startedを含む例文一覧と使い方
該当件数 : 27570件
This device performs convergence judgment of the integration term SUM, and establishes change speed of the integration term SUM to a large value before first inversion timing of output value Voxs of the oxygen concentration sensor when downstream side feedback control is started under a non-convergence condition.例文帳に追加
この装置は、積分項SUMの収束判定を行うとともに、未収束状態で下流側フィードバック制御が開始された場合、酸素濃度センサの出力値Voxsの1回目の反転時期よりも前において積分項SUMの変化速度を大きい値に設定する。 - 特許庁
When the user instructs a power stop, a switching source circuit 3 is stopped, and the power is supplied to required places by a battery 21, and the switching source circuit 3 is started at every fixed time or hour, and the battery 21 is charged, and battery exchange work is eliminated.例文帳に追加
ユーザが電源停止を指示する場合はスイッチング電源回路3を停止し電池21で必要箇所に電力を供給すると共に、一定時間あるいは時刻毎にスイッチング電源3を起動して電池21に充電して電池交換作業を不要化する。 - 特許庁
If the power supply is started, a CPU 3 turns off a switch 8 to stop the power supply to a peripheral circuit 7, and diagnoses whether the first step-down circuit 1 fails or not on the basis of a voltage V1 detected in a voltage detection circuit 4.例文帳に追加
電源装置が起動されると、CPU3は、スイッチ8をオフして周辺回路7への電力供給を停止するとともに、電圧検出回路4で検出された電圧V1に基づいて、第1降圧回路1が故障しているか否かを診断する。 - 特許庁
To prevent charging from being started as long as a midnight power contract supposing charging at home has been made, even when a charging cable integrated with an oil supply pipe is connected unless an emergency charging operation is performed, when the connection of the oil supply pipe is detected at a service station.例文帳に追加
サービススタンドで給油パイプの接続を検出した時は、緊急充電操作をしない限り、給油パイプと一体型等の充電ケーブルが接続されても、家庭での充電を前提とする深夜電力契約をしていれば充電をスタートさせない。 - 特許庁
In this hybrid automobile, when the exhaust gas purifying catalyst is judged to be in a proper state at step S112, the motoring is continued to reduce an intake air volume into cylinders until intake pipe pressure P reaches a predetermined negative pressure Pref and then combustion control is started.例文帳に追加
このハイブリッド自動車では、ステップS112で排気浄化触媒が適正状態と判定されたときには、吸気管圧力Pが所定負圧Prefとなるまでモータリングして気筒内への吸入空気量を低減させた後に燃焼制御を開始する。 - 特許庁
When an interrupt speech with another mobile radio terminal device PS3 is started thereafter, the exchange EX1 then sends music or the like based on the uploaded hold tone data to the communication partner (mobile radio terminal device PS2) being held.例文帳に追加
そして、その後、他の移動無線端末装置PS3と割込通話を開始すると、交換機EX1が保留している通信相手(移動無線端末装置PS2)に対して、アップロードした保留音データに基づく楽曲などを送出するようにしたものである。 - 特許庁
If an instruction code executed by a microprocessor matches a branch instruction of the set kind after the program execution is started by the microprocessor, a branch instruction trace data generation signal 205 is not output to a trace data generation circuit 30 and trace data 202 is not generated.例文帳に追加
マイクロプロセッサによるプログラムの実行開始後、マイクロプロセッサの実行する命令コードが、設定した種類の分岐命令と一致した場合、トレースデータ生成回路30には分岐命令トレースデータ生成信号205が出力されず、トレースデータ202が生成されない。 - 特許庁
The resin is injected into the cavity 14 under the first pressure, after gelation of the resin injected into the cavity 14 started to be gelled, the resin is injected by enhancing the injecting pressure of the resin at the second pressure higher than an injecting pressure in the case of the LRTM method.例文帳に追加
キャビティ14内に樹脂を第1の圧力で注入し、キャビティ14内に注入された樹脂がゲル化を開始した後、樹脂の注入圧力をLRTM法における注入圧力より高い第2の圧力に加圧して注入する。 - 特許庁
Out of the above, the sequential start module is electrically connected to the first fan module and the second fan module, and after a predetermined period of time passes after starting the first fan module by the input voltage, the second fan module is started by the input voltage.例文帳に追加
