは該ΣΔ変調器1の出力をコード変換するデコーダ4を介した信号に基づき変化させる。 - 特許庁
Hence, front-back pitching vibration or a shock load input in the front-back direction by back collision and the like which is larger than a predetermined value works as a force in a direction for bending the back frame in the right-left direction and thus a vibration-shock energy is consumed and, in addition, the vibration-shock energy is consumed by displacing the back frame backward further.例文帳に追加
従って、前後・ピッチング振動、あるいは、後突等により前後方向に入力された所定以上の衝撃荷重は、バックフレームを左右に撓ませる方向への力となるため、それによって振動・衝撃エネルギーが消費され、さらに、バックフレームを後方に変位させることによって振動・衝撃エネルギーが消費される。 - 特許庁
The input position is calculated on the basis of a position of a specific magnetic sensor having a maximum detected value out of the set of magnetic sensors defining the specific region and detected values A(m, n), A(m-1, n), A(m+1, n), A(m, n-1), and A(m, n+1) of the set of magnetic sensors defining the specific region.例文帳に追加
特定領域を区画する一組の磁気センサのうちで検出値が最大である特定の磁気センサの位置と、特定領域を区画する一組の磁気センサの検出値A(m,n)、A(m−1,n)、A(m+1,n)、A(m,n−1)、A(m,n+1)とに基づいて入力位置を算出する。 - 特許庁
To provide an image forming apparatus which controls toner refilling in combination of pixel refilling control and sensor refilling control, to calculate the upper limit value of an appropriate amount of toner even when desired image processing is performed for input image data and an image is formed based on the image data subjected to image processing.例文帳に追加
画素補給制御とセンサ補給制御とを組み合わせたトナー補給制御を行う画像形成装置において、入力画像データに対し、所望の画像処理を施し、その画像処理後の画像データに基づいて画像形成を行う場合でも、適切なトナー補給量の上限値を算出する。 - 特許庁
Thereby, the electro-optical device can display the highly precise image because each data value of the input image data Da can be assigned to be within an expected impression voltage range even if several kinds of liquid crystal display panels 100A, 100B that have different V-T characteristics and an image signal processing circuit 300A are combined.例文帳に追加
これにより、V−T特性の異なる複数種類の液晶表示パネル100A、100Bと画像信号信号処理回路300Aを組み合わせても、入力画像データDaの各データ値を所望の印加電圧範囲に割り当てることができるから、高精細な画像を表示することが可能となる。 - 特許庁
The automatic gain control device includes signal amplitude adjustment means 1 for outputting an amplified or attenuated input signal, and signal processing means 10 for determining a gain or attenuation value in accordance with an output of analog-digital conversion means 2 for converting the output signal of the signal amplitude adjustment means 1 to a digital signal.例文帳に追加
入力信号を増幅または減衰して出力する信号振幅調整手段1と、信号振幅調整手段1の出力信号をデジタル信号に変換するアナログデジタル変換手段2の出力に基づき利得または減衰値を決定する信号処理手段10とを備える。 - 特許庁
And a controller 21 that processes information setting for checking variations in characteristics outputs a currently detected angular speed detected by the angular speed detector 23 and an initial detected angular speed meeting the conditions of detection for this detected value to a checkup device 30 via an input/output interface 25.例文帳に追加
そして、上記特性変化検査用情報設定処理を実行する制御部21により、角速度検出部23により検出される現角速度検出値とこの検出値の検出条件に対応する初期角速度検出値とが入出力インタフェース25を介して検査装置30に出力される。 - 特許庁
A result image data compression part 5 performs the same arithmetic processing as that to the expected value image data to result image data generated by an image processing circuit 11 that is a verification object according to the input pattern data 21 to thereby generate result image compression data smaller in size than the result image data for each page of the moving image.例文帳に追加
入力パターンデータ21に応じて、検証対象の画像処理回路11により結果画像データを生成し、結果画像データ圧縮部5により、期待値画像データに対するのと同じ演算処理を行って、動画像の1ページ分ずつ、結果画像データよりもサイズの小さい結果画像圧縮データを生成する。 - 特許庁
When generating the test data including a pair of an input (a combination between a factor and a level) and an expectation value, a combination between the inputs not but combinations between all the levels possible to the factor is generated such that each of all the levels in each factor is used in a test at least once.例文帳に追加
