| 例文 |
speed commandの部分一致の例文一覧と使い方
該当件数 : 1466件
To provide a variable transmission device configured to always maintain and guarantee an appropriate transmission body contact diameter and torque in two transmission wheels using an external command, in order to solve the following problem: when a proper transmission body contact diameter, namely, speed ratio is determined in one of the two transmission wheels, the appropriate contact diameter cannot be always maintained in the other wheel.例文帳に追加
二つの伝達車の内一方車で適正伝達体接触径即ち速比を決定しても他方車で常時適性接触径を保つ保証は無いので、特に他方車側でも適正な伝達体接触径とトルクとを外部指令により常時維持し保証する操作思想を持つ可変伝動装置を提示する。 - 特許庁
Based on the drawing load parameters calculated for each band, the command analyzing section 17 distributes a drawing destination flag to a driver drawing section 18 existing in a host computer 10 for each band, a high speed drawing device existing in a printer or an F/W writing section existing in the printer.例文帳に追加
マンド解析部17はバンド毎に計算された描画負荷パラメータを元に、各バンド毎にホストコンピュータ10内に存在するドライバ描画部18と、プリンタ内に存在する高速描画デバイスと、プリンタ内に存在するF/W描画部とのうちいずれを使用して行うかの描画先フラグを割り振る。 - 特許庁
When a double braking is detected during ABS control (the sixth timing t16), an ECU controls a command current value Id for a pressure intensifying valve, which opens when a WC pressure in a wheel cylinder provided corresponding to wheels is intensified, so that a pressure intensifying speed of the WC pressure in the wheel cylinder is increased.例文帳に追加
ECUは、ABS制御中にダブルブレーキが検出された場合(第6タイミングt16)、車輪に対応して設けられたホイールシリンダ内のWC圧の増圧速度が速くなるように、ホイールシリンダ内のWC圧を増圧させる際に開動作する増圧弁に対する指令電流値Idを調整する。 - 特許庁
A speed difference dependent state quantity calculation part 20 uses command position data on four successive points to compute the difference between the velocity vector connecting the two former points among the four points and the velocity vector connecting the two latter points, and uses the computed velocity vector difference to computes a state quantity depending upon the velocity vector difference.例文帳に追加
速度差依存状態量算出部20においては、連続する4点についての指令位置データを用い、該4点のうちの前半の2点を結ぶ速度ベクトルと、後半の2点を結ぶ速度ベクトルとの差を算出し、該算出した速度ベクトル差を用いて該速度ベクトル差に依存する状態量を算出する。 - 特許庁
The subtraction part 23 and the engine control part 25 drive the driving motor 26 based on a value calculated by subtracting the target driving force calculated by the torque command calculation part 21 when traction control is operated, and control the engine 28 for power generation with a target engine revolution speed value when the traction control is not operated.例文帳に追加
減算部23及びエンジン制御部25は、トラクションコントロール作動時に、トルク指令演算部21が算出した目標駆動力を減算した値に基づいて、駆動モータ26を駆動させるとともに、トラクションコントロールが作動していない場合のエンジン回転数目標値で発電用エンジン28を制御する。 - 特許庁
The apparatus comprises: the position detector for detecting the position of the table; the multi-phase motor for selectively changing-over a coil to be energized in response to the position of the table; an initialization driving current command setting part; a table speed arithmetic part, and a divider.例文帳に追加
上記目的を解決するために本発明では、テーブルの位置を検出する位置検出器と、 テーブルの位置に応じて通電すべきコイルを選択的に切り替える多相型のモータを備えた位置決めテーブル装置において、初期化駆動用電流指令設定部と、テーブル速度演算部と、除算器を設けた。 - 特許庁
To improve a desire for exercise by transmitting a reproducing command signal based on an output signal from exercise equipment by remote control and varying the speed of a reproduced picture projected on the screen of a display in accordance with an exercise quantity so as to improve presence.例文帳に追加