このうち、順次起動モジュールは、第一ファンモジュール及び第二ファンモジュールに電気的に接続され、入力電圧によって第一ファンモジュールを起動させてから所定の時間が経過した後に、入力電圧によって第二ファンモジュールを起動させる。 - 特許庁
To provide a cutter structure of a shield machine capable of cutting a tunnel wall from the center part outward to a radial direction and preventing a non-cutting part from being taken in a cutter chamber as a lump when the shield machine is started by digging the tunnel wall from the inside of an existing tunnel.例文帳に追加
既設トンネルの内部からそのトンネル壁を掘り抜いて発進する際、トンネル壁をカッタの中心部から径方向外方に切削でき、非切削部が塊としてカッタ室に取り込まれることを防止できるシールド掘進機のカッタ構造を提供する。 - 特許庁
When film formation is started, the section 100 estimates the temperatures of the wafers W in the chamber 2 by using the outputs of the temperature sensors S and the model, and separately controls the electric power supplied to the heaters 31-35 so that the estimated temperatures may be constringed to the target temperature locus.例文帳に追加
成膜処理を開始すると、温度センサSの出力とモデルとを使用して、反応管2内のウエハWの温度を推定し、推定した温度が目標温度軌道に収斂するように、ヒータ31〜35に供給する電力を個別に制御する。 - 特許庁
A CODEC circuit 106 and a record controlling unit 111 are initialized, and a clamping circuit 103 and an AGC circuit 104 are started at once after a power is applied to the recording/reproducing device, whereby an input of data into an A/D conversion circuit 105 can be kept stable.例文帳に追加
装置の電源投入後、コーデック回路106や記録制御部111の初期化を行うとともに、クランプ回路103およびAGC回路104を即座に起動することにより、A/D変換回路105の入力を安定させることができる。 - 特許庁
The sheet can be fed while the adhesion force between the sheet is reduced by controlling the pick up roller 111 to conduct a contact/separation action before the feed sheet separation means 110 is started and while a blower fan for handling the form sheet is working.例文帳に追加
分離給紙手段110の動作が開始される前で、かつ用紙サバキのためのブロワーファン動作中にピックアップコロ111が接離動作を行うように制御することにより、用紙間密着力を低減させた状態で用紙を給紙することができる。 - 特許庁
When a reset operation part 4 is operated in mounting an antibacterial keyboard cover 10 covering a keyboard 3, time measurement is started by the timer part 5, and the number of times counted by a count part 6 which counts the number of times when each key of the keyboard 3 is operated is reset.例文帳に追加
キーボード3を覆う抗菌性のキーボードカバー10を装着する際にリセット操作部4が操作されると、タイマー部5により計時を開始するとともに、キーボード3の各キーが操作される回数をカウントするカウント部6がカウントした回数をリセットする。 - 特許庁
In the control circuit 23, a voltage higher than a startable input voltage is applied before starting the high-voltage discharge lamp 21, and the high-voltage discharge lamp 21 is started with rated lamp power when the input voltage is lowered to the startable input voltage.例文帳に追加
さらに、この制御回路23では高圧放電灯21が始動する前に始動可能入力電圧よりも高い電圧が印加され、この入力電圧が始動可能入力電圧に低下した場合には、高圧放電灯21を定格ランプ電力で始動させる。 - 特許庁
In the case that the image processing is started in the processing mode set initially and the image processor decides that the processing mode is proper to the attributes of the image data, since the image processing in the processing mode can be continued, the preliminary scanning before the image processing or the like is not required.例文帳に追加
前記初期設定した処理モードで画像処理を開始させたのち、処理モードが画像データの属性に適していることが判定された場合には、その処理モードでの画像処理を継続させるから、画像処理の前の予備スキャンなどは不要である。 - 特許庁
Further the receiving device 13 brings the engine in the startable condition under the condition of the agreement of the ID codes in receiving the locking signal when the engine is not started even after the passage of the former engine startable time.例文帳に追加
また、受信装置13は、前回エンジン始動可能時間の経過後にもかかわらずエンジンが始動されなかった場合に施錠信号を受信すると、IDコード同士が一致したことを条件としてエンジンを始動可能な状態にするようになっている。 - 特許庁
