1153万例文収録!

「Set to zero」に関連した英語例文の一覧と使い方(5ページ目) - Weblio英語例文検索


小窓モード

プレミアム

ログイン
設定

設定

Weblio 辞書 > 英和辞典・和英辞典 > Set to zeroの意味・解説 > Set to zeroに関連した英語例文

セーフサーチ:オン

不適切な検索結果を除外する

不適切な検索結果を除外しない

セーフサーチについて

Set to zeroの部分一致の例文一覧と使い方

該当件数 : 619



例文

When a fresh ink tank is detected before the previously set ink tank is exhausted, a printer controller sets the power application count to zero.例文帳に追加

先に設置されたインクタンクが枯渇する前に新しいインクタンクが検出されたら、プリンタコントローラは電力印加カウントをゼロにする。 - 特許庁

The resistor 7 for discharge is set separated at all times from a commercial AC power supply 2, thus reducing power loss to zero.例文帳に追加

放電用抵抗7は常時において商用交流電源2から切り離されているため、ここでの電力損失を零にできる。 - 特許庁

When the space between the ports 20 and 21 is closed, the brake-pressure chamber 17 is not pressurized, the opening valve pressure of the main valve 13 is lowered, and the damping force is set nearly to zero.例文帳に追加

ポート20,21間を閉じると、背圧室17が加圧されず、メインバルブ13の開弁圧力が低下して減衰力がほぼゼロになる。 - 特許庁

Further, a gap of EE ferrite cores of an insulated converter transformer PIT is set to zero, thereby improving the AC/DC power conversion efficiency.例文帳に追加

また絶縁コンバータトランスPITのEE型フェライトコアのギャップをゼロとすることでAC/DC電力変換効率を向上させる。 - 特許庁

例文

When carrying-out of fuel cut is inhibited during deceleration, a ratio of addition of gas fuel is reduced or is set to zero.例文帳に追加

減速時、燃料カットの実行が禁止されたときには、気体燃料の添加割合を減少させるか、若しくはゼロに設定する。 - 特許庁


例文

When the space between the ports 32 and 33 is closed, the back-pressure chamber 30 is not pressurized and the opening valve pressure of the valve 26 is lowered, and the damping force is set nearly to zero.例文帳に追加

ポート32,33間を閉じると、背圧室30が加圧されず、メインバルブ26の開弁圧力が低下して減衰力がほぼゼロになる。 - 特許庁

As a result, roll moment on the suspension member 10 is reduced in various turning conditions, or set to be substantially zero.例文帳に追加

よって、様々な旋回状態においてサスペンションメンバ10に作用するロールモーメントが小さくされ、あるいは実質的に0とされる。 - 特許庁

In a binary signal generating circuit in which a target is set to make DSV values zero, the value of deviation in the DSV values by the modulation system is added to a binary threshold value.例文帳に追加

DSV値を0とすることを目標とする二値化信号生成回路において、変調方式によるDSV値のずれの値を二値化閾値に加算する。 - 特許庁

During an accumulated heat use operation [dashed line portion of (4)], a supplied hot-water temperature T_0 is set to the incoming water temperature Ti so that a heating amount Q is calculated to be 0 (zero).例文帳に追加

蓄熱利用運転中〔(4)の一点鎖線部分〕は、給湯温度Toを入水温度Tiとし、加熱量Qが0(ゼロ)に演算されるようにする。 - 特許庁

例文

When the part sound volume of a generated note-on part is set to zero, a sound source circuit 18 does not assign a sounding channel to the note-on part.例文帳に追加

音源回路18は、発生したノートオンのパートのパート音量がゼロに設定されている場合は、当該ノートオンへ発音チャンネルを割り当てない。 - 特許庁

例文

To provide a photoelectric oscillator which is capable of oscillating in an arbitrary bias condition and, particularly, capable of generating an optical 2-tone signal with a bias point set to zero.例文帳に追加

