| 意味 | 例文 |
current sensorの部分一致の例文一覧と使い方
該当件数 : 3804件
A main CPU 31a measures the time from the input of the previous detection signal by the start winning hole sensor SE1 to the input of the current detection signal, compares the length of the measured time and predetermined time, and determines whether the detection signal is a regular one or irregular one.例文帳に追加
メインCPU31aは、始動入賞口センサSE1からの前回の検知信号の入力から今回の検知信号の入力までの時間を計測し、計測された時間とあらかじめ設定された所定時間との長短を比較して、検知信号の正規、不正規を判定する。 - 特許庁
The sensor output is compared with two difference threshold values Th1 and Th2 by comparison circuit 6 and 7 and, depending on the comparison results, a logic circuit 8 delivers an abnormal signal if the leak current is higher than the large threshold value Th1 and delivers a caution signal if it is between Th1 and Th2.例文帳に追加
センサ出力を比較回路6,7にて夫々大きさの異なる2つの閾値Th1,Th2と比較し、論理回路8は比較結果に応じて、漏れ電流が大きい閾値Th1より大きいとき異常信号、Th1以下Th2より大のとき注意信号を出力する。 - 特許庁
To create a vibration sensitive switch capable of being easily installed in an electric apparatus without requiring installing a controller part therein separately from a sensor part in the event that the function is installed therein of turning on/off a power current when the level of vibration imposed on the electric apparatus exceeds a threshold.例文帳に追加
電気機器に加わる振動レベルが閾値を超えたときに電源電流をオンしたりあるいはオフする機能を組み込むにあたって、センサ部とは別にコントローラ部を組み込む必要がなく、簡単に電気機器に組み込むことができる振動感応型スイッチを創作する。 - 特許庁
The control part computes a target position PP of the control point of the robot to position a characteristic point at the specific position within the visual field of the visual sensor based on the position relation data R considering a detected current position P of the control point as a position of the characteristic point of the workpiece.例文帳に追加
制御部は、検出された制御点の現在位置Pをワークの特徴点の位置とみなして上記の位置関係データRに基づいて、特徴点が視覚センサの視野内の特定位置に位置するようなロボットの制御点の目標位置PPを演算する。 - 特許庁
When a left curve is discriminated on the basis of a detection signal from a sensor, a current of a motor 16 on the inner wheel side out of lateral driving wheels 7, 8 supported on both sides of a bogie 12 is cut off to put the inner wheel in free rotation, and a conveying truck 1 travels only with the driving force of the outer wheel (Fig. (a)).例文帳に追加
搬送台車1はセンサからの検出信号に基づき「左カーブ」であると判別すると、ボギー12の両側に支持された左右の駆動輪7,8のうち内輪側のモータ16の電流を切って内輪をフリー回転にし、外輪の駆動力だけで走行する(同図(a))。 - 特許庁
To provide a method for precisely detecting an open failure of a resistor short-circuit switch even in a small current at which the detection of accuracy has been inferior in a conventional system, by reducing the number of times of uses of a detection sensor, with respect to the detection method of the open failure of a conventional resistor short circuit switch.例文帳に追加
従来の抵抗器短絡用スイッチ開放故障の検出方式に対して、検出用センサの使用数を減らし、かつ従来の方式では検出の精度が悪かった小電流においても、高精度で抵抗器短絡用スイッチの開放故障を検出する方法を提供する。 - 特許庁
The detection device comprises a first circuit 11 which connects a minus terminal of a battery 1 and a ground in series, a second circuit 13 which connects the minus terminal and a current sensor 12 and the ground in series, and a switching circuit 14 which selects either one of the first circuit 11 and the second circuit 13.例文帳に追加
バッテリ1のマイナス端子とアースとを直接に接続する第1回路11と、マイナス端子と電流センサ12とアースとを直列に接続する第2回路13と、第1回路11と第2回路13とのいずれか一方を選択するスイッチング回路14とを設ける。 - 特許庁
