「tensile strength」に関連した英語例文の一覧と使い方(68ページ目) - Weblio英語例文検索

The nonwoven fabric for the cosmetic sheet product includes (a) a fiber having a single fiber diameter of 1-500 nm and formed from a thermoplastic resin, and (b) a fiber having a wet tensile strength of 2.0 cN/dtex or more, so that the fibers are three-dimensionally entangled, and the nonwoven fabric is impregnated with a chemical solution.例文帳に追加

単繊維直径が１〜５００ｎｍの熱可塑性樹脂からなる繊維（ａ）と少なくとも湿潤時の引張強度が２．０ｃＮ/ｄｔｅｘ以上の繊維（ｂ）とが３次元的に交絡しているシート型コスメ製品用不織布に薬液を含浸する。 - 特許庁

The polylactic acid crimped yarn has the following characteristics: made from a polylactic acid polymer 9-22 in relative viscosity, total fineness is 600-2,500 dtex, tensile strength is 1.0-3.0 cN/dtex, percent elongation after subjected to boiling water treatment is 3-15%, and coefficient of dynamic friction( yarn-metal ) is ≥0.4.例文帳に追加

本発明のポリ乳酸捲縮糸は、相対粘度が９〜２２のポリ乳酸ポリマより構成され、総繊度が６００〜２５００ｄｔｅｘ、引張り強度が１．０〜３．０ｃＮ／ｄｔｅｘ、かつ沸騰水処理後の伸長率が３〜１５％、糸−金属動摩擦係数が０．４以下であることを特徴とするものである。 - 特許庁

In the production of the cold-rolled material for spring, after applying the finish cold-rolling, the cold-rolled material for spring excellent in the spring limiting value, is produced by applying a stretch-leveller work, where unit tension is set to be ≥60% of 0.2% proof stress value and ≤95% tensile strength.例文帳に追加

ばね用冷間圧延材の製造において，仕上げ冷間圧延を施したのち，ユニットテンションを0.2%耐力値の60%以上，引張強さの95%以下に設定したストレッチャレベラ加工をほどこすばね限界値に優れたばね用冷間圧延材の製造方法。 - 特許庁

To provide an acrylic rubber composition giving a vulcanized product having highly balanced heat-resistance, especially the residual ratio of tensile strength and the residual ratio of elongation after thermal aging without deteriorating physical properties in a normal state, its vulcanized product, and a hose, a sealing part and a vibration-proof rubber article produced by using the composition.例文帳に追加

加硫物とした際に、常態物性を損なわず、耐熱性、特に熱老化後の引張強さの残留率と伸びの残留率のバランスに優れるアクリルゴム組成物とその加硫物、およびこれを用いたホース部品、シール部品、防振ゴム部品を提供する。 - 特許庁

The optical filter has at least a sheet of a transparent film with ≥10 MPa tensile strength, ≥150% elongation after fracture, ≤6% haze and further with 0.3-3 mm thickness as a transparent supporting body, and the picture display device utilizes the optical filter.例文帳に追加

引張り強度が１０ＭＰａ以上、破断伸度が１５０％以上、ヘイズが６％以下、かつ厚みが０．３ｍｍ〜３ｍｍの透明フィルムを透明支持体として少なくとも１枚有する光学フィルターおよびこの光学フィルターを用いた画像表示装置。 - 特許庁

It thereby becomes a thick, high tensile-strength hot-rolled steel sheet having a structure in which the minimum lath intervals in bainite or tempered martensite in the surface of the steel sheet is ≥0.1 μm, and structural variation in the sheet thickness direction is reduced, and having low temperature toughness and particularly excellent DWTT characteristics and CTOD characteristics.例文帳に追加

これにより、鋼板表面のベイナイトまたは焼戻マルテンサイトの最小ラス間隔が0.1μm以上と、板厚方向の組織変動が少ない組織となり、低温靭性、とくにＤＷＴＴ特性とＣＴＯＤ特性に優れた厚肉高張力熱延鋼板となる。 - 特許庁