本発明は、入力(因子と水準の組み合わせ)と期待値のペアからなるテストデータを生成する際に、因子に対して、有り得る全ての水準の組み合わせではなく、各因子における全ての水準が少なくとも1回はテストで使用されるように、入力の組み合わせを生成する。 - 特許庁
To provide an efficient image forming method which achieves the lower electric power, lower calorific value, higher-speed reading and lower noise of high-density silver halide color photographic sensitive materials of which the processing is ended in the state of having silver halide and developing silver and an image input device useing the same.例文帳に追加
本発明の目的は、ハロゲン化銀及び現像銀を有する状態で処理を終了させた、高濃度のハロゲン化銀カラー写真感光材料の省電力化、低発熱量、高速読み取り及び低ノイズ化を達成する効率的な画像形成方法とそれに用いる画像入力装置を提供することにある。 - 特許庁
A clock frequency of the modulator is set to a value of constant multiples of a clock signal of an original signal which should be transmitted before modulation, bit length of input data is extended to the same magnification as that of the clock frequency inside the modulator, and a dummy signal with a different logic is mixed with "0" or "1" before the modulation to be transmitted.例文帳に追加
変調器のクロック周波数を変調前の伝送すべきオリジナル信号のクロック周波数の定数倍の値に設定し、変調器内部で入力データのビット長をクロック周波数と同じ倍率に拡張し、変調前の“0”あるいは“1”に対して論理の異なるダミー信号を混合させて送信する。 - 特許庁
The system is equipped with a serial number input means which inputs the serial number of a magnetic head to magnetic characteristic inspection devices 1 and 2 arranged between the processes and transfers measured data and the inputted number to a host computer 4 while making them to correspond to each other; and the quantity of deviation in magnetic characteristic value between the processes is computed to make the propriety decision.例文帳に追加
工程間に配置された磁気特性検査装置1及び2に磁気ヘッドのシリアル番号を入力するシリアル番号入力手段を備え、計測したデータと、入力したシリアル番号とを対応させてホストコンピュータ4に転送し、各工程間での磁気特性値の変位量を計算して良否の判定を行う。 - 特許庁
The drive system sets a value obtained by converting a transfer delay angle for an input of a first and a second drive transfer mechanisms 4, 5 into a rotating angle of a shaft 1a of the stepping motor 1, so as to become larger than a rotating angle M generated for correction of phase deviation which is conducted when the stepping motor 1 is driven to rotate.例文帳に追加
駆動システムは、第1及び第2の駆動伝達機構4、5の入力に対する伝達遅れ角度をステッピングモータ1の軸1aの回転角度に換算した値が、そのステッピングモータ1の回転起動に際して行われる位相ずれの修正時に発生する回転角度Mよりも大きくなるように設定する。 - 特許庁
This non-contact information input device is configured to detect the hand 8 of a user by an imaging means 1, and to select an operation mode from the shape of the hand 8, and to detect a distance from the hand 8 to the imaging means 1 as for a parameter to be adjusted, and to adjust the value of the parameter according to the distance.例文帳に追加
撮像手段1で使用者の手8を検出し、手8の形状から操作モードを選択し、かつ、調整すべきパラメータについては、手8から撮像手段1までの距離を検出し、その距離に応じてパラメータ値の調整を行うように構成した非接触式情報入力装置。 - 特許庁
Depending on an input value N for a numeric number for specifying in how many columns of the first analysis schedule table all analysis for the second analysis schedule table is inserted, numbers of insertion for continuous analysis are calculated, and total numbers of analysis T are calculated from the numbers of insertion and N1, N2 (S12) and displayed on a screen (S2).例文帳に追加
そして、第2の分析スケジュールテーブル中の全分析を第1の分析スケジュールテーブル中の何行毎に挿入するかを指定する数値の入力値Nに応じて、連続分析中の挿入回数を計算し、その挿入回数とN1、N2とから総分析回数Tを算出して(S12)画面上に表示する(S2)。 - 特許庁
This TA counter 35 is a well-known hardware AB-phase pulse counter and has a function of increasing/decreasing a counter value in each pulse cycle with respect to the input of the A-phase and B-phase pulse signals, and two of each-phase pulse signals Pu, Pv and Pw, outputted by a rotating angle sensor 26, are inputted into the TA counter 35.例文帳に追加