Next, the CPU 60 obtains the absolute value of a detected voltage Va from a development current sensor 64, and determines whether the chargeability of toner has been deteriorated or not by determining whether the absolute value of the obtained detected voltage Va is smaller than a first threshold preset in a ROM 61 (S125 to S145).例文帳に追加
そして、現像電流センサ64から検出電圧Vaの絶対値を取得し、取得した検出電圧Vaの絶対値が、ROM61に予め設定された第1の閾値未満であるか否かを判定することで、トナーの帯電性が劣化しているか否かを判定する(S125〜S145)。 - 特許庁
The electromagnetic pressure regulator valve 6 is formed in a manner so as to regulate the gas pressure of fuel gas flowing through the supply passage 4 in accordance with an electric current flowing therewithin, and the gas pressure on the downstream side of the electromagnetic pressure regulator valve 6 is detected by a low-pressure-side pressure sensor 9.例文帳に追加
電磁式調圧弁6は、供給通路4を流れる燃料ガスのガス圧をそこに流される電流に応じた圧力に調圧するようになっており、電磁式調圧弁6より下流側のガス圧が低圧側圧力センサ9によって検出されている。 - 特許庁
To provide an oxidation-reduction electric current measuring instrument and a sensor for it capable of separately measuring different constituents, free residual chlorine, bonding residual chlorine, and dichloroamine especially, in a shot time, allowing easy measurement, and minimizing the installation space, installation cost and the like.例文帳に追加
異なる成分、特に遊離残留塩素、結合残留塩素、ジクロラミン等を短時間で分別測定できると共に、測定作業が簡便であり、設置場所や設置費用等を最小限に留めることができる酸化還元電流測定装置のセンサ及び酸化還元電流測定装置を提供する。 - 特許庁
When a particulate substance captured by the filter 3, 4 is heat incinerated, a controller 20 controls current carried to a heater 32 in response to a detection temperature by the temperature sensor 18, 19, the temperature of the filter 3, 4 is suppressed to a fixed temperature or less, overheating of the filter 3, 4 is prevented.例文帳に追加
フィルタ3,4に補集されたパティキュレート物質を加熱焼却するときには,コントローラ20は,温度センサ18,19による検出温度に応答してヒータ32への通電を制御し,フィルタ3,4の温度を一定温度以下に抑制し,フィルタ3,4の過熱を防止する。 - 特許庁
In an electrically-driven pump to discharge the working fluid stored in the reservoir 2 by reciprocating the working fluid through the expansion/contraction of a solid element 7, the current of a coil 8 of a piston drive part 1b to be applied to the solid element 7 is controlled according to the measured value of the pressure sensor 21.例文帳に追加
固体素子7の伸縮動作によってピストンが往復動して前記リザーバ2に貯留された作動流体を吐出する電動式ポンプは、前記固体素子7に印加する、ピストン駆動部1bのコイル8電流が前記圧力センサ21の計測値に応じて制御される。 - 特許庁
To provide a smart grid power generation method utilizing an overcurrent such as an inductive current, electromagnetic waves and static electricity surge generated in an electric wire, a communication line, a sensor, a television, or an optical communication cable or the like by lightning strike or lightning to a photovoltaic power generation panel, outdoor/indoor illumination or an air conditioner, and its monitoring system.例文帳に追加
太陽光発電のパネル・屋外・屋内照明又はクーラーへの落雷、又は稲光によって電線・通信線・センサ・テレビ・光通信ケーブルに生じる誘導電流、電磁波、静電気サージ等の過剰電流を利用したスマートグリッド発電方法とその監視システムを提供する。 - 特許庁
A field generation part 34 in the satellite sensor circuit section 63a generates a minute electric field based on a voltage supplied from the master determination section to the power supply line VDDL to feed a modulation current according to an occupant seating state and a seat belt wearing state to the power supply line VDDL.例文帳に追加
サテライトセンサ回路部63aにおける電界発生部34は、マスター判定部から電源供給ラインVDDLへ供給される電圧により微弱電界を発生し、乗員着席状況、シートベルト装着状況に応じた変調電流を電源供給ラインVDDLへ流す。 - 特許庁