In the method for producing the NiTi based alloy wire, an NiTi based alloy wire rod subjected to cold wire drawing, in which the thickness of an oxidized film is ≤3 μm is subjected to heat treatment of applying tension by 20 to 70% of its tensile strength at 300 to 450°C for 5 sec to 1 min.例文帳に追加

酸化膜の厚さが３μｍ以下の冷間伸線上がりのＮｉＴｉ系合金線材に、その引張強さの２０〜７０％の張力を３００〜４５０℃の温度で５秒以上１分以下負荷する熱処理を施すＮｉＴｉ系合金ワイヤの製造方法。 - 特許庁

The light diffusion film manufactured by this method has entire light beam transmittance of 85% or higher, haze of 50% or higher, 3% or lower of a size change ratio at 150°C in the vertical and horizontal directions and tensile strength of 100 MPa or higher in the vertical and the horizontal directions.例文帳に追加

前記方法で製造された、全光線透過率が８５％以上、ヘーズが５０％以上、１５０℃における寸法変化率が縦方向及び横方向とも３％以下、引張強さが縦方向及び横方向とも１００ＭＰａ以上であることを特徴とする光拡散性フィルム。 - 特許庁

Even at low draw ratios, the composition is assured to have a high processability, minimizes the imbalance of physical properties between in the machine direction and in the lateral direction of its stretched film, improves the tensile strength of the film, and prevents advantageously the reduction of physical properties caused by the inorganic filler.例文帳に追加

前記組成物は、低い延伸率においてでも、高い加工性が保証され、延伸フィルムの機械方向と横軸方向との間の物理的性質の不均衡を最少化し、フィルムの引張強度が向上し、無機充填材による物理的性質の低下を防ぐという利点を有する。 - 特許庁

The material, as compared with a conventional conductive and reinforcing material, can provide improved characteristics such as conductivity, rigidity, tensile strength, increased abrasion resistance for static prevention and electromagnet shielding materials with high cost-effectiveness.例文帳に追加

材料は、従来の導電性および強化材料に比べて、導電率、並びに、剛性、引張り強さおよび引っ掻き抵抗の増加のような改善された物理的性質を、熱可塑性および熱硬化性ポリマーのような帯電防止および電磁シールド用材料に費用効率の高い方法で提供する。 - 特許庁

To obtain a thick steel plate for a welded structure which has excellent fatigue crack propagation resistance of a base material without depending on the addition of a large quantity of special or expensive alloy elements, or depending on a production method which is inferior in productivity or is complicated, or without the placement of large restrictions on tensile strength and steel plate thickness.例文帳に追加

母材の耐疲労き裂伝播特性が優れた溶接構造物用厚鋼板を、特殊なあるいは高価な合金元素の多量添加や、生産性の劣る、あるいは複雑な製造方法によらずに、また、引張強度や鋼板板厚に大きな制限を受けずに得る。 - 特許庁

A gripping block (1), a grip fixture (2) held in the gripping block (1), the cutter (3) held in the gripping block (1) so as to be movable vertically, and a tensile tester 9 connected to the grip fixture (2), are provided to the bonding strength testing machine for the bonding wire.例文帳に追加

把持ブロック(1)と、把持ブロック(1)内に保持されたグリップ冶具(2)と、垂直方向に移動可能に把持ブロック(1)内に保持されたカッタ(3)と、グリップ冶具(2)に連結された引張試験機(9)とをボンディングワイヤの接合強度試験装置に設ける。 - 特許庁

Alternatively, the α+β type titanium alloy for casting further comprises C+N+O by ≤1.0 mass% and/or B+Si by ≤0.5 mass%, and the balance Ti with inevitable impurities, and in which tensile strength is ≥890 MPa, and whose melting point is ≤1,650°C.例文帳に追加

