trip-wireとは 意味・読み方・使い方

To reduce abrasion by improving sliding characteristics between a contact trip and a contact wire at low costs.例文帳に追加

集電装置のすり板とトロリ線との間のしゅう動特性を低コストで改善して摩耗の低減を図ることができるしゅう動特性改善装置及びしゅう動特性改善方法を提供する。 - 特許庁

After the male housing 30 is taken out of the fitting recess 11, while locking with the lance 36 is tripped, when an electric wire W is stretched, the hook part 40 is guided along the guide surface 42, bent outward to trip the locking state, and the male side terminal metal fixture 20 can be taken out.例文帳に追加

嵌合凹部１１から雄ハウジング３０を外した後、ランス３６による係止を解除しつつ電線Ｗを引っ張ると、フック部４０は誘導面４２に案内されつつ外方へ撓まされて係止状態が解除され、雄側端子金具２０を取り出すことができる。 - 特許庁

The integrated circuit IC charges a capacitor C2, and when it is charged to a default value, this circuit outputs a trigger signal so as to turn on a thyristor SCR; and a trip coil TC excitates and drive and makes the opening and closing contact 4 opened, and a three-phase four-wire system electrical path is cut off.例文帳に追加

集積回路ＩＣはコンデンサＣ２を充電し、既定値まで充電されるとトリガ信号を出力してサイリスタＳＣＲをオンし、トリップコイルＴＣが励磁駆動して開閉接点４を開離させ、３相４線式電路が遮断する。 - 特許庁

A recovery lever 42 which can be displaced between an ordinary position and a recovery position for engaging with a trip lever 72 by rotating a pawl 29 is mounted on a base 23, and the recovery lever 42 is arranged so as to be displaced remotely from the elevator hall through a resetting wire 41.例文帳に追加

通常位置と、爪２９を回動させてトリップレバー７２に係合させる復帰位置との間で変位可能な復帰用レバー４２を基台２３に設け、この復帰用レバー４２を復帰用ワイヤ４１を介して乗場側から遠隔操作し変位させるようにした。 - 特許庁

A circuit breaker is constituted of a case 1 and a cover to constitute an equipment body, a slider 3, an electric power source side terminal part 4, a load side terminal part 5 with an abnormal electric current detection and trip function, a movable contact part 6, a switching mechanism 7 and a braided wire 8, and a spring 10 is further provided.例文帳に追加

器体を構成するケース１およびカバーと、スライダ３と、電源側端子部４と、異常電流検出・トリップ機能付きの負荷側端子部５と、可動接触子部６と、開閉機構７と、編組線８とで回路遮断器を構成し、ばね１０をさらに設ける。 - 特許庁

The resistance value of the third resistor R3 is selected so that the voltage divider voltage with a total sum of the third resistor R3 and the first resistor R1 under a condition where the lead wire 6 for phase interruption detection connected with one end of the first resistor R1 is not connected with a neutral wire N and by the second resistor R2 may exceed a trip voltage determined as failure.例文帳に追加

この第３の抵抗Ｒ３の抵抗値は、第１の抵抗Ｒ１の一端に接続された欠相検出用リード線６が中性線Ｎに接続していない状態で第３の抵抗Ｒ３と第１の抵抗Ｒ１の和と、第２の抵抗Ｒ２との分圧電圧が異常電圧検出回路２が異常と判定するトリップ電圧を超えるように選定する。 - 特許庁