The Hall effect device 100 comprises supports 11 to 14 formed on a first semiconductor substrate 10 made of n-type single crystal silicon, a Hall device part 15, a space 16, current electrode terminals 21a to 22a, sensor electrode terminals 23a to 24a, wirings 21b to 24b, and bonding pads 21c to 24c.例文帳に追加
ホール効果素子100は、N型単結晶シリコンからなる第1の半導体基板10に形成される支持部11〜14、ホール素子部15、空間部16、電流電極端子21a〜22a、センサ電極端子23a〜24a、配線21b〜24b、ボンディングパッド21c〜24cなどを備える。 - 特許庁
Using a heater and a metal oxide semiconductor gas sensor having a gas sensitive body, when a measurement start switch is turned on at the time of To, first of all it goes into the high-temperature heating mode TH for high-temperature heating the gas sensitive body by driving the heater with on-duty current pulse PW of relatively large value with a prescribed period.例文帳に追加
ヒータと感ガス体を有する金属酸化物半導体ガスセンサを用い、時刻Toで測定スタートスイッチが投入されるとまず高温加熱モードTHに入り、感ガス体を高温加熱するために所定周期で相対的に大きな値のオンデューティの電流パルスPWでヒータを駆動する。 - 特許庁
To provide a metal terminal member in which electrode terminal parts of a detecting element hardly exfoliate and a lead wire hardly comes off even in the case that an external force is impressed on the lead wire and which is capable of maintaining the insulating property of each current path and to provide a sensor provided with the same.例文帳に追加
リード線に対して外力が印加された場合においても、検出素子の電極端子部が剥離し難く、リード線の抜け落ちが生じ難く、各電流経路の絶縁性を維持できる金属端子部材、および金属端子部材を備えるセンサを提供する。 - 特許庁
To provide a smoke sensor for simplifying or eliminating a means for preventing disturbance light from being incident on a light-receiving unit by preventing the output voltage of a current-voltage converting circuit from being saturated due to the influence of DC components which is generated when the disturbance light is made incident on the light receiving unit.例文帳に追加
受光部に外乱光が入射することで発生する直流成分の影響により電流電圧変換回路の出力電圧が飽和することを防止し、受光部への外乱光の入射を防止する手段を簡素化あるいは省略できる煙感知器を提供する。 - 特許庁
The light source unit (30) comprises a group of bicolor light emitting diodes to obtain a sufficient quantity of illumination light, and drive current of the light emitting diodes in the groups thereof with respective colors is so set as to offset the bias in the spectral sensitivity characteristic of individual colors of the image sensor.例文帳に追加
光源ユニット(30)が十分な照明光量を得るための少なくとも二色の発光ダイオード群から成り、それぞれの色の発光ダイオード群の発光ダイオードの駆動電流が撮像センサのそれぞれの色の分光感度特性の偏りを相殺するように設定される。 - 特許庁
Reference resistance bodies 31, 32, 33, and 34 are prepared and in addition to wires 3a and 3b of a temperature measuring resistance body sensor 1, those reference resistance bodies are connected to a constant-current power source 14 in order; and generated voltages are measured and compared to find the temperature.例文帳に追加
複数の基準抵抗体31、32、33および34を用意し、測温抵抗体センサ1の配線3aおよび3bに加え、これらの基準抵抗体も定電流電源14に順番に接続し、発生する電圧を測定し、さらに、これらの電圧を比較することにより温度を求める。 - 特許庁
A discharge current based on charging voltage of the condenser 120 flows at each resistant 110a, 110b, 10c and FET 130, when applied voltage of DC voltage from a battery B for a control device Ea to an ignition switch IG is momentary stopped while the pulse signal from a speed sensor S is at a high level.例文帳に追加
制御装置EaへのバッテリBからイグニッションスイッチIGを介する直流電圧の印加が、スピードセンサSからのパルス信号のハイレベル中に瞬断されたとき、コンデンサ120の充電電圧に基づく放電電流が各抵抗110a、110b、10c及びFET130に流れる。 - 特許庁
A ball clogging judgment apparatus monitors the electrified state between the prescribed two game spikes 70A and 70B based on a detection signal from the current detection sensor 62, and outputs an electrified state detection signal when the electrified state between the game spikes 70A and 70B continues for a prescribed time or longer than this.例文帳に追加