運動機器からの出力信号に基づいた再生指令信号を遠隔操作により送信し、ディスプレイの画面に映し出す再生画像の速度を運動量に応じて可変することにより、臨場感を高めて運動意欲を増すことのできる遠隔操作装置及び情報再生装置を提供する。 - 特許庁
This control device 10 supplying a command signal to a motor 8 driving a high pressure pump 3 controls the rotating speed of the motor 8 on the basis of a feedback signal of fuel pressure from a pressure sensor 9 so as to control fuel pressure in high pressure piping to an optional pressure requested by a cylinder injection engine 1.例文帳に追加
高圧ポンプ3を駆動するモータ8に指令信号を与える制御装置10は、圧力センサ9からの燃料圧力のフィードバック信号に基づきモータ8の回転数を制御して高圧配管内の燃料圧力を筒内噴射エンジン1の要求する任意の圧力に制御する。 - 特許庁
As a simultaneous car run detecting means 1E detects cars 8A and 8B adjacent to each other running in a similar direction at the same timing, a car acceleration regulation means 1F outputs a command to one car 8B for decreasing (or increasing) acceleration without changing the highest speed of it.例文帳に追加
かご同時期走行検出手段1Eで、互いに隣接するかご8A,8Bが同時期に同方向へ走行することを検出すると、かご加速度調整手段1Fは、一方のかご8Bに対して、その最高速度を変更することなく、その加速度を低下(又は上昇)させる指令を出力する。 - 特許庁
A high-speed A/D converting device 8 detects three-phase gate signals Pu, Pv, Pw output from a voltage command PWM modulation device 3 and current response values IuRes, IvRes, IwRes conducted to the synchronous machine 5 by a sampling frequency higher than a switching frequency of a reverse converter 4.例文帳に追加
高速A/D変換手段8で、電圧指令PWM変調手段3から出力される3相ゲート信号Pu、Pv、Pwと、同期機5に導通される電流応答値IuRes、IvRes、IwResを、逆変換器4のスイッチング周波数よりも高いサンプリング周波数にて検出する。 - 特許庁
In this data reading/writing method for the bridge interface, by properly controlling a signal level and timing between a host and a device, the bridge interface can perform a perfect message handshake, and performs work at any transmission speed to easily convert the flow of the command of an arbitrary bus present in the front end.例文帳に追加
本発明は、ホストとデバイスとの間において、信号レベルとタイミングを、適当に制御することにより、ブリッジインタフェースが、完全なメッセージハンドシェイクをでき、何れの伝送速度でも、ワークを行い、簡単に、先端にある任意のバスのコマンドの流れを変換できる、ブリッジインタフェースのデータ読み書き方法を提供する。 - 特許庁
A torque compensation application means 13 for adding a torque compensation value corresponding to the inclined part of the door support member to the torque command (torque control signal) Tpi outputted from the speed controller 8 is provided to suppress acceleration of the door panel in the inclined part when closing the door in order to realize stable door closing operation of the door panel.例文帳に追加
この速度制御器8から出力されるトルク指令(トルク制御信号)Tpiにドア支持部材の傾斜部に対応したトルク補償値を加えるトルク補償印加手段13を設けることで、戸閉時にドアパネルが傾斜部で加速することを抑制して、ドアパネルの安定した戸閉動作を実現する。 - 特許庁
The command q-axis current correction stored in the memory 27 is computed, based on the change of the rotational speed of the motor 4 in the preliminary measurement wherein the motor 4 is driven by connecting a dummy load device that generates the same torque as the torque of the load, under the same control conditions as the actual operation, excluding the point that the correcting operation is stopped.例文帳に追加
記憶部27に記憶される指令q軸電流補正値は、上記補正動作を停止させた点を除いて実運転時と同じ制御条件で、負荷のトルクと同じトルクを発生する擬似負荷装置を接続してモータ4を駆動した事前測定でのモータ4の回転速度の変化に基づいて算出する。 - 特許庁