更に、Ｃ＋Ｎ＋Ｏ：１．０ｍａｓｓ％以下、および／または、Ｂ＋Ｓｉ：０．５ｍａｓｓ％以下を含み、残部がＴｉ及び不可避的不純物からなり、鋳造まま状態で引張強さが８９０ＭＰａ以上であり、融点が摂氏１６５０度以下である鋳造用アルファ＋ベータ型チタン合金。 - 特許庁

To provide a resin composition for optical three-dimensional molding which can be formed into a three-dimensional molded article excellent in tensile strength, elongation, and heat resistance after curing even with an optical three-dimensional molding apparatus using pulse oscillation light as optical energy for curing.例文帳に追加

硬化用の光エネルギーとしてパルス発振光を用いる光学的立体造形装置を用いる場合においても、硬化後の引張強伸度特性に優れ、その耐熱性が良好な立体造形物を形成できる光学的立体造形用樹脂組成物を得る。 - 特許庁

To provide a rubber composition for tires easily obtainable of excellent reinforcing properties and improving low fuel consumption and tensile strength even if calcium carbonate is used as a filler, and to provide a pneumatic tire using the rubber composition for tires for each member of the tire.例文帳に追加

炭酸カルシウムを充填剤として使用した場合であっても、簡便に優れた補強性が得られ、低燃費性、引張強度を向上できるタイヤ用ゴム組成物、及び該タイヤ用ゴム組成物をタイヤの各部材に用いた空気入りタイヤを提供する。 - 特許庁

To provide a reinforcing fitting assembly for a steel-pipe steel tower, which can be simply mounted on a gusset-plate welding node steel pipe of an existing steel-pipe steel tower only by bolt-nut fastening, and which can impart desired tensile strength to the node steel pipe.例文帳に追加

既設鋼管鉄塔のガセットプレート溶接節点鋼管にボルト−ナット締めのみで簡便に装着でき、しかも節点鋼管に所望の引張強度を与えることができる鋼管鉄塔用補強金具組立体を提供すること。 - 特許庁

The aluminum alloy is composed of 0.90-1.60 mass % Fe, 0.03-0.20 mass % Si, 0.0005-0.030 mass % Cu and the balance Al with unavoidable impurities, wherein the tensile strength is 170-120 MPa without process annealing in cold rolling.例文帳に追加

アルミニウム合金は、Ｆｅ：０．９０乃至１.６０質量％、Ｓｉ：０.０３乃至０.２０質量％及びＣｕ：０.０００５乃至０.０３０質量％を含有し、残部がＡｌ及び不可避的不純物からなる組成を有し、冷間圧延時に中間焼鈍を行わず、引張強度が１７０乃至２１０ＭＰａである。 - 特許庁

To provide a conductive composition for electrophotographic equipment, capable of achieving both of superior sagging resistance and low hardness after crosslinked as well as achieving both of reduction in contaminating property and improvement in a crosslinking speed by suppressing generation of a crosslinking residual component, and further reducing a volume resistivity and showing excellent tensile strength after crosslinked.例文帳に追加

架橋後に優れた耐ヘタリ性と低硬度を両立できるとともに、架橋残渣成分の発生を抑えることによる汚染性の低減と架橋速度の向上を両立でき、さらには、体積抵抗率を低くでき、架橋後の引張強度に優れた電子写真機器用導電性組成物を提供すること。 - 特許庁

As the copper foil, e.g., electrolytic copper foil in which tensile strength after heating at 180°C for 1 hr is ≥50 kgf/mm^2, elongation percentage after heating at 180°C for 1 hr is ≥3.0%, and surface roughness (Rz) in the rough surface is ≤2 μm is adopted.例文帳に追加

上記目的を達成した銅箔は、１８０℃×１時間加熱後の引張り強さが５０ｋｇｆ／ｍｍ^２以上、１８０℃×１時間加熱後の伸び率３．０％以上、粗面の表面粗さ（Ｒｚ）が２μｍ以下、であることを特徴とする電解銅箔等を採用する。 - 特許庁