When the tip of the inserting part 14 reaches the targeted part, water is supplied into the third balloon 58 from a medium supplying part 58, and the ultrasonic diagnosis is started by tightly attaching the third balloon 58 to the intestinal canal 90 and operating the ultrasonic oscillator 54.例文帳に追加
そして、挿入部14の先端部が目的部位に到達したところで、媒体供給部から第3バルーン58に水を供給し、第3バルーン58を腸管90に密着させるとともに超音波振動子54を駆動して超音波診断を開始する。 - 特許庁
If a temperature of cooling water is lowered to a target temperature TGT+ΔT at a time t1, PID control with an offset is started, for controlling the opening control signal CNT to become a value determined by adding an offset BCNT to a value determined by PID operation.例文帳に追加
そして、時間t1において、冷却水の温度が、目標温度TGT+ΔTまで低下したならば、開度制御信号CNTをPID演算で求められた値にオフセットBCNTを加えた値に制御するオフセット付PID制御を開始する。 - 特許庁
In this embodiment, when an item which matches to a predetermined retrieval condition is displayed on a screen of an operation display part 140 after scroll display of a list in which items are enumerated is started, a CPU 10 controls the scroll display at lower speed than usual.例文帳に追加
本実施の形態では、項目が列挙されたリストのスクロール表示が開始されてから、所定の検索条件に一致した項目が操作表示部140の画面に表示されたとき、CPU10は、スクロール表示を通常よりも低速に制御する。 - 特許庁
When it is determined according to the output of the touch sensor of the touch screen 5 that a touch has been started in the area of one on/off button displayed on the display screen of the touch screen 5, the on/off state of the on/off parameter allocated to the on/off button is reversed.例文帳に追加
タッチスクリーン5の表示画面に表示された1つのオンオフボタンの領域にてタッチが開始されたと、タッチスクリーン5のタッチセンサの出力に基づいて判定したときは、そのオンオフボタンに割り当てられたオンオフパラメータのオンオフ状態を反転させる。 - 特許庁
To provide an air puff device for a non-contact tonometer which can shorten a period of time when a subsequent measurement work is started with a simple configuration, and prevent the mist of atomized tears, etc., from being captured into a compression chamber through a nozzle.例文帳に追加
構成が簡単でかつ次回の測定作業に入る際の時間短縮を図ることができ、しかもノズルを通じて圧縮室内に霧化した涙等の霧が取り込まれるのを阻止することのできる非接触式眼圧計のエアー噴射装置を提供する。 - 特許庁
The integrated value of the deviation is included in the conditional variables x, and the integral value to give Cx=0 is computed from the initial period of shifting, and when inertial phase is established, the integral value is reset to the value giving Cx=0 and then the sliding mode control is started.例文帳に追加
前記状態変数xには、偏差の積分値が含められると共に、Cx=0となる積分値を変速初期から演算し、イナーシャフェーズになったときに、積分値をCx=0となる値にリセットしてから、スライディングモード制御を開始させるようにする。 - 特許庁
When the inspection holding is set, the output of the image information posterior to the image processing is automatically held, and the output of the image information is started after the inspection holding is released so that a plurality of images related with the same inspection can be outputted as a series of images posterior to the image processing.例文帳に追加
検査保留であると、画像処理後の画像情報の出力が自動的に保留され、検査保留の解除後に出力を開始するので、同一検査内等の関連した複数画像を一連の画像として画像処理後に出力できる。 - 特許庁
When a game is started, game balls to be loaded are apportioned one by one to three loading devices 521a-521c in a loading number apportioning process (S813), so that the number of game balls to be loaded by the loading devices 521a-521c can be almost equalized.例文帳に追加
遊技の開始に当たり、投入すべき遊技球を、投入個数振分処理(S813)により3台の投入装置521a〜521cに対して1ずつ振り分け、その投入装置521a〜521cで投入する遊技球の数をほぼ均等にすることができる。 - 特許庁
Before a prescribed time when the coating of current color is finished, the supply of the current color coating material is stopped and the supply of air to the 1st color change valve unit 16 is started to push out the current color coating material in the coating hose to the coating gun while controlling the air pressure.例文帳に追加