The switching section 284 uses the high speed clock CLK 3 from the clock conversion section 21 as a switching command, selects one bit each from the 10-bit data of the parallel form according to a prescribed order, provides an output of 1-bit data from an output terminal 284b, converts the parallel data into data of a serial form, and gives the resultant data to an output buffer 286.例文帳に追加
切替部284は、クロック変換部21からの高速クロックCLK3を切替指令として用いることで、パラレル形式の10ビットデータ中から1ビットずつ所定の順序に従って選択して出力端子284bから出力することで、パラレルデータをシリアル形式のデータに変換し、出力バッファ286に渡す。 - 特許庁
An overvoltage suppressing section (16) comprises a power supply voltage setting section (17), a first overvoltage generating section (18) for generating a first overvoltage value from the power supply voltage, and a regeneration suppressing section (19) for relaxing the slowdown rate of a speed command, when a DC voltage signal reaches the first overvoltage value.例文帳に追加
過電圧抑制部(16)は、電源電圧を設定する電源電圧設定部(17)と、電源電圧から第1過電圧値を生成する第1過電圧値生成部(18)と、直流電圧信号が第1過電圧値以上になると速度指令の減速率を緩和する回生抑制部(19)と、を備えた。 - 特許庁
The head driving device for driving heads 13, 52 according to the path set in a production program comprises a means for classifying a torque use level according to the effective load factor of a head driving motor 36, and a means for limiting a speed or acceleration command to the head driving motor 36 according to the classified torque use level.例文帳に追加
生産プログラムに設定された経路に従って、ヘッド13、52を駆動するためのヘッド駆動装置において、ヘッド駆動用モータ36の実効負荷率に応じて、トルク使用レベルを区分する手段と、区分されたトルク使用レベルに応じて、ヘッド駆動用モータ36への速度や加速度の指令を制限する手段と、を備える。 - 特許庁
To set the operation control of a motor generator to the one adapted to a further actual actual work state, etc. by automatically deciding a speed command of a target value when operation is switched to a motor or a generator of the motor generator based on an average output of an engine calculated from a load actually applied to the engine.例文帳に追加
モータジェネレータの電動機または発電機として作動を切り換える際の目標値である速度指令を、エンジンに実際にかかる負荷にから算出されるエンジンの平均出力に基づいて自動的に決定することで、モータジェネレータの作動制御を、より実際の作業状況などに即したものとする。 - 特許庁
To provide a variable speed control device for a transmission with a toroidal continuously variable speed mechanism for achieving shift ratio control in high follow-up response to a target shift ratio with quick shifting operation in such a condition that sudden shifting operation is required at sudden deceleration or acceleration by using feed forward compensation for an actuator command value without causing hunting in normal control or involving the setting of a difficult target shift ratio.例文帳に追加
通常制御でのハンチング発生や困難な目標変速比設定を伴うことのないアクチュエータ指令値のフィード・フォワード補償により、急減速時や急加速時等の急な変速動作が必要な状況において、速い変速速度により目標変速比に対する高い追従応答性による変速比制御を達成することができるトロイダル型無段変速機構を有する変速機の変速制御装置を提供すること。 - 特許庁
To keep a high speed operation cycle by reducing the number of terminals required for command input and the number of terminals required for address input in a method for controlling the operation of a semiconductor memory provided with a plurality of operation modes and in a semiconductor memory provided with a plurality of operation modes.例文帳に追加
本発明は、複数の動作モードを備えた半導体記憶装置の動作制御方法および複数の動作モードを備えた半導体記憶装置に関し、コマンドの入力に必要な端子数、アドレス入力に必要な端子数を低減すること、および端子数の低減によっても高速な動作サイクルを維持することを目的とする。 - 特許庁
Further, the main controller 7 sends a proper command signal to a lens driving device 25 and makes a condenser lens (described in detail later) held on a fine moving stage device 23 turn in X-Y plane by properly operating the fine moving stage device 23 and makes the incident position of a spot laser beam rotate at high speed on a work W.例文帳に追加