球詰まり判定装置は、電流検知センサ62からの検知信号に基づき、所定の2本の遊技釘70A,70B間の通電状態を監視し、遊技釘70A,70B間が所定時間以上継続して通電状態であるときに通電状態検出信号を出力する。 - 特許庁
An electromagnetic induction type position sensor includes the coils 6 for receiving the alternating current magnetic flux of repeating high intensity and low intensity at substantial wavelength λ along a relative moving direction of a position detecting object, and for outputting an electromagnetic induced voltage varied accompanying a relative motion of the position detecting object.例文帳に追加
電磁誘導型位置センサは、位置検出対象物の相対移動方向にほぼ波長λで強弱を繰り返す交流磁束を受信して、前記位置検出対象物の相対移動に伴って変化する電磁誘導電圧を出力するコイル6を備える。 - 特許庁
Since the sensor of the rod-shaped electromagnetic current meter is inserted from the pipe side, avoiding the pipe top where the air passes and the pipe bottom where deposited refuse passes, the pipe line flowmeter having high accuracy without being influenced by the air and the floating refuse can be provided, to thereby enable inexpensive and careful water management.例文帳に追加
エアーが通過する管頂と沈殿ごみが通過する管底を避けて棒状電磁流速計のセンサを管横から挿入するため、エアー及び浮遊ごみの影響もなく高精度な管水路流量計を提供でき、安価で細かい水管理が行える。 - 特許庁
The moving object estimates the current own position based on a moving distance calculated by the integration of outputs from an encoder and past particles, and calculates a correction amount of the own position based on the particle out of the plurality of particles for own position estimation that matches most closely to the measured value by the laser sensor and the own position estimated by the encoder.例文帳に追加
エンコーダの出力からの積分による移動量と、過去のパーティクルと、から現在の自己位置を推定し、自己位置推定における複数のパーティクルのうち、レーザセンサ測定値に最もマッチしたパーティクルと、エンコーダによる自己位置と、に基づいて、自己位置の補正量を算出する。 - 特許庁
To provide a power supply circuit capable of separating a first power supply part which supplies power to a sensor from a second power supply part which supplies power to a control circuit, and certainly suppressing fluctuation of output voltage due to temperature variation and current variation, and provide a water heater with the same.例文帳に追加
センサに給電する第1の電源部と、制御回路に給電する第2の電源部とを分離するとともに、温度変化や電流変化による出力電圧の変動を確実に抑制することのできる電源回路、およびこれを備えた給湯機を提供すること。 - 特許庁
To prevent the generation of an excessive current at the start of charging without reducing efficiency in charging, even if an error occurs in a voltage sensor for measuring an output voltage of an external power supply in a vehicle equipped with a power storage mechanism capable of being charged with the external power supply.例文帳に追加
外部電源により充電可能な蓄電機構を搭載した車両において、外部電源の出力電圧を測定する電圧センサに誤差が生じても、充電時の効率を低下させることなく、充電開始時における過大電流の発生を防止する。 - 特許庁
To solve the problems in a measuring cell structure in a conventional QCM sensor device that need of position control for a reference electrode and a counter electrode which are separately provided leads to an increase in price and size, and the imbalance of the current force line carried from the counter electrode to a working electrode causes deterioration of measurement accuracy.例文帳に追加
QCMセンサデバイスによる測定セル構成は、参照電極及び対極電極を別途に設けてその位置制御が必要になり、高価で大型化を招くと共に、対極電極から作用電極に流れる電流力線が不均衡となって測定精度の低下を招く。 - 特許庁