Paper substrates, which are 0.5-0.8 in bulk density, 9.8 N or more per width of 10 mm in tensile strength, and 100 μm or less in thickness, are impregnated with a varnish composed mainly of an epoxy resin and then dried by heating for the fabrication of prepregs to be built into laminates for printed wiring boards.例文帳に追加

嵩密度が０．５〜０．８、引張り張力が９．８Ｎ／１０ｍｍ巾以上で厚みが１００μｍ以下である紙基材に、エポキシ樹脂を主成分としたワニスを含浸し加熱乾燥してなる印刷配線板用プリプレグを用いて積層板とする。 - 特許庁

This separator for a battery is characteristically composed by using a non-woven fabric wherein, when it is assumed that a machine direction is a direction MD and a direction perpendicular to the direction MD is a direction CD, the ratio of tensile strength in the direction MD to that in the direction CD is 0.7-3.0.例文帳に追加

機械方向をＭＤ方向とし、ＭＤ方向に直交する方向をＣＤ方向としたとき、ＣＤ方向に対するＭＤ方向の引張強度比が、０．７〜３．０である不織布を用いてなることを特徴とする電池用セパレータ。 - 特許庁

The optical fiber unit (10) provided with a tensile strength body (12) located at the center, a plurality of optical fibers (14) arranged around the body (12) in a twisted state and fixed by a filler (18) and a coat (16) arranged on the outer periphery is used for an optical submarine cable.例文帳に追加

中心に位置する抗張力体（１２）と、抗張力体の周りに撚り状態で配置され、充填材（１８）で固定される複数の光ファイバ（１４）と、外周に配置される被覆（１６）とを備え、光海底ケーブルに使用される光ファイバユニットである。 - 特許庁

To obtain a steel sheet which has a specific tensile strength and excellent toughness and is optimum for a large structure by composing it of a specified compsn., allowing it to have residual austenite in a specified volume ratio and allowing MSO value to satisfy a specified temp. range.例文帳に追加

４４０〜６４０ＭＰａ程度の引張強さを有し且つ優れた靱性をも発揮し、海洋構造物、船舶、貯蔵タンク等の大型構造物に使用される素材として最適な変態誘起塑性鋼板、および製造方法を提供する。 - 特許庁

Although a tensile strength of the fabric 16 acts on an acute-angle part 21 formed in a corner part on the outer edge side of the cushioning part 15 at this time, the deformation due to the collapse of the acute-angle part 21 of the cushioning part 15 can be suppressed by forming a chamfered part 22 in the acute-angle part 21.例文帳に追加

このとき、クッション部15の外縁側角部に形成される鋭角部21には布地16の抗張力が作用するが、鋭角部21に面取り部22を形成することで、クッション部15の鋭角部21の潰れによる変形を抑制することができる。 - 特許庁

The rubber composition contains a carbon black having the characteristics (A)-(C) mentioned below and a rubber as the essential components, and it has, after vulcanized, a tensile strength (TB) of ≥9.8 MPa, a volume resistivity of ≥1×10^5 Ωcm, and an AC resistance (impedance) of ≥1×10^4 Ωcm.例文帳に追加

下記の特性（Ａ）〜（Ｃ）を備えたカーボンブラックと、ゴムとを必須成分とするゴム組成物であって、加硫後の引張り強さ（ＴＢ）が９．８ＭＰａ以上で、体積抵抗率が１×１０^5 Ω・ｃｍ以上で、交流抵抗（インピーダンス）が１×１０^4 Ω・ｃｍ以上である。 - 特許庁

In an actual state, in a fracture test, as being contrary to a conventional technology, there is no case of the fracture at a boundary, all are fractured at a base material or a heat affected zone, the tensile strength is extremely high, sound joining of no defect made of the matrix toughened higher than the base material is obtained.例文帳に追加