また、主制御装置7は、レンズ駆動装置25に適当な指令信号を送信して微動ステージ装置23を適宜動作させることにより、微動ステージ装置23に保持された集光レンズ(後に詳述)をXY面内で回転運動させることができ、スポット状のレーザ光の入射位置をワークW上で高速回転させることができる。 - 特許庁
To achieve higher data compression rate than data compression processing of a conventional slide dictionary system by utilizing a feature of a command code length and to generate a compression code capable of data-developing at a high speed by simple data development processing in a data compression program for compressing data of a program such as firmware of a control unit to be mounted on electronic equipment.例文帳に追加
電子機器に搭載される制御部のファームウェア等のプログラムをデータ圧縮するデータ圧縮プログラムにおいて、命令コード長の特徴を利用して、従来のスライド辞書方式のデータ圧縮処理よりも高いデータ圧縮率を実現すると共に、単純なデータ展開処理により、高速にデータ展開可能な圧縮コードを生成する。 - 特許庁
To provide a method and device, which concurrently compensate the influence of a feed control error, and the synchronous deflection and asynchronous deflection of a turn table and then form a high accurate constant linear speed and constant track pitch spiral-shape of high density information track on an optical original disk with reference to the strictly accurate CLV driving command pulse row.例文帳に追加
本発明は、厳密に正確なCLV駆動指令パルス列を基準に、送り制御誤差及び、ターンテーブルの同期振れ・非同期振れの影響を同時に補償し、光ディスク原盤上に、高精度な等線速・等トラックピッチスパイラル状の高密度情報トラックを形成するための方法及び装置を提供することを目的とする。 - 特許庁
In warm-up control, a basic fuel injection amount is calculated based on throttle opening (a throttle opening command value) TH and an engine speed NE of the general-purpose engine, and the calculated basic fuel injection amount is corrected based on the throttle opening TH to calculate fuel injection amount for warm-up, and thereby to cause an injector to inject fuel (S16, S18).例文帳に追加
汎用エンジンのスロットル開度(スロットル開度指令値)THとエンジン回転数NEとに基づいて基本噴射量を算出すると共に、算出された基本噴射量をスロットル開度THに基づいて補正して暖機時の燃料噴射量を算出してインジェクタから噴射させる暖機制御を実行する(S16,S18)。 - 特許庁
The control unit of the electric power steering system controls the drive of a motor for applying a steering assist force to the steering system by the current command value calculated for a steering torque and a car speed, wherein the function for detecting the one-way flowing of the vehicle and the function for correcting the neutral position of the steering system when the one-way flowing has been detected are provided.例文帳に追加
操舵トルク及び車速に基づいて演算された電流指令値により、操舵系に操舵補助力を付与するモータを駆動制御する電動パワーステアリング装置の制御装置において、車両の片流れを検出する機能と、片流れが検出されたときに、操舵系の中立位置を補正する機能とを設ける。 - 特許庁
The voltage sensor 15 of this fault diagnoser computes the output Pac1 of an AC motor 6 based on three-phase AC voltage commands vu^*, vv^* and vw^* of an inverter 4, and current detected values iu, iv and iw of the current sensors 9a-9c, and computes the output Pac2 of the AC motor 6 based on a torque command Tmg and motor rotational speed ω.例文帳に追加
電圧センサ診断部15は、インバータ4の3相交流電圧指令値vu^*,vv^*,vw^*、および、電流センサ9a〜9cの電流検出値iu,iv,iwに基づいて、交流モータ6の出力Pac1を算出するとともに、トルク指令値Tmg、および、モータ回転速度ωに基づいて、交流モータ6の出力Pac2を算出する。 - 特許庁
When a paper P is fed, commanded predetermined amount of paper sheets is fed, and it is determined that a rear end of the paper P is positioned in a BS driving region (low speed region) ABS, amount of paper feeding of a paper feeding command is divided so that paper feeding ends at an inlet Pb of the BS driving region ABS once and then remaining paper sheets are fed.例文帳に追加