任意のバイアス条件での発振、特に、バイアス点をゼロに設定して光2トーン信号を生成することができる光電気発振器を提供する。 - 特許庁

In the method, an interface configured to connect a noninvasive blood pressure sensor and an invasive blood pressure monitor is set to zero.例文帳に追加

非侵襲性血圧検出装置と侵襲性血圧監視装置との間を接続するように構成されたインターフェースを零に合わせる方法に関する。 - 特許庁

If |Itadd|≥Tlimit2, Pin and Pout are both set to zero to stop input/output regardless of whether the |current value I| at that time is larger than Its or not.例文帳に追加

また、|Itadd|≧Tlimit2である場合には、そのときの|電流値I|がItsよりも大きいか否かに関係なく、Pin=0、Pout=0と設定して入出力を停止する。 - 特許庁

When braking is sufficient, advance to a step 250 is carried out, and the execution request flag of brake assist control is turned off, and the target acceleration is set to be zero.例文帳に追加

一方、ブレーキが十分な場合は、ステップ250に進み、ブレーキアシスト制御の実行要求フラグをオフにし、目標加速度を0に設定する。 - 特許庁

When the first control part is in operation, the gain of the output of the second control part is set to be zero when the output of the first control part is greater than or equal to a prescribed value.例文帳に追加

そして、第1制御部が作動している場合には、第2制御部の出力のゲインを第1制御部の出力が所定値以上でゼロとする。 - 特許庁

The magnetic field generation means generates a magnetostatic field to be superimposed nearly in parallel with a center axis where the two-dimensional high-frequency multipole electric field is set nearly to zero.例文帳に追加

磁場発生手段は、2次元高周波多重極電場が略ゼロとなる中心軸に略平行に重畳させる静磁場を発生させる。 - 特許庁

In vehicular environment where snow enters between each of the pads 21, 22 and the disc rotor 19 to cause the lowering of the brake ability, a pad clearance is set to zero.例文帳に追加

このことにより、パッド21,22とディスクロータ19との間に雪が入ってブレーキ能力が低下する車両環境ではパッドクリアランスを「0」とする。 - 特許庁

The difference in relative positions to the magnetic pole of the coils of same phase in the coil units 1A 1B, and 1C is set to be 60°for three-phase, with near zero being preferred.例文帳に追加

各コイルユニット1A,1B,1C内の同相のコイルの磁極に対する相対的位置の差を三相の場合は60°とし、望ましくはほぼゼロにする。 - 特許庁

The “Action Plan to Create Low Carbon Society” has set the target to keep the share of zero-emission power sources at 50% or higher, and the role of nuclear energy is of great importance.例文帳に追加

「低炭素社会づくり行動計画」において、ゼロエミッション電源を50%以上とする目標を掲げており、原子力の役割が重要。 - 経済産業省

On the other hand, when actual air fuel ratio A/F is leaner than a predetermined value af(0), delay time TD is set to zero and scavenging start rotation speed NE2 at a time of natural recovery is set to a predetermined value B lower than the predetermined value A.例文帳に追加

一方、実空燃比A/Fがaf[0]よりもリーンであるときは、ディレー時間T_Dをゼロに設定し、自然復帰時の掃気開始回転数NE2を所定値Aに比して低い所定値Bとなるように設定する。 - 特許庁

After that, the driving of the motor 127 according to the set motor rotation direction pattern is set till it is determined that the value in the motor return control timer is zero, so that the motor 127 is stopped after the rotary body is returned to its initial position.例文帳に追加

その後、モータ復帰制御タイマ値が「0」と判定されるまでモータ回転方向パターンに従ったモータ127の駆動設定を行うことで、回転体を初期位置に戻してから停止させる。 - 特許庁

On the other hand, the timing setting portion 105 outputs a signal Sv to the phase comparator 101 as the reset cancellation timing is set prior to the zero cross timing after a delay time set in advance passes.例文帳に追加