このTAカウンタ35は、周知のハードウェアAB相パルスカウンタであり、A相及びB相パルス信号の入力に対して、そのパルス周期毎にカウンタ値を増減する機能を有し、同TAカウンタ35には、回転角センサ26が出力する各相パルス信号Pu,Pv,Pwのうちの二つが入力される。 - 特許庁
A signal correction unit 21 corrects the grayscale value of the video signal Gr on the basis of the difference for each display pixel 15 stored in the second storage unit 20 until the input of the video signal Gr ends, so that an image with unevenness of luminance corrected can be displayed on a display unit 14.例文帳に追加
以降、映像信号Grの入力が終了するまで、第2記憶部20に記憶された表示画素15毎の差分に基づいて、信号補正部21にて、映像信号Grの階調値の補正を行うことにより、輝度のムラが抑制された画像を表示部14に表示させることが出来る。 - 特許庁
The evaluation device 20 comprises a circuit element 24 comprising respective pairs of inputs and outputs including several capacitances 25a-25c and resistances 26a-26d, one end of each being connected to both ends of the capacitances 25a-25c, wherein a resistance value of a signal input side is nearly equal to that of a signal output side.例文帳に追加
評価装置20に、幾つかの容量25a〜25cと容量25a〜25cの両端に対して各々の一端が接続されている抵抗26a〜26dとを含む夫々1対の入出力を有していて、信号入力側の抵抗値と信号出力側の抵抗値とが略同一である回路素子24を備える。 - 特許庁
The arithmetic processing based on the configuration data of the user control data to be executed as the generation processing of the cipher key is configured by a unidirectional function, Reed-Solomon code calculation, cyclic redundancy code calculation processing, etc., by which the configuration including the function to make it difficult to determine the arithmetic input value from the result of the mathematical operation is obtained.例文帳に追加
暗号鍵の生成処理として実行するユーザ制御データの構成データに基づく演算処理は、一方向性関数、リード・ソロモン符号算出、巡回冗長符号算出処理などによって構成され、演算結果から演算入力値を求めるのが困難な関数を含む構成とした。 - 特許庁
A threshold value generator circuit 40 is controlled by a control unit 41 and generates various voltage threshold values, an input signal and the voltage threshold values are fed to a comparator circuit 37, the comparison result is fed to a circuit part 38 connected successively, and various operations are performed in the circuit part depending on the comparison result.例文帳に追加
閾値発生器回路40は制御ユニット41によって制御されて、種々の電圧閾値を発生し、入力信号と電圧閾値は比較器回路37に供給され、比較結果は後に接続された回路部分38に供給され、これらの回路部分において、比較結果に依存して種々の動作が行なわれる。 - 特許庁
In the same way, a score S2 for indicating likelihood of a music/background-sound-superimposed signal, by calculating various feature parameters for discriminating between music and a background-sound-superimposed voice signal, from the input audio signal, and by attaching the weight coefficient based on the parameter value of the reference data for the music/background sound.例文帳に追加
同様に、入力オーディオ信号から音楽と背景音の重畳した音声信号とを判別するための各種の特徴パラメータを算出し、音楽・背景音用参照データのパラメータ値に基づく重み係数を付与し、音楽・背景音重畳音声信号の確度を表すスコアS2として算出する。 - 特許庁
The end of the torque-reduction control is determined on the basis of whether a deviation (D2-D1) between a difference D2 between the last engine speed NE and the turbine rotating speed NT and a difference D1 between the engine speed NE in a start of fastening of the input clutch and the turbine rotating speed NT is larger than a regulation value N2 or not.例文帳に追加
前記トルクダウン制御の終期は、最新のエンジン回転速度NEとタービン回転速度NTとの差D2と、入力クラッチの締結開始時におけるエンジン回転速度NEとタービン回転速度NTとの差D1との偏差(D2−D1)が規定値N2よりも大きいか否かに基づいて判断する。 - 特許庁
With two relays in a first relay device 13 disconnected, a capacitor step-up converter 15 is controlled so that the difference between the output voltage V_FC of a fuel cell 11 and the voltage V_L1 across an input smoothing capacitor 16 is reduced to a predetermined threshold value E_TV or below (Steps S103 to S105).例文帳に追加
第1のリレー装置13内の2個のリレーが切断されている状態において、燃料電池11の出力電圧V_FCと入力平滑キャパシタ16の両端の電圧V_L1との差が所定の閾値E_TV以下に低減されるようキャパシタ昇圧コンバータ15が制御される(ステップS103〜S105)。 - 特許庁