用紙Pを紙送りする際、指令された所定量の紙送りをした場合、用紙Pの後端がBS駆動領域(低速領域)ABS内に位置することになると判断されると、BS駆動領域ABSの入口Pbで一旦紙送りが終わり、その後、残りの紙送りがなされるように紙送り指令の紙送り量を分割する。 - 特許庁
A rope slip determination device 11 starts to count by a timer when a speed command for the car 8 is confirmed, and determines whether a pulse data accumulated value from a period of starting a count exceeds a pulse data threshold set by a roll slip threshold setting device 13 when a count value reaches a time limit value set by a time limit value setting device 12.例文帳に追加
ロープスリップ判定装置11は、乗りかご8の速度指令が確認できた場合にはタイマーカウントを開始し、カウント値がタイムリミット値設定装置12により設定されたタイムリミット値に達した場合には、カウント開始時からのパルスデータ累積値がロープスリップ閾値設定装置13により設定されたパルスデータ閾値を超えているか否かを判定する。 - 特許庁
When a clutch operation tool 17 which is artificially operated to give an operation command is operated from an interruption position to a transmission position, a control device 19 is constituted so that working pressure of the PTO clutch 6 may be operated in proportion to operation speed of the clutch operation tool 17 and the PTO clutch 6 may be operated from the interruption state to the transmission state.例文帳に追加
人為的に操作されるもので操作指令を出すクラッチ操作具17が遮断位置から伝動位置に操作される際において、クラッチ操作具17の操作速度に比例してPTOクラッチ6の作動圧が操作されて、PTOクラッチ6が遮断状態から伝動状態に操作されるように、制御装置19を構成する。 - 特許庁
The anode driving control portion can change the rotating speed of the anode 4 of the X-ray tube during X-ray irradiation, and operates the anode of the X-ray tube in the silence mode in which it rotates at low speeds when it is judged that a silent operation is required on the basis of preset radiographic conditions or when a silent action command is input.例文帳に追加
陽極駆動制御部が、X線照射時のX線管の陽極4の回転速度を変更し得るようになっていて、予め設定された撮影条件に基づき静粛動作が要求されると判定したとき、または、静粛動作命令の入力を受けたとき、X線管の陽極を、低速度で回転する静粛モードで動作させる。 - 特許庁
When the accelerator operating amount drops to 0 in the state that the present accelerator operating amount and the present vehicle speed exist within a hysteresis region D2 and an acceleration slip executing command is output to a lock-up clutch, a counter C1 starts to count-up per constant cycle, and the counter C1 measures the time from when the accelerator operating amount drops to 0.例文帳に追加
現在のアクセル操作量及び車速がヒステリシス領域D2内にあって、且つロックアップクラッチの加速スリップ実行指示がなされている状態でアクセル操作量が「0」となったとき、一定周期毎のカウンタC1のカウントアップが開始され、そのカウンタC1により上記アクセル操作量が「0」になった時点からの時間が計測される。 - 特許庁
If the thrust command correction value is smaller than the predetermined certain operation mode changeover threshold, it is decided that the control object 5 is in a position setting/constant speed state, and the decision result is supplied to the changeover unit 33 in the power amplifier 3 and the changeover unit 33 changes the PWM amplifier 32 to the linear amplifier 31 in the power amplifier 3 according to the decision result.例文帳に追加
また、推力指令補正値が予め設定された一定の動作方式切換閾値より小さい場合は、制御対象5が位置決め整定中・一定速中であると判断し、その判断結果がパワーアンプ3を構成する切換部33に与えられ、この切換部33では判断結果に応じてリニアアンプ31にパワーアンプを切換える。 - 特許庁
An inverter 6 driving an electric motor 4 of the electric compressor 3 performs self-cooling for the inverter by operating in the overheat protection mode driving the electric motor at the rotational speed for thermal protection different from the rotational command value from an air conditioning control device 20 and securing flow rate of the refrigerant when the detection temperature of an inverter temperature sensor 22g exceeds a predetermined value.例文帳に追加