一方、タイミング設定部105は、リセット解除タイミングをゼロクロスタイミングより前に設定するため、予め設定された遅延時間経過後に、信号Svを位相比較器101に出力する。 - 特許庁

When a sample is made to be a film or flake-shaped powders, a torque gradient dT/dHex to an outside magnetic field Hex becomes a linear function in which an origin of a dimension ratio L/D of those is set to zero.例文帳に追加

外部磁界Hexに対するトルク勾配dT/dHexは、試料を膜またはフレーク状粉末としたとき、それらの寸法比L/Dの原点をゼロとした一次関数となる。 - 特許庁

A bit stream replacement section 300 applies error correction to the coded data on the basis of the replacement information to produce a bit stream 50 without errors wherein zero is set to the flag.例文帳に追加

ビットストリーム置換部300は、置換情報に基づいて符号化データのエラー訂正を行って、上記のフラグが0にセットされたエラーの無いビットストリーム50を生成する。 - 特許庁

When an exposure correction amount except zero is set, a CPU 31 reflects the set exposure correction amount and corrects a brightness standard value Bstd to a brightness parameter.例文帳に追加

CPU31は、0以外の露出補正量が設定されている場合には、設定されている露出補正量を反映して明度パラメータに対する明度基準値Bstdを修正する。 - 特許庁

Alternatively, it is possible to envisage that the phase at constant voltage will be terminated when the increasing current reaches a pre-set value and the phase at zero voltage is maintained for a pre-set time.例文帳に追加

あるいは、増加した電流が所定値に達してゼロ電圧での相が所定時間維持されるときに、定電圧での相が終了することを想定することは可能である。 - 特許庁

When an exposure correction amount other than zero is set, a CPU 31 corrects a standard brightness value Bstd to a brightness parameter by reflecting the set exposure correction amount in the parameter.例文帳に追加

CPU31は、0以外の露出補正量が設定されている場合には、設定されている露出補正量を反映して明度パラメータに対する明度基準値Bstdを修正する。 - 特許庁

The liquid crystal application voltage-luminance characteristics of the display part has a luminance change zero area in which a change of luminance with respect to changes in the voltage applied to liquid crystal is almost zero, and reference voltages V9 (positive) and V10 (negative), corresponding to the maximum gradation (white display 255 gradations) are set in the luminance-change zero area.例文帳に追加

前記表示部の液晶印加電圧−輝度特性が、液晶印加電圧の変化に対する輝度の変化がほぼゼロである輝度変化ゼロ領域を有していて、その輝度変化ゼロ領域内に、最高階調(白表示、255階調)に対応する基準電圧V9(正)とV10(負)が設定される。 - 特許庁

When the subtracted result is positive or zero, the subtracted result is set to the holding means 2, an integer inclination value C3+1 is added to a value outputted the last time and the added result is set to an output register 6.例文帳に追加

減算結果が正または零のとき、減算結果を上記保持手段2に設定するとともに、前回出力した値に傾き整数値C3+1を加算して、加算結果を出力レジスタ6に設定する。 - 特許庁

To provide a cold region water meter box with a water activating function, which enables water to be activated concurrently while preventing freezing of a water supply pipe and protecting a water meter, in a cold region having atmosphere temperature set below zero (zero degree C or less).例文帳に追加

大気温が氷点下(摂氏0度以下)となる寒冷地において、給水管の凍結防止と量水器の保護を行うと同時に水の活性化を図ることが可能な活水機能付き寒冷地用量水器ボックスを提供する。 - 特許庁

When the bit 7 (block protection) of the protective register is enabled (set to zero), the contents of a primary security section 214 made non-readable and non-writable.例文帳に追加

1次セキュリティ・セクション214の内容は、保護レジスタのビット7(ブロックプロテクト)がイネーブル(ゼロにセット)されると、読取り不可で書込み不可にされる。 - 特許庁