The control unit 7 inputs a detection output 16 of the five-axis sensor 5, determines whether or not the predetermined surface is turned down based on the output 16 and changes the level of a current to be supplied to the LCD display unit 4 step by step based on a result of the determination.例文帳に追加
制御部7は、5軸センサ5の検出の出力16を入力して、出力16に基づいて所定の面が下を向いているか否かを判断し、当該判断の結果に基づいてLCD表示部4に対する供給電流レベルを段階的に変更する。 - 特許庁
This limiting current type oxygen sensor 13 is constituted of at least an oxygen ion conductive solid electrolyte sheet 15, a pair of electrode films 16, 17 formed on a surface of the solid electrolyte sheet 15, and an oxygen diffusion limiting body 19 joined via a glass film 18 surrounding the one-side electrode film 16.例文帳に追加
酸素イオン伝導性固体電解質板15と、酸素イオン伝導性固体電解質板15の表面に形成した一対の電極膜16、17と、片側の電極膜16を囲む硝子膜18を介して接合させた酸素拡散制限体19とから少なくとも構成される。 - 特許庁
The sensor S, a diode D and a load resistance R are connected in series to an alternating current source P, and a comparator 5 for switching between ON/OFF states of an output by comparing the voltage amplified by an operational amplifier 6 with a prescribed threshold is connected to both ends of the load resistance R through the operational amplifier 6.例文帳に追加
センサSとダイオードDと負荷抵抗Rを交流電源Pに直列に接続し、負荷抵抗Rの両端にオペアンプ6を介し、このオペアンプ6で増幅された電圧を所定のしきい値と比較して出力のオン、オフを切り換えるコンパレータ5を接続する。 - 特許庁
The light source control method and the light source control device detect the fluctuations of the lantern as changes of acceleration by an acceleration sensor mounted on the lantern, and according to the acceleration changes, control a current of the light source mounted on the lantern by pulse-width modulation.例文帳に追加
前記光源制御方法および光源制御装置は、提灯に取り付けられた加速度センサにより、提灯の揺れを加速度の変化として検出し、前記加速度変化に応じて、前記提灯に取り付けられた光源の電流をパルス幅変調することにより制御する。 - 特許庁
To provide an optical system sensor device utilizing the characteristics of a current and a voltage acting on light for measuring a transmission and distribution line such as a distribution line or a transmission line for the quantity of electricity, offering cost savings by shortening the service range of an optical fiber cable.例文帳に追加
電流および電圧が光に作用する性質を利用して配電線または送電線などの送配電線の電気量を測定する光方式センサ装置に関し、光ファイバケーブルの使用距離を短縮することによってコスト的に優れた光方式センサ装置を提供するものである。 - 特許庁
The air-fuel ratio control device controls the air-fuel ratio in accordance with the electromotive force when the completion of fuel property determination is not recognized, and controls the air-fuel ratio in accordance with a sensor current detected at the application of the positive voltage when the completion of fuel property determination is recognized.例文帳に追加
空燃比制御装置は、燃料性状判定の完了が認められない場合に起電力に応じて空燃比制御を行い、燃料性状判定の完了が認められた場合に、正電圧印加時に検出されるセンサ電流に応じて空燃比制御を行う。 - 特許庁
Then, water boils if temperature in the inner pot gets to 100°C, the temperature sensed through generated vapor by a cover temperature sensor becomes 100°C a little later and the boiling state is detected, the heating element 15 is stopped to generate heat and the current applied to the electromagnetic induction coil is properly controlled.例文帳に追加
その後、内釜内の温度が100℃に達すると、水が沸騰し、発生した水蒸気によって蓋部温度センサによる検知温度もやや時間が遅れて100℃となり、沸騰状態を検知すると、発熱体15の発熱を停止し、電磁誘導コイルの通電量を適宜、制御する。 - 特許庁
The inverter controller 13 controls the revolution of the synchronous motor 12 based on an output signal equivalent to the pressure of oil from a current sensor 31 and a pressure commanding signal so as to control the pressure of a discharge line 7 based on the revolution of the fixed displacement type hydraulic pump.例文帳に追加