電動圧縮機3の電動モータ4を駆動するインバータ6は、インバータ温度センサ22gの検出温度が所定値を超えると、空調制御装置20からの回転指令値とは異なる熱保護用回転数で電動モータを駆動する過熱保護モードで作動し、冷媒流量を確保してインバータの自己冷却を行う。 - 特許庁
A belt holding pressure target value calculating part 94 determines a belt holding pressure target value Pdr on the basis of a rotating speed ωm of the gear change pump and the gear change control command value u2, besides input torque T_in and the change gear ratio γ, to compensate the lowering of belt holding pressure generated in control by the gear change control system 46.例文帳に追加
ベルト挟圧力目標値算出部94は、入力トルクT_in及び変速比γの他に、変速用ポンプの回転速度ωm及び変速制御指令値u2にも基づいて、ベルト挟圧力目標値Pdrを設定することで、変速制御系46の制御により生じるベルト挟圧力の低下分を補償する。 - 特許庁
When the target speed MRN1* determined to be within a predetermined lock range, the HVECU 100 sets an allowable torque such that a heat loss caused in switching elements during the transition through the lock range will not exceed the heat rating of the switching elements, and sets a torque command TR1 of the motor generator MG1 within the allowable torque.例文帳に追加
目標回転数MRN1*が所定のロック領域内にあると判定されると、HVECU100は、ロック領域の通過期間にスイッチング素子に発生する熱損失がスイッチング素子の熱定格を超えないように許容トルクを設定し、かつ、許容トルクを上限値としてモータジェネレータMG1のトルク指令TR1を設定する。 - 特許庁
An increase quantity DTRQ of engine output torque by minute quantity injection is calculated according to a rise quantity of engine speed (S15, SD16), and a minute command fuel injection quantity QLCMD commanding minute quantity injection is increased (S17, S18) until a torque increase quantity DTRQ reaches a prescribed increased quantity DTRQ0.例文帳に追加
微少量噴射によるエンジン出力トルクの増加量DTRQを、エンジン回転速度の上昇量に応じて算出し(S15,SD16)、トルク増加量DTRQが所定増加量DTRQ0に達するまで、微少量噴射を指令する微少指令燃料噴射量QLCMDを増加させる(S17,S18)。 - 特許庁
The MPU 12 is mounted with both functions of the fuel injection control system 17 and the idle stop control system 18 of expanding an idle stop area up to a speed reduction area before stopping a vehicle, and the idle stop control system 18 is provided with a brake negative pressure monitoring part 26 for monitoring brake negative pressure, and when the brake negative pressure is insufficient, output of an idle stop command is prohibited.例文帳に追加
MPU12に、燃料噴射制御系17と、アイドルストップ領域を車両停止前の減速領域まで拡大したアイドルストップ制御系18の両方の機能を実装し、アイドルストップ制御系18に、ブレーキ負圧を監視するブレーキ負圧監視部26を設け、ブレーキ負圧が不足する場合は、アイドルストップ指令の出力を禁止する。 - 特許庁
The CPU specifies the size of the display area for displaying the special symbols on an image display device by the display control information stored in the control ROM, designates the speed and direction of moving the display area on the display images to specify the images E1, E2, E3, etc. to be displayed and issues the processing command to the VDP.例文帳に追加
CPUは、制御ROMに格納された表示制御情報により、画像表示装置上の特別図柄を表示するための表示領域の大きさを特定し、前記表示画像上での表示領域の移動速度と移動方向とを指定し、これらから表示対象の画像E1,E2,E3....を特定して、VDPに処理コマンドを発行する。 - 特許庁
This robot system includes a robot 107 to be driven by the reduction gear arranged between a servo motor and load, a torque command value for driving the servo motor, a dynamics arithmetic part 108 for performing a calculation from the load, and a reduction gear temperature estimating part 109 for estimating the reduction gear temperature from torque and axial speed calculated from the dynamics arithmetic part 108.例文帳に追加