When the set value X is determined as zero, the DSP unit 16 is designed to output each melody data as it is without performing a sound image localization process.例文帳に追加

設定値Xが0であると判断すると、DSP部16は、音像定位処理を行わずに、各メロディデータをそのまま出力する。 - 特許庁

This invention is applied to a lathe wherein a tool rest 5 is swiveled by a servomotor 16 and clamped by a coupling 17, with motor torque set at zero after clamping is finished.例文帳に追加

サーボモータ16で刃物台5を旋回させ、カップリング17でクランプし、クランプ完了後にモータトルクを零とする旋盤に適用される。 - 特許庁

When there is no magnetic material in the primary magnetic field in the detection region, the output signal of a receiving coil is set to zero or at a micro value.例文帳に追加

検出領域の一次磁界中に金属体が存在しないときには、受信コイルの出力信号を零ないし微小量にする。 - 特許庁

No power control is performed during operation of the motor, but the power command value is set to be zero or 5-6% of nominal power during braking.例文帳に追加

また、電動時は電力制御を行わず、制動時は電力指令値をゼロもしくは定格電力の5%〜6%に設定する。 - 特許庁

The zero flag is one of the control flags stored in the CPU, and it is automatically set or reset according to the result of a comparison operation.例文帳に追加

ゼロフラグは、CPUが内蔵する制御フラグのうちの1つであり、比較演算の結果に応じて自動的にセット/リセットされるフラグである。 - 特許庁

In this case, if the actual charge amount is more than the target charge amount, the target charge and discharge current is set at zero to prevent overcharge.例文帳に追加

この場合、実充電量が目標充電量以上あれば、目標充放電電流をゼロに設定して過充電を防止する。 - 特許庁

On the contrary, if the maximum value max is equal to or more than the threshold, the summed image sum is cleared and set at zero (step S5), and then, and a refresh operation is performed.例文帳に追加

一方、最大値maxが閾値以上であれば、積算画像sumをクリアして0とした後(ステップS5)、リフレッシュ動作を行う。 - 特許庁

The selected tap of the decision feedback filter (26) is set to zero when the signal is equalized in the period of an initial blind operating mode.例文帳に追加

デシジョン・フィードバック・フィルタ(26)の選択されたタップは、信号が初期ブラインド・オペレーティング・モードの期間に等化されるときに、ゼロ値に設定される。 - 特許庁

Accordingly, the comatic aberrations, produced as the objective lens unit 50, can be set to almost zero free, from the value of tilt angle θ of the diffraction lens 2.例文帳に追加

よって、回折レンズ2の傾斜角θの値に関わらず、対物レンズユニット50として発生するコマ収差を略ゼロとすることができる。 - 特許庁

Notification by a notifying means 105f is appropriately performed to bring the put-out rate of tokens close to the value predetermined for every set value because the notification probability is variably set to bring the count value of a difference number counter 752 close to zero.例文帳に追加

差枚数カウンタ752のカウント値が0に近づくように報知確率が可変設定されるため、メダルの払出率が各設定値ごとに予め定められた値に近づくように、報知手段105fによる報知が適正に行われる。 - 特許庁

In this zero calibration method, the introduced gas is subjected to a specific gas kind discrimination treatment, and when the gas satisfies the specific condition, it is recognized automatically that the gas is a gas for zero calibration, and a concentration indication value by the gas is set as the zero point.例文帳に追加

ゼロ校正方法は、導入されたガスについて特定のガス種判別処理を行い、当該ガスが特定の条件を満足するものである場合に当該ガスがゼロ校正用ガスであることを自動的に認識し、当該ガスによる濃度指示値を零点として設定する。 - 特許庁

A microcomputer 25 detects the off-set of the differential amplifying circuit 32 from a terminal T4 of the current detecting circuit 111, and outputs an analog control signal to bring the off-set into zero, so as to remove the off-set in the current detecting circuit 111 in a terminal T3.例文帳に追加