The nonvolatile semiconductor memory device has a memory cell array 1 using electrically rewritable NAND cells, a column decoder 4, a bit line control circuit 2, a word line control circuit 6, and a data input/output buffer 4, wherein previous writing and confirmation reading are performed after batch erasing of data to put erased memory cells into a desired threshold-value range.例文帳に追加
電気的書き換え可能なNAND型セルを用いたメモリセルアレイ1、カラムデコーダ4、ビット線制御回路2、ワード線制御回路6、データ入出力バッファ4を有し、データの一括消去後に事前書き込みと確認読み出しを行って消去されたメモリセルを、所望のしきい値範囲に追い込むようにした。 - 特許庁
Even if the information, relating to the voltage setting which is set as the output voltage to the outside device for the supply, is different from the voltage value as actually needed according to the first voltage setting information input from the outside, desired output voltage can be set by flexibly adjusting the actual voltage information.例文帳に追加
外部から入力される第1電圧設定情報により、供給先である外部装置への出力電圧として設定されている電圧設定に関する情報が、実際に必要とされる電圧値とは異なる場合にも、実電圧情報を柔軟に調整して所望の出力電圧を設定することができる。 - 特許庁
In a temperature control circuit which controls the quantity and the direction of a current to be supplied to a control device 109 by using a square pulse wave, a signal from an absolute value calculation circuit is taken as an input to make a voltage applied to the control element 109 variable, thereby reducing the power supply.例文帳に追加
制御素子109に供給する電流の量および方向を矩形パルス波により制御する温度制御回路において、絶対値演算回路からの信号を入力として制御素子109に印加する電圧を可変することにより供給電力を小さくできる構成とした。 - 特許庁
This display device is constituted so that a counter electrode potential Vcom corresponding to the interval between a picture signal wiring S1 and a picture signal wiring S3072 has an inclination between the input edge side and the termination side of the scanning signal based on an optimum counter electrode potential to be obtained by a flicker minimum value deciding method.例文帳に追加
フリッカー最小値決定法で求められる最適対向電極電位に基いて、走査信号の入力端側と終端側との間、ここでは画像信号配線S1と画像信号配線S3072との間、に対応する対向電極電位Vcomに傾斜を持たせるように構成する。 - 特許庁
The microcomputer further includes a second control signal output part 31B which outputs the control signal Smc_b to the drive circuit 26B of the second system by executing positional control on the basis of a steering angle command value θs* input from a superior ECU via an in-vehicle network so as to change the steering angle of the steering road wheels.例文帳に追加
そして、更に、転舵輪の舵角を変更すべく車内ネットワークを介して上位ECUから入力される操舵角指令値θs*に基づいて、位置制御を実行することにより第2系統の駆動回路26Bに対して制御信号Smc_bを出力する第2制御信号出力部31Bを備える。 - 特許庁
The transmission apparatus is called at a constant processing period (tpc), receives analog information (S110), detects the change in the analog data received this time and newest transmission data stored in a transmission data memory 8 from the difference between both data (S120), and uses the detected change for an input value to decide a transmission interval (S130).例文帳に追加
処理周期(tpc)で定周期呼び出しされ、アナログ情報を入力し(S110)、入力した今回のアナログデータと送信データ用メモリ8に格納されている最新の送信データとの変化量を両者の差分から検出し(S120)、検出された変化量を入力値として送信間隔を決定する(S130)。 - 特許庁
An N-bit up/down counter 1 counts a period of a PWM input 21 for generating a deviation value from the 50% of a duty as control command data 33, a determination signal having not less or not more than the 50% of the duty is generated by an underflow signal for outputting as an acceleration or deceleration command of the drive circuit of a brushless motor.例文帳に追加
PWM入力21の周期をNビットアップダウンカウンタ1でカウントしてデューティが50%からの偏差値を制御指令データ33として生成し、アンダーフロー信号によりデューティが50%以上か以下かの判定信号を生成し、ブラシレスモータの駆動回路の加速指令または減速指令として出力する。 - 特許庁
The liquid crystal display device is equipped with a voltage supply means for discretely supplying a voltage of a prescribed voltage value in addition to the gray scale voltage supplied from a source electrode to each of the plurality of the sub-pixels within the unit pixel, and a means (input signal decision section 2) for detecting the movement level of the video displayed on the liquid crystal display panel 8.例文帳に追加