サーボモータと負荷との間に配置された減速機により駆動されるロボット107と、前記サーボモータを駆動させるトルク指令値と、前記負荷から演算されるダイナミクス演算部108と、前記ダイナミクス演算部108で算出されたトルクと軸速度から減速機温度を推定する減速機温度推定部109を備えたものである。 - 特許庁
A waiting time of a host computer 1 required for carrying and mounting a magnetic tape and program searching is removed and high speed backup processing is realized by transmitting the existence of a magnetic tape and discrimination information of the magnetic tape specified by a mount command referring to data previously stored in a magnetic tape information storing table 8 to a host computer 1.例文帳に追加
予め磁気テープ情報記憶テーブル8に記憶させておいたデータを参照してマウントコマンドで指定された磁気テープの存在の有無および当該磁気テープの識別情報をホストコンピュータ1に送信することで、磁気テープの搬送やマウントおよび頭出しに必要とされるホストコンピュータ1の待ち時間をなくし、高速なバックアップ処理を実現する。 - 特許庁
The base assist command determination means 1 is provided with a dynamic amplitude amplification means 1-1 for amplifying an amplitude according to at least a frequency of a processing object signal, and a static amplitude amplification means 1-2 for amplifying the amplitude according to the frequency of the processing object signal and vehicle speed, in a serially connected state.例文帳に追加
ベースアシスト指令決定手段1は、少なくとも処理対象信号の周波数に応じて振幅増幅を行なう動的振幅増幅手段1−1と、処理対象信号の振幅と車速に応じて振幅増幅を行なう静的振幅増幅手段1−2とを、直列結合した形で、備えることにより課題を解決した。 - 特許庁
A first correction Δθ1 or a correction for a first command value θ1 to control a pilot injection quantity performs a linear interpolation between the value 'Δθ1H' corresponding to 'NPH' and the value 'Δθ1L' corresponding to the 'NPL', whereby the first correction Δθ1 corresponding to the engine speed is calculated.例文帳に追加
パイロット噴射量を制御するための第1指令値θ1に対する補正量である第1補正量Δθ1は、エンジン回転数に基づき、「NPH」に対応する値「Δθ1H」と「NPL」に対応する値「Δθ1L」との間を直線補間することにより、そのエンジン回転数に対応する第1補正量Δθ1を算出される。 - 特許庁
The CPU specifies the size of the display area for displaying the special symbols on the image display device based on the display control information stored in the control ROM, designates the speed and direction of moving the display area on the display image so that the images E1, E2 and E3 and the like to be displayed are specified and then, issues the processing command to the VDP.例文帳に追加
CPUは、制御ROMに格納された表示制御情報により、画像表示装置上の特別図柄を表示するための表示領域の大きさを特定し、前記表示画像上での表示領域の移動速度と移動方向とを指定し、これらから表示対象の画像E1,E2,E3....を特定して、VDPに処理コマンドを発行する。 - 特許庁
When a work content of a work machine is changed from excavation work to hoist work, a valve opening relating to the same operation command value of a closed center valve in a control valve 31 of a hydraulic circuit actuating the work machine is switched so as to reduce it, and an operating speed of a hydraulic actuator operated by hydraulic fluid supplied from the closed center valve is reduced.例文帳に追加
作業機械の作業内容を掘削作業から吊り作業へ変更するときに、作業機械を作動する油圧回路のコントロールバルブ31におけるクローズドセンタ弁の同一操作指令値に対する弁開度を減少させるように切換え、クローズドセンタ弁から供給した作動油により作動する油圧アクチュエータの作動速度を低下させる。 - 特許庁
The motor control apparatus includes a PI control part 1 for controlling the speed of a motor 4, a brake device 8 for preventing dropping of a shaft based on brake signal, and a storage part 7 which detects the brake signal input in a brake device 8 and stores torque command value T* calculated by the PI control part 1 based on the state of detected brake signal.例文帳に追加