インバータコントローラ13は、電流センサ31からの油の圧力に相当する出力信号と圧力指令信号とに基づいて、同期モータ12の回転数を制御して、固定容量型油圧ポンプ11の回転数によって吐出ライン7の圧力を制御する。 - 特許庁
To provide a sequencer to make a contribution to enhance a capacity operating rate by incorporating a fault display and an overdrive preventing circuit for monitoring the state of the brake lining and for monitoring the states of sensor because the current machine using the brake motor as a driving source is incorporated with a sequencer controller and is a controller for forward and reverse operation.例文帳に追加
現状のブレーキモータを駆動源とする機器は大部分はシーケンサーコントローラが組み込まれていて、正逆運転だけのコントローラですので、ブレーキライニングの状態監視、センサーの状態監視に、異常表示、暴走防止回路を組込、稼働率アップに貢献するシーケンサーとなる。 - 特許庁
To provide a current-voltage converting circuit capable of heightening the upper limit of largeness of a DC component for suppressing influence on an output voltage compared with the conventional configuration, while suppressing the reduction of an SN ratio between an input terminal and an output terminal, and to provide a smoke sensor including the same.例文帳に追加
入力端子と出力端子との間のSN比の低下を抑制しつつも、従来構成に比べて出力電圧への影響を抑制可能な直流成分の大きさの上限を広げることができる電流電圧変換回路およびそれを備えた煙感知器を提供する。 - 特許庁
The user identification device has a registeration means 27 capable of registering the output signal of a piezoelectric sensor 6 varying with the rhythm of tapping on an elastic body 7 by the user and an identifying means 28 of identifying the user according to how much current output matches the output registered by the registeration means 27.例文帳に追加
使用者が弾性体7をタップするリズムに応じて変化する圧電センサ6の出力信号を登録できる登録手段27と、登録手段27に登録された出力と現在の出力の一致度合いにより使用者を識別する識別手段28とを有している。 - 特許庁
When starting the preheat mode (S1:YES), a minute constant electric current Icp is not supplied from a gas sensor controller to the detection element but only power application to a heater is started (S2) in order to raise the temperature of the detection element to a temperature less than the splashed water crack occurrence temperature.例文帳に追加
このプレヒートモードを開始させる場合(S1:YES)、ガスセンサ制御装置からガス検出素子への微小な定電流Icpの供給を行わず、飛水割れ発生温度未満の温度にガス検出素子の温度を上昇させるためのヒータ体への通電のみを開始させる(S2)。 - 特許庁
To provide an image forming apparatus by which stable image formation can be carried out by preventing output variation in image density detection due to variation in output of an image density detection sensor, dark current, delay in response of an amplifier and furthermore, dispersion of optical reflecting ratio of a photoreceptor drum.例文帳に追加
画像濃度検知センサの出力変動、暗電流、及び増幅器等による応答遅れ、更に感光体ドラムの光反射率のバラつきによる画像濃度検知出力変動を防止し、安定した画像形成を可能とする画像形成装置の提供にある。 - 特許庁
In this case, a fan control part 8 cools the electric power amplifying circuit 5 by rotating a cooling fan by supplying an electric current to a fan motor 7 when a temperature of the electric power amplifying circuit 5 detected by a temperature sensor 9 becomes a preset temperature or more (for example, a temperature unreachable in ordinary operation).例文帳に追加
この際、ファン制御部8では、温度センサ9で検出した電力増幅回路5の温度が、設定温度(例えば、通常運転では到達し得ない温度)以上となると、ファン・ファンモータ7に電流が供給され、冷却ファンが回転して電力増幅回路5を冷却する。 - 特許庁
The ground fault accident of a DC circuit 30 connected, through a rectifier 20, to a non-grounding AC circuit 10 on the secondary side of a main transformer 1, is detected through a change in a DC potential of a grounding resistor 50 for limiting a DC ground fault current which is arranged at an AC ground fault sensor 40 on the AC circuit 10 side.例文帳に追加