マイコン25は、電圧検出回路111の端子T4から差動増幅回路32のオフセットを検知して、オフセットが「0」となるようなアナログ制御信号を出力して、端子T3に、電流検出回路111でのオフセットを除去できる。 - 特許庁

The high-pressure discharge lamp LA has a period wherein its end-to-end voltage is substantially set to zero immediately after lighting it, and is so controlled that a current flowing between both ends for connecting the discharge lamp LA in the period is substantially set to zero by a voltage detection circuit 5 and a control circuit MC.例文帳に追加

高圧放電灯LAは、点灯直後に高圧放電灯電圧が実質的にゼロとなる期間を有するものであって、電圧検出回路5及び制御回路MCにより、該期間の高圧放電灯LAが接続される両端部間に流れる電流を実質的にゼロとなるように制御している。 - 特許庁

When a zero crossing signal generated by the signal generating part 31 is outputted to the control circuit 27, its frequency is estimated in the frequency estimating function 33, and in the signal detecting function 34, a detection period of the next zero crossing signal relative to the detected predetermined zero crossing signal is set, and detection of the next zero crossing signal is carried out only within the detection period.例文帳に追加

信号生成部31にて生成されたゼロクロス信号が制御回路27に出力されると、周波数推定機能33では、その周波数が推定され、信号検出機能34では、検出された所定のゼロクロス信号に対する次のゼロクロス信号の検出期間が設定され、この検出期間内においてのみ、前記次のゼロクロス信号の検出が行われる。 - 特許庁

In the zero point setting method of the roll opening of a vertical rolling mill to roll a steel plate or the like, the roll opening calculated from the rolling load in the vertical rolling mill is compared with the set roll opening value, and the error in setting the zero point of the roll opening is calculated to set the zero point of the roll opening.例文帳に追加

鋼板等を圧延する竪圧延機において、ロール開度の零点を設定するにあたり、該竪圧延機における圧延荷重から算出されたロール開度とロール開度の設定値とを比較して、ロール開度の零点設定誤差を算出することで、ロール開度の零点を設定することを特徴とする、竪圧延機のロール開度の零点設定方法。 - 特許庁

Then, a value for the required torque is corrected to a relative value to reference torque set to a value less than zero, and a value for the estimated MBT torque is also corrected to a relative value to the reference torque.例文帳に追加

そして、要求トルクの値をゼロよりも小さい値に設定された基準トルクに対する相対値に補正するとともに、推定MBTトルクの値も基準トルクに対する相対値に補正する。 - 特許庁

When an extension distance is large, a select signal of an I/F 191 of the memory card 190 is previously set to zero, and it is changed to CMDIN that is output of the CMDINBUF 323 by a first selector 314.例文帳に追加

延長距離が大きい延長距離の場合は、予めメモリカード190のI/F191のセレクト信号を0にして第1のセレクタ314でCMDINBUF323の出力であるCMDINに切り替えておく。 - 特許庁

When a guard or the like changes a signal transmission device (switch) 7 to the ON state, the determination level value of a fingerprint recognition rate set in the personal identification devices 8, 9, and 12 is lowered to zero.例文帳に追加

警備員等が信号送信装置(スイッチ)7をオンにすると、個人識別装置8、9、12に設定された指紋照合率の判定レベル値は零に低下する。 - 特許庁

例文

When the required electricity for the traveling motor 53 exceeds the generated electricity of the fuel cell 10, the generated electricity to the electric load 54 is set to, for example, zero.例文帳に追加

なお、走行モータ53への要求電力が燃料電池10の発電電力を上回っている場合には、電気負荷54への発電電力を例えば0とする。 - 特許庁




  
Copyright © Japan Patent office. All Rights Reserved.
  
Copyright Ministry of Economy, Trade and Industry. All Rights Reserved.
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2026 GRAS Group, Inc.RSS