モータ制御装置は、モータ4の速度を制御するPI制御部1と、ブレーキ信号に基づいて軸の落下を防止するブレーキ装置8と、ブレーキ装置8に入力されるブレーキ信号を検出するとともに、検出されたブレーキ信号の状態に基づいて、PI制御部1により算出されたトルク指令値T*を記憶する記憶部7とを備える。 - 特許庁
An output voltage of the inverter 5 can be made maximum by compensating a phase difference between the voltage command value v* and the tertiary harmonic by the tertiary phase compensation part 19, and the voltage utilization factor of the inverter 5 can be improved without causing the cost increase of an operation means such as a microcomputer by simple operation, thus achieving the high-speed operation of the motor 4.例文帳に追加
この3次調波位相補償部19により、電圧指令値v*と3次調波との位相ずれを補償することでインバータ5の出力電圧を最大とすることができ、簡単な演算によりマイコンなどの演算手段のコストアップをせずにインバータ5の電圧利用率を向上させ、電動機4の高速運転を実現できる。 - 特許庁
Concerning the failure determination on the frictional element, only when the command shift stage is a first speed established by engagement of one low clutch LOW/C and a one-way clutch, one frictional element which is disengaged due to failure or engaged due to failure is specified, whereby the failure contents are determined accurately and in detail to suitably set the avoidance shift stage.例文帳に追加
摩擦要素の故障判定については、指令変速段がロークラッチLOW/C1つとワンウエイクラッチの締結により成立する第1速であるときのみ、故障解放あるいは故障締結した摩擦要素を1つに特定するので、故障内容を正確、詳細に確定して適切に回避変速段を設定することができる。 - 特許庁
Even when the wobble signal Sw cannot be obtained normally during stop processing of the optical disk, if a first elapse time T1 elapses by a prescribed time Tc, a control part 20 transmits a spindle stop command Cs to a DSP 22, so that the high speed reverse rotation of the spindle motor 26 is prevented, and the spindle motor 26 can be stopped.例文帳に追加
光ディスク停止処理時にウォブル信号Swが正常に得られない場合でも、第1の経過時間T1が所定時間Tcを経過すれば、制御部20はDSP22にスピンドル停止コマンドCsを送信するため、スピンドルモータ26の高速逆回転を防止するとともに、スピンドルモータ26の停止を行うことができる。 - 特許庁
In the operation data, a speed change mode on the point of velocity switching, in short, on whether it is at the finish of an isokinetic section or at the start of the isokinetic section in the next operation section that it achieves a position command value is registered in every operation section.例文帳に追加
動作データには、動作の区間終了時の移動距離を特定するための位置データと、等速移動している際の速度データ等とともに、速度の切り替わるポイント、つまり、位置指令値を達成するのが、等速区間の終了時点か、次の動作区間の等速区間の開始時点かの速度変更モードを動作区間毎に登録する。 - 特許庁
The compensation calculating part 5 determines polarity in the direction of rotation and the timing of reversal in the direction of rotation according to speed commands, adds the polarity in the direction of rotation multiplied by the set lost-motion compensation value to a position command as the amount of lost-motion compensation, and changes the value of the integrator 9 to a desired compensation value at the timing of reversal.例文帳に追加
補償算出部5は、速度指令に基づいて回転方向の極性と回転方向を反転する反転タイミングとを判別して、回転方向の極性とロストモーション補償設定値との乗算値をロストモーション補償量として位置指令に加算し、反転タイミングにおいて積分器9の値を補償用目標値に変更する。 - 特許庁
To obtain a target display system which displays target information so that the target information regarding a target object is generated from different kinds of detection results at a high speed with high precision and the target object can speedily and effectively be monitored and handled by applying this system to, specially, a command control system, a guard system, etc.例文帳に追加
特に指揮統制システムや警備システムなどに適用し、複数種の検知結果から目標対象に関する目標情報を高速かつ高精度に生成して、目標対象に対する監視や対処を迅速かつ効果的に実行できるように当該目標情報を表示する目標表示システムを提供することにある。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|