実施形態では、従来技術とは対称的に破壊テストにおいて界面における破断が一例もなく、すべて母材（ＦＣＤ）または熱影響部より破断しており、引張り強度もきわめて高く、健全で母材よりもむしろ強靱化された基地よりなる無欠陥の接合を立証している。 - 特許庁

To provide a curable composition and a sealing material composition each of which can easily be produced, has good storage stability, is moisture- cured to give a rubber-like elastic material having a high tensile strength and a low modulus with a high elongation, and is excellent in adhesiveness, weatherability, heat resistance, and durability e.g. water resistance in particular.例文帳に追加

製造し易く、保存安定性の良い、湿気硬化して高い引張り強度と低モジュラスで大きな伸びを有するゴム状弾性体となる、接着性、耐候性、耐熱性、特に耐水性などの耐久性に優れた硬化性組成物及びシーリング材組成物を提供する。 - 特許庁

To provide a new aqueous dispersion of a polyamide-based rubber elastomer capable of being used for produce a molded article that is excellent in heat resistance and durability, can maintain excellently mechanical characteristics such as tensile strength and elongation etc.even after heating for a long period of time, and is so excellent in discoloration resistance as to hardly discolorate even after a long lapse of time.例文帳に追加

耐熱性及び耐久性に優れ、長時間加熱後も引張強度、伸び等の機械的特性が良好に維持され、長期間経過後もほとんど変色しない耐変色性に優れた成形品を製造することが可能な新規なポリアミド系ゴム弾性体の水性分散液を提供する。 - 特許庁

A laminated band element with a maximum width of 5 mm comprises at least one flexible graphite film 1 with a maximum thickness of 1 mm and a bulk density from 0.7 to 1.8 g/cm3, and at least one metal film 3 with a thickness from 5 to 50 μm and a minimum tensile strength of 250 MPa.例文帳に追加

積層材の帯材は最大で５ｍｍの幅を持ち、可撓性グラファイト１の少なくとも１枚の層と、少なくとも２５０ＭＰａの引っ張り強度を持つ金属フィルム３の少なくとも１枚の層とから構成されている。 - 特許庁

When tensile strength of a compensation rope 8 stretched to a lower surface of a counterweight from a lower surface side of a car 5 through a compensation sheave arranged on a pit part of a hoistway floor side is large, the natural frequency of the compensation rope 8 is large.例文帳に追加

乗りかご５の下面側から昇降路床部側のピット部に配設されるコンペンシーブを経由して釣合いおもり下面に掛け渡されたコンペンロープ８の張力が大きくなればコンペンロープ８の固有振動数は大きくなる。 - 特許庁

To obtain a thermoplastic resin composition which has low stiffness in tensile strength, and the like, and an excellent chemical resistance, is so ductile that there is no sharp edge on a fracture surface of a molded item, shows a high thermo-deformation resistance, has a good surface even after being coated and is suitable for a part of an automobile.例文帳に追加

引張強度等の剛性が低く、耐薬品性に優れ、成形品の破断面がシャープエッジとならず延性的で、耐熱変形性が高く、成形加工性に優れ、塗装を施した後でも良好な表面性を有し、自動車部品に適した熱可塑性樹脂組成物を提供する。 - 特許庁

The polyester microfiber has a single fiber diameter of 10-1000 nm, a variation (CV%) of the single fiber diameter of 0-25%, a tensile strength of 4.0 cN/dtex or more and a fracture elongation of 10-80% as a bundle of the microfibers, and a dry heat shrinkage rate of 5% or less at 150°C.例文帳に追加

単糸繊維径が１０〜１０００ｎｍで、単糸繊維径のばらつき（ＣＶ％）が０〜２５％、極細繊維束として引張強度が４．０ｃＮ／ｄｔｅｘ以上、破断伸度が１０〜８０％、１５０℃での乾熱収縮率が５％以下であるポリエステル極細繊維。 - 特許庁

To provide a high toughness steel plate for line pipes which can be suitably used as a high toughness steel plate for line pipes being excellent in base material toughness, material uniformity of base material and HAZ (weld heat-affected zone) toughness and having ≥565 MPa tensile strength and also to provide its manufacturing method.例文帳に追加