現行色の塗装を終了する所定時間前に、現行色塗料の供給を停止するとともに、第1カラーチェンジバルブユニット16へエアーの供給を開始し、このエアー圧を制御しながら塗料ホース内の現行色塗料を塗装ガンへ押し出す。 - 特許庁
After that, NAND strings to be written out of a NAND string group sharing bit lines are selected, while a potential of each bit line is set to a potential in accordance with write-in data, effective write-in operation of data for a memory cell is started.例文帳に追加
この後に、ビット線を共有するNANDストリング群の中から書き込み対象のNANDストリングを選択すると共に、各ビット線の電位を書き込みデータに応じた電位に設定して、メモリセルへの実効的なデータの書き込み動作を開始する。 - 特許庁
Further, when the release button is pressed full to set a status S2, main photographing is started (time t3), processing, from exposure to storage of picture data into a memory, included in the photographing processing, picture processing and picture recording processing are performed, and a photographed picture file (Pict0102. jpg) is recorded within the memory card.例文帳に追加
さらに、レリーズボタンの全押しにより状態S2となると、本撮影を開始し(時刻t3)、撮影処理に含まれる露光からメモリへの画像データの記憶までと、画像処理と、画像記録処理とを行い、撮影画像ファイル(Pict0102.jpg)をメモリカード内に記録する。 - 特許庁
When the reference signal is started to change according to the change of the air-fuel ratio toward a rich side, the voltage value Vin of the reference signal stored before the number of times of acquisition corresponding to a preset RichDelayTime is read, and output as the voltage value Vout of the present degradation signal.例文帳に追加
そして、空燃比のリッチ側への変更に伴い基準信号が変化し始めたら、予め設定されたRichDelayTimeに相当する取得回数前に記憶した基準信号の電圧値Vinを読み出して現在の劣化信号の電圧値Voutとして出力する。 - 特許庁
Water pressure in a main valve 41 is lower than set pressure and so a passage between a water pipe 5 and a main water flow path 30 is kept in an opened condition and the water supply is started from the second sub water flow path 32 as well as the main water flow path 30 to the water storage tank 1.例文帳に追加
また、主弁41内の水圧が設定圧力より低くなるので、水道管6とメイン流水路30の間が開状態になり、第2のサブ流水路32とともにメイン流水路30からも貯水槽1への給水を開始する。 - 特許庁
When an application procedure is started, a user is requested to specify equipment to be discarded, and when equipment to be discarded is specified, it is determined whether or not the size of the equipment exceeds standards for weight and size of a home delivery company which transfers the equipment to be discarded from the user.例文帳に追加
申し込み手続きを開始すると、破棄対象機器の指定がユーザに要求され、破棄対象機器を特定すると、ユーザの下からから破棄対象機器を搬送する宅配業者の重量やサイズの基準を超過しないか否かを判断する。 - 特許庁
A control frequency deciding means is provided in a power control program, and whether or not various functions for switching should be started is decided according to the past number of times of switching and the current processor operating conditions so that it is possible to prevent the number of times of switching from being made excessive.例文帳に追加
制御頻度決定手段を電力制御プログラム中に設けて、切換のための諸機能を起動するか否かを過去の切換回数及び現在のプロセッサ動作状況に従って決定することにより、切換回数が過多となる事を防止する。 - 特許庁
The start testing apparatus is constituted in such a way that a starter model part which simulates a starter characteristic in advance is installed at a controller used to control the dynamometer and that the engine is started by the output signal of the starter model part until the detected shaft torque characteristic of the engine is inverted and finishes the start.例文帳に追加
ダイナモメータを制御する制御装置に予めスタータ特性を模擬したスタータモデル部を設け、検出されたエンジンの軸トルク極性が反転し、始動完了までスタータモデル部の出力信号によって始動するように構成したものである。 - 特許庁
When the remote-controlled terminal is removed from the charge part 2 , a timer 23 is started to count, and after a predetermined time elapses, a control section 20 is made to give an alarm announcing that the remote-controlled terminal 3 has to be charged through a buzzer 25 and an LED 26 or the like.例文帳に追加