単位画素内の複数の副画素それぞれに対し、ソース電極から供給の階調電圧に加え、所定電圧値の電圧を個別に供給する電圧供給手段と、液晶表示パネル8に表示している映像の動きレベルを検出する手段(入力信号判定部2)を備える。 - 特許庁
Two input signals I and Q, whose phases cross orthogonally to each other, are inputted to a first multiplier 21 and a second multiplier 22 and multiplied by a tangent value tan α of a desired phase, the signal I is added to the output of the second multiplier 22, and an output of the first multiplier 21 is subtracted from the signal Q.例文帳に追加
互いに位相が直交する2つの入力信号I、Qを第1の乗算器21と第2の乗算器22に入力して所望位相の正接値tanαを乗算し、信号Iと第2の乗算器22の出力とを加算し、信号Qから第1の乗算器21の出力を減算する。 - 特許庁
A CPU 1 enables an SDRAM 2, which is for operating a common BOOT program 31 of a ROM 3, to operate by means of an SDRAM controller 11 and an operational frequency setting controller 12 based on RAM size information and an input clock frequency value which are both acquired in an IN order of an IN order circuit group 4.例文帳に追加
CPU1は、SDRAMコントローラ11と動作周波数設定コントローラ12により、INオーダー用回路群4のINオーダーで取得するRAMサイズ情報と入力クロック周波数値を元にしてROM3の共通BOOTプログラム31が動作するためのSDRAM2を動作可能とする。 - 特許庁
When updating XML data 24-i (1≤i≤n) held by a server 2, while using an update form display means 112, a client 1 displays an update form having input fields for inputting the position of an update target element, an update class and added or changed value in the XML data 24-i on a display device 14.例文帳に追加
クライアント1は、サーバ2が保持しているXMLデータ24−i(1≦i≦n)を更新する際、更新フォーム表示手段112を用いて、XMLデータ24−i中の更新対象要素の位置,更新種別,追加或いは変更後の値を入力するため入力欄を有する更新フォームを表示装置14に表示する。 - 特許庁
In a non-interactive temperature control method for the heating barrel of an extruder, an H∞ external turbulence observer composed of a transmission function Pmk(s) equal to the nominal value transmission function of control output yk and an H∞ controller is introduced from virtual input vk, to control the variation of a barrel temperature by the influences of external turbulence and model-conversion errors.例文帳に追加
押出成形機の加熱バレルの非干渉化温度制御方法において、仮想的入力v_k から制御出力y_k の公称値伝達関数に等しい伝達関数P_mk(s)とH∞制御器から構成されるH∞外乱オブザーバを導入し、外乱やモデル化誤差の影響によるバレル温度の変動を抑止する。 - 特許庁
This edge trigger type flip-flop circuit includes a pair of capacitors which are alternately charged and discharged up to the voltage approximate to the value of a supply line, joins a high or low impedance path to the input signal transition of prescribed polarity (e.g. a positive state) in combinations with a small number of switches and triggers the state change.例文帳に追加
本発明は、一対のコンデンサが供給線値に近い電圧まで交互に充放電され、また、少数のスイッチとの組み合わせで、予め決められた極性(たとえば、正の状態)の入力信号遷移に対してハイまたはローインピーダンスパスを与し、状態変化をトリガするエッジトリガ式フリップフロップ回路を提供する。 - 特許庁
When a gamma value for gamma compensation set in the liquid crystal projector is defined as γ, the drive signal setting process sets a signal level of each of the drive signals so that values produced by exponentiating, by a power 1/γ, the luminance levels of the output images of the liquid crystal panel at the time of having input each of the drive signals have nearly even intervals.例文帳に追加
駆動信号設定工程は、液晶プロジェクタに設定されるガンマ補正用のガンマ値をγとした場合、各駆動信号を入力した際の液晶パネルの出力画像の輝度値を指数1/γで累乗した値がほぼ等間隔となるように、各駆動信号の信号レベルを設定する。 - 特許庁
The switching control section 42 sets thresholds NLT of the number of revolutions and NHT of the generator 31 depending on the target value VT and connects each node of the windings 34a, 34b and 34c selectively to the input side of a rectifier circuit 3 along with the open end of the stator winding 34 based on the number of revolutions NG of the generator 31.例文帳に追加
そして、切換え制御部42は、その目標値VT に応じて発電機31の回転数しきい値NLT,NHTを設定し、発電機31の回転数NG に基づいて、巻線34a,34b,34cの各結節点を固定子巻線34の開放端と共に整流回路3の入力側に選択的に接続する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|