母材靭性、母材の材質均一性およびＨＡＺ靭性に優れた引張強度５６５ＭＰａ以上の高靭性ラインパイプ用鋼板に好適な高靭性ラインパイプ用鋼板およびその製造方法を提供する。 - 特許庁

For a wiring circuit formed in an outer layer or an inner layer of the multilayer ceramic substrate, there is used metal foil containing a glass particle or a ceramic particle of 1.0 to 55.0vol% of which the tensile strength is 0.5×10^8 to 8.0×10^8Pa and a mean diameter (D50) is 10μm or less.例文帳に追加

多層セラミック基板の外層または内層に形成される配線回路層に、抗張力が０．５×１０^８〜８．０×１０^８Ｐａであって、平均径（Ｄ５０）が１０μｍ以下のガラス粒子またはセラミック粒子が１．０〜５５．０ｖｏｌ％含有されている金属箔を使用する。 - 特許庁

An alloy wire rod of a Cu-Ag alloy, a Cu-Nb alloy, a Cu-Fe alloy or a Cu-Cr alloy is wire-drawn to a final wire diameter ϕ of ≤0.1 mm, and, after that, heat treatment is performed to control its tensile strength to ≥450 MPa, elongation to ≥4%, and electric conductivity to ≥50% IACS.例文帳に追加

Ｃｕ−Ａｇ合金，Ｃｕ−Ｎｂ合金，Ｃｕ−Ｆｅ合金，Ｃｕ−Ｃｒ合金の合金線材を線径φ０．１ｍｍ以下の最終線径まで伸線した後、熱処理を施して引張強さ４５０ＭＰａ以上、伸び４％以上、導電率５０％ＩＡＣＳ以上にする。 - 特許庁

A number of natural stones which are different in size and shape are collected, and they are fastened in multiple directions by means of chain fittings 2 which are astride arbitrary ones of the natural stones 1 in directions that exerts tensile strength between the natural stones, and wedge- shaped fittings 3 each having an anchor portion 3a to be anchored at the natural stone 1.例文帳に追加

大小多種形状の自然石１を多数集合させ、任意の自然石１どうしを複数の自然石間の、引っ張り力が働く方向に跨がるチェーン金具２と、自然石１に定着されるアンカー部３ａを有するくさび形金具３とで多方向に締結する。 - 特許庁

In the permeable pavement obtained by mixing aggregate and an epoxy resin, the percentage of voids is set in 5-20 vol.%, an epoxy resin adhesive is formed in a two-pack cold quick curing type, viscosity at 20°C is set in 800-1100 mPa/sec, and tensile strength is set in 320 kg/cm2 or more.例文帳に追加

骨材とエポキシ樹脂とを混合することにより得られる透水性舗装であって、空隙率が５〜２０容量％であり、上記エポキシ樹脂接着剤が２液性の常温速硬化型であり、且つその２０℃における粘度が８００〜１１００ｍＰａ／ｓｅｃ、引張強度が３２０ｋｇ／ｃｍ^2 以上である。 - 特許庁

To provide a laminating cloth for an air duct without a pinhole, superior in heat sealability, flexibility, and flame resistance, having moderate slipping property, and wherein a woven fabric and a laminated layer have a high peel strength and a tensile elongation after fracture is maintained at 20% or less.例文帳に追加

織布とラミネート層が高い剥離強力を有しているとともに引張破断伸びが２０％以下に保たれ、かつ、ヒートシール性、柔軟性、耐摩耗性、難燃性にすぐれ、適度のスリップ性を備えたピンホールのない風管用ラミネートクロスを提供する。 - 特許庁

By this method, the aluminum alloy sheet for secondary battery case which has 260 to 350 MPa tensile strength and ≥39% IACS electrical conductivity and in which intermetallic compound particles of 0.5 to 10 μm circle-equivalent diameter are dispersed at a rate of 11,000 to 30,000 pieces/mm^2 on average can be obtained.例文帳に追加