リモコン端末が車載充電部2から取り外されると、タイマ23をのカウントを開始し、所定時間経過後に制御部20はブザー25やLED26等により、そろそろリモコン端末3を充電する必要がある旨のアラーム報知を行わせる。 - 特許庁
To solve such a problem in the conventional power generation systems that, when a state of large power consumption of an external power load such that there is possibility of exceeding the upper limit value of power (for example, contract power) supplied from a power system is continued, a power generation system cannot be started for such a period.例文帳に追加
従来の発電システムでは、電力系統から供給される電力の上限値(例えば、契約電力)を超えるおそれがあるような、外部電力負荷の消費電力が大きい状態が継続すると、発電システムは、その間、起動できない。 - 特許庁
When a cooking timer corresponding to a selected cooking menu is started (S5) and the cooking timer discriminates (S6) time-up, a burner controller stops (S7) heating by a burner, opens a pressure value, opens the inside of an oil tank to the outdoor air and releases a pressure.例文帳に追加
S5で、選択された調理メニューに応じた調理タイマがスタートし、S6の判別で調理タイマがタイムアップすると、S7でバーナコントローラはバーナによる加熱を停止させると共に、圧力弁を開弁させて油槽内を外気に開放し、圧力を逃がす。 - 特許庁
When a stage mounted with the work W is manually operated to move to a prescribed position 83 at which an image of a hole part to be measured 77 (a part to be measured) of the work W is indicated by a mark 85 and halted for a prescribed time, measurement is automatically started.例文帳に追加
ワークWが載置されたステージを手動操作により移動させて、ワークWの測定をすべき穴部77(測定箇所)の画像が目印85で示される所定位置83に到達し、そこで、所定時間静止すると、測定が自動的に開始される。 - 特許庁
To prevent the occurrence of uncomfortable noise caused by mutual rubbing of component members such as a liquid crystal panel, a diffusion plate of a backlight unit, a reinforcing plate, a frame and a reflector due to thermal expansion after the liquid crystal display device is started up, relating to a countermeasure against sound in a liquid crystal display device.例文帳に追加
液晶表示装置における音対策に関し、液晶表示装置起動後の、液晶パネル、バックライトユニットの拡散板、補強板、フレーム、反射板等各部材の熱膨張による相互の擦れで生じる不快音の発生を防止すること。 - 特許庁
In the foaming process, the molten foamable resin 70 at a weld producing part (a part corresponding to a weld part of the foamed resin molding) 23 is pressurized once and then the molding die 4 is moved in the die opening direction and foaming of the molten foamable resin 70 is started.例文帳に追加
発泡工程では、ウエルド発生部(発泡樹脂成形品のウエルド部分に対応する部分)23の溶融発泡性樹脂70を一旦加圧した後に、成形型4を型開き方向へ移動させて溶融発泡性樹脂70の発泡を開始する。 - 特許庁
When determining that the started application is in a landscape mode in step S14, processing proceeds to step S16, and the keys b1-b6 are assigned to functions assigned to each of the keys b1-b6 in the "turn close state (landscape)" of the key assignment table.例文帳に追加
ステップS14にて、起動されたアプリケーションが横長表示であると判定された場合には、処理をステップS16に移し、キーb1〜b6の割り当てを、キー割り当てテーブルの「ターンクローズ状態(横)」のキーb1〜b6各々に割り当てられたキー操作機能とする。 - 特許庁
The following gear 6 is displaced along with movement of an ink head 1 in a thrust direction to selectively engage the paper supply gear 21 with the swinging gear 41 so that the rotation of the paper feed ear 2 is started after the recording papers P... are pressed against the paper feed roller 21 by the swinging movement of the swinging plate 4.例文帳に追加
インクヘッド1の移動により従動ギヤ6を軸長方向に変位させ、給紙ギヤ21と揺動ギヤ41に選択的に噛合させて、給紙ローラ2が、揺動板4の揺動により記録紙P,P…が押し付けられた後に回転を開始するように構成する。 - 特許庁
When restart is detected from an idling-stop page state, while a vehicle is stopped with both an engine 1 and a generator motor A stopper, the generator motor A is started to drive an oil pump 15 and generate a line voltage needed to control the speed change of a CVT 4.例文帳に追加
エンジン1と発電用モータAとの双方が停止されている停車時アイドル停止状態から再発進が検出されたときは、発電用モータAを起動させてオイルポンプ15を駆動し、CVT4の変速制御に必要なライン圧を発生させる。 - 特許庁