主変圧器1の二次側の非接地系交流回路10に整流器20を介して接続された直流回路30の地絡事故を、交流回路10側の交流地絡センサ40に配設した直流地絡電流制限用接地抵抗50の直流電位変化で検出する。 - 特許庁
Moreover, the method corrects the difference amount of the alignment detected by the first sensor based on the non-linear shape of the edge of the belt loop to generate a corrected difference value of the alignment and adjust the current lateral position of the belt loop in the apparatus relative to the known alignment position based on the corrected difference value of the alignment.例文帳に追加
また、ベルトループのエッジの非直線形状に基づき第1のセンサが検出する整列誤差量を修正し、修正整列誤差値を生成し、修正整列誤差値に基づき既知の整列位置に対する装置内のベルトループのそのときの側方位置を調整する。 - 特許庁
To provide a magnetoresistance effect sensor in which the generation of a Barkhausen noise can be suppressed by preventing a magnetic domain such as a closure domain from being formed in a free magnetization layer, by a galvano magnetic field to be guided to the intra-film surface direction by operation in a mode for electrifying a sense current vertically to a film surface.例文帳に追加
センス電流を膜面垂直方向に通電するモードで動作し、膜面内方向に誘導される電流磁界による磁化自由層での還流磁区などの磁区形成を防ぐことができ、バルクハウゼンノイズの発生を抑制できる磁気抵抗効果センサーを提供する。 - 特許庁
An output of the current sensor 4a is compared with the threshold for detecting the volume of dust and the threshold for detecting the closed state in the air path to display the volume of dust of the dust collection part and the closed sate in the air path on a display part 8 based on the results of the comparison.例文帳に追加
そして、電流センサ4aの出力とゴミ量検出用のしきい値及び風路内の密閉状態検出用のしきい値とを比較してその比較結果に基づいて集塵部のゴミ量及び風路内の密閉状態を表示部8に表示させる。 - 特許庁
This device has a bias component setting part 28 for variably setting a bias component for generating a bias magnetic field by feeding coils 33-36 of a sensor part 30A and compensates for the measured value midpoint deviation of the forward/backward torque, by setting a direct current component by the bias component setting part 28.例文帳に追加
センサ部30Aのコイル33〜36に給電してバイアス磁界を発生させるバイアス成分を可変設定するバイアス成分設定部28を有し、バイアス成分設定部28による直流成分の設定により正逆トルクの計測値中点ずれを補償する。 - 特許庁
To provide a multi-port memory device capable of preventing an initial high data discrimination error at the time of initial operation in a global data bus transmitting/receiving structure of a current sensor system at the time of transmitting low data, and also to provide a multi-port memory device capable of transmitting a data faster.例文帳に追加
ローデータの送信時、問題を誘発せずに電流センサ方式のグローバルデータバス送受信構造における初期動作時、最初のハイデータ判別エラーを防止できるマルチ−ポートメモリ素子を提供し、また、より速いデータ送信が可能なマルチ−ポートメモリ素子を提供すること。 - 特許庁
The one electrode 22 in the sensor cell 20 is a longer distant apart from the heating pattern 12 to bring high insulation resistance, compared with that when overlapped with the heating pattern 12 on the layered face, and the detection precision is hardly affected by the leak current from the heating pattern 12 as a result thereof.例文帳に追加
これにより、センサセル20における一方の電極22は、積層面において発熱パターン12と重なっている場合と比べて、発熱パターン12からの距離が遠くなることで絶縁抵抗が高くなるため、結果、発熱パターン12からの漏れ電流の影響を受けにくくすることができる。 - 特許庁
Failure of a current sensor 62, 64 is determined using the difference Dw between an input power Win to a DC/DC converter 36 and the sum of an output power Wout from the DC/DC converter 36 and an estimated loss Lcon generated in the DC/DC converter 36.例文帳に追加
DC/DCコンバータ36への入力電力Winと、DC/DCコンバータ36からの出力電力Wout及びDC/DCコンバータ36で発生する推定損失Lconの和との差Dwを用いて電流センサ62、64の故障を判定する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|