引張強度２６０〜３５０ＭＰａ、導電率ＩＡＣＳ３９％以上、円相当直径０．５μｍ〜１０μｍの金属間化合物粒子が平均で１１０００〜３００００個／ｍｍ^２分散した二次電池ケース用アルミニウム合金板が得られる。 - 特許庁

The plastic optical cable 11 is provided with an element wire 12 and a first covering material 13 for tight covering the element wire; a second covering material 18 on a circumference of the first covering material; and a tensile-strength fiber 17 arranged between the first covering material 13 and the second covering material 18.例文帳に追加

プラスチック光ケーブル１１は、素線１２とこの素線を密着被覆する第１被覆材１３と、第１被覆材の外周の第２被覆材１８と、第１被覆材１３と第２被覆材１８との間に配される抗張力繊維１７とを備える。 - 特許庁

A polylactic acid packing band is formed of a crystalline polylactic acid resin having a D-lactic acid component in 5% or below and being 80,000 to 150,000 in a number average molecular weight, while having an embossment at least at its one side and being 5.0 kg/mm2 or more in a tensile strength.例文帳に追加

Ｄ−乳酸成分が５モル％以下、かつ、数平均分子量が８万〜１２万である結晶性ポリ乳酸樹脂からなり、少なくとも片面にエンボスを有し、引張強度が５．０ｋｇ／ｍｍ^2以上であることを特徴とするポリ乳酸製梱包用バンド。 - 特許庁

The footwear for the felling work is so formed that an upper 10 is formed by stacking a plurality of knitting which comprises an instep material 11 forming the surface of the upper 10 and synthetic fibers having a tensile strength of 20 cN/dtex or more, and is provided with a laminated member 12 provided along the inner surface of the instep material 11.例文帳に追加

本発明の伐採作業用履物は、アッパー１０が、該アッパー１０の表面を形成する甲材１１と、引張強度が２０ｃＮ／ｄｔｅｘ以上を有する合成繊維からなる編み物を複数枚重ね合わせてなり、前記甲材１１の内面に沿って設けられる積層部材１２とを具備して構成される。 - 特許庁

To provide a compression connection method of a compression sleeve with a cable having a tube body used as a stopper as well which is used for a straight line connection of an overhead transmission cable, wherein a friction force is increased and a tensile strength per a unit compression length is enhanced and workability is excellent.例文帳に追加

架空送配電線の直線接続に使用されるストッパー兼用のチューブ体を有する圧縮スリーブと電線との圧縮接続工法において、摩擦力を増大させるとともに、圧縮長さ当たりの引張り力に対する抗張力を高め、施工性のよい圧縮接続工法を提供する。 - 特許庁

To provide a dip forming composition which is suitably used as the raw material for a dip formed article having a very few pinholes, excellent hand and feel, tensile strength, and repeated fatigue characteristics, and a dip formed article, and also to provide a method for efficiently manufacturing the dip formed article.例文帳に追加

ピンホールが極めて少なく、風合い、引張り強度および繰り返し疲労特性に優れるディップ成形品の原料として好適なディップ成形用組成物、ディップ成形品および該成形品を効率よく製造するための製造方法を提供する。 - 特許庁

The hoop reinforcing layer 4 is constituted by spirally winding a ribbon-shaped material having the biaxial strength in an overlapping manner, and the tensile stress to the rate of elongation corresponding to the elongation reaching an inner surface of the tire is in a range of 70-90% of the internal pressure after the airbag is expanded.例文帳に追加

フープ補強層４は、二軸方向強力を有するリボン状材料をオーバーラップさせながら、つるまきらせん巻回して構成してなり、タイヤ内面に到達するまでの伸びに相当する伸張率に対する引張応力が、空気のうの拡張後の内圧の７０〜９０％の範囲にある。 - 特許庁