It is possible to make the best use of the display control and LCD in the process of a jackpot, and the game player is given a feeling of expectation for whether or not a jackpot occurs according to the result of the variable display started after the jackpot in the process of the jackpot.例文帳に追加
大当たり中における表示制御およびLCDを活かすことができると共に、遊技者には、大当たり中にその大当たり後に開始される変動表示の結果によって大当たりが発生するか否かの期待感を抱かせることができる。 - 特許庁
A rotating drum 1 is started up at a rotating speed which laundries can easily cling to the internal wall during the spin-drying operation and when the balance of clothes is assessed unacceptable at a prescribed number of rotations it changes the value for assessing the balance of the clothes and restarts the spin-drying operation.例文帳に追加
脱水動作において回転ドラム1をその内周壁に洗濯物が張り付きやすくなる回転速度で立ち上げ、布バランスの判定が所定回数満足されない結果になったとき、布バランスの判定値を変更して再度脱水動作を実行する。 - 特許庁
Based on the determination as to whether or not the special game condition is started, the CPU 75 determines which of bonus games with different degrees of advantages to the player is provided, and the liquid crystal display device 4 provides effects indicating the determination.例文帳に追加
CPU(75)は、特別遊技状態へ移行するか否かの決定結果に基づいて、遊技者にとって有利さの度合いが異なる複数の時短のいずれにするか否かを決定し、液晶表示装置(4)は、この決定結果を報知する演出を行う。 - 特許庁
In a liquid ejecting head, a liquid passage 10 having a bubble generating region 11 except an ejection nozzle 18 becomes a substantially closed space by virtue of the contact of a displaced movable member 31 with a stopper 64 and extinguishing of bubbles is started in the closed space condition.例文帳に追加
変位した可動部材31とストッパ64との接触によって、気泡発生領域11を有する液流路10が吐出口18を除いて、実質的に閉じた空間になり、この閉空間状態で気泡の消泡を開始する液体吐出ヘッドである。 - 特許庁
That is, in the both-side printing mode, the measurement value of the counter until attaining the timing when the rotation speed of the cooling fan 60 is switched is set so as to increase as the temperature in the image forming apparatus when the continuous printing of recording paper is started becomes lower.例文帳に追加
すなわち、両面印刷モードでは、記録紙の連続印刷が開始されるときの画像形成装置の内部の温度が低いときほど、冷却ファン60の回転速度が切り換わるタイミングに達するまでのカウンタの計測値が多くなるように設定される。 - 特許庁
In a device for starting the engine by controlling transference of LOCK, OFF, ACC, IGN, ST and RUN to power source position when an engine start switch 10 is pushed, the engine is started by a starter motor 51, and when start of the engine is determined, an ESCL 40 unlocks steering lock.例文帳に追加
エンジンスタートスイッチ10が押されると、LOCK、OFF、ACC、IGN、ST、RUNの各電源ポジションへの移行を制御して、エンジンを始動させる装置において、スタータモータ51によりエンジンの始動処理を行い、エンジンが始動したと判定すると、ESCL40により、ステアリングロックをアンロックさせる。 - 特許庁
When a command of starting a video-recording and reproducing program for video recording is checked, a reserved video recording setting program 384 sets a value indicating the start of the video recording and reproducing program 381 is set to a start flag of a reservation monitoring program 385 when video recording is started.例文帳に追加
予約録画設定プログラム384は、録画時に録画再生プログラムを起動するコマンドがチェックされているとき、予約監視プログラム385の起動フラグに、録画を開始したとき、録画再生プログラム381を起動させる旨を示す値を設定する。 - 特許庁
After that, when a start lever 5 is operated and rotation of the reels 3a-3c is started, rotation of the reels 3a-3c is automatically stopped just after the start of a reel constant speed period γ, and the light of the reel temporary reception display parts 10a-10c is extinguished as synchronized with the stop of rotation of the reels.例文帳に追加
そして、その後、スタートレバー5が操作され、リール3a〜3cが回転始動すると、リール定速期間γの開始直後に自動的に各リール3a〜3cが回転停止し、これと同期して、前記リール仮受付け表示部10a〜10cが消灯する。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|