Compressorを含む例文一覧と使い方
該当件数 : 22706件
Ports of an accumulator 27 as equipment forming the refrigerant circuit 20 of the GHP includes an outflow port allowing gas refrigerant to flow to a compressor 21, an inflow port allowing the refrigerant passed through the refrigerant auxiliary evaporator 28 for waste heat recovery to flow therein, and an inflow port allowing the refrigerant flowing through a bypass tube 29 bypassing the refrigerant auxiliary evaporator 28 to flow therein.例文帳に追加
GHPの冷媒回路20を構成する機器であるアキュムレータ27のポートとして、圧縮機21に向けてガス冷媒を流出する流出ポート、排熱回収用の冷媒補助蒸発器28を通過した冷媒が流入する流入ポート、冷媒補助蒸発器28をバイパスするバイパス管29を流通する冷媒が流入する流入ポートを備えさせる。 - 特許庁
This method includes a step to operate an excimer or molecular fluorine laser system, a step to measure a temperature corresponding to a temperature of a magnetic compressor including at least one stage capacitor of the discharge circuit, and a step to calculate a corrected delay offset value including a delay dependence corresponding to a capacitance dependence of at least one stage capacitor on the measured temperature.例文帳に追加
前記エキシマー又は分子弗素レーザシステムを動作するステップと、前記放電回路の少なくとも1個の段キャパシタを含む磁気圧縮器の温度に対応する温度を測定するステップと、前記少なくとも1個の段キャパシタの前記測定された温度における容量依存性に対応する遅延依存性を含む補償遅延オフセット値を計算するステップとを含む。 - 特許庁
To compose a circuit minimizing power recovery loss while matching flow rate and work by using an expansion machine of simple structure type although a complicated expansion ratio control means is required since an expansion machine requiring valve open and close control such as a reciprocating type is used coaxially with a compressor in an existing supercritical cycle refrigerating air conditioning device.例文帳に追加
超臨界サイクルの冷凍空調装置において、従来はレシプロ式のような弁開閉の制御が必要な膨張機を圧縮機と同軸で用いていたので、複雑な膨張比制御手段が必要であったが、機構が簡素な形式の膨張機を用いるために流量と仕事をマッチングさせながら動力回収ロスが極力小さくなるような回路を構成する。 - 特許庁
By this, an existing problem with the control device wherein the start of cooling/heating is delayed since the compressor is started after the measurement of the response delay time which requires a specified time can be solved.例文帳に追加
圧縮機起動直前に駆動回路の応答遅れ時間を測定し、その後、圧縮機を起動する場合と、圧縮機起動直前に応答遅れ時間を測定せずに圧縮機を駆動する場合の2つの方式を切換えるようすることで、最低限、応答遅れ時間を測定する必要がある場合のみ圧縮機起動前に応答遅れ時間測定を行い、それ以外は応答遅れ時間を測定しない。 - 特許庁
This production process is more effectively carried out in cases such that the incidental equipment of the fluidized bed reactor is operated at equal pressure to the fluidized bed reactor and being in the range of 0.5-10 MPaG, the inert gas is nitrogen, or a single step or multi-step reciprocating type oilless compressor is used for elevation of the inert gas pressure.例文帳に追加
前記流動床反応器の付帯設備が流動床反応器と同等の圧力で運転される付帯設備であり、かつ、その圧力が0.5MPaG〜10MPaGの範囲である場合、前記不活性ガスが窒素である場合、前記不活性ガスの昇圧に際して、単段、もしくは複数段の往復タイプの無給油型コンプレッサーを用いる場合は、本発明は一層効果的に実施される。 - 特許庁
To provide a hermetic compressor that ensures safety by enhancing and stabilizing the mechanical strength of an electrical component cover 5 without changing the shape and size of the electrical component cover, while utilizing an existing mold for injection molding an electrical component cover 5, as well as reducing cost and improving moldability of the electrical component cover.例文帳に追加
電装品カバーの形状寸法を変更することなく、また、電装品カバー5を射出成形する金型についても既存の金型をそのまま使用して、電装品カバーの機械強度の向上と安定を図ることを可能にすると同時に、電装品カバーの更なる低コスト化と成形性向上をも可能にし、確実に安全性を実現する密閉型圧縮機を提供する。 - 特許庁
And, high density flow concrete force-fed through a pressure-resistant concrete hose by a concrete force-feeding device is dispersed and jetted form the tip of a jetting spray nozzle through the compressed air supply pipe and compressed air feeding pipe 16 by an air compressor and is immediately adhered to surface to be sprayed.例文帳に追加
そして、コンクリート圧送装置により高耐圧コンクリートホースを介して圧送されて来た高密度流コンクリートを、エアコンプレッサーより圧縮空気供給パイプ、圧縮空気送給パイプ16を介して供給口より吹付ノズル内に供給された、液体急結剤を含んだ圧縮空気によって分散、吹き飛ばし吹付ノズル先端より噴出させて、直ぐに被吹付面に付着させる様にする。 - 特許庁
To enable to cool foods at a low cooling cost without the need of a relatively large chilled water producing unit as a conventional chiller unit and saving the use of water and electric power, in a vacuum cooling unit which cools to be cooled substance placed in a container to a low temperature using a steam compressor.例文帳に追加
蒸気圧縮機を使用して容器内に置かれた被冷却物を低温度に冷却する真空冷却装置において、従来のチラー装置のような比較的に大型の冷水製造装置を不要とし、且つ水や電気の使用量も抑え、安価な冷却コストで食品などを低温冷却することができる氷蓄熱式真空冷却装置を提供すること。 - 特許庁
To effectively utilize diffused heat and to improve heating promotion effect of the water stored in a hot water supply tank by applying a constitution to recover the heat of a radiator radiating heat of a refrigerant compressed by a compressor of an air conditioner to heat the water stored in the hot water supply tank of a hot water supply device in home and other facilities provided with the air conditioner and the hot water supply device.例文帳に追加
空気調和装置と給湯装置が設置された一般家庭やその他の施設において、空気調和装置の圧縮機で圧縮した冷媒の熱を放熱する放熱器の熱を回収して、給湯装置の給湯タンクに溜めた水を加熱する構成によって、放散される熱の有効利用を図ると共に、給湯タンクに溜めた水の加熱促進効果も図るものである。 - 特許庁
The compressor comprises: an impeller 3; a casing body 10 accommodating the impeller 3 and containing a flow passage R_1 formed to feed air to the impeller 3; and an atomizing unit 30 disposed upstream of the impeller 3 in the flow passage R_1 and spraying spray droplets in the air, of a grain size evaporable in an energizing region in which the impeller 3 imparts energy to the air.例文帳に追加
インペラ3と、インペラ3を収容するとともに、インペラ3に向けて空気を送気する流路R_1が形成されたケーシング本体10と、流路R_1のインペラ3よりも上流側に配置され且つインペラ3により空気にエネルギーを付与するエネルギー付与領域で蒸発可能な粒径の噴霧液滴を空気中に噴霧する噴霧装置30とを備える。 - 特許庁
Suction holes 10 are distributively provided on a table 5 along the paper sheets conveyance direction, a vacuum generator 11 is connected to each suction hole 10, a compressor 13 is connected via solenoid valves 12, and a plurality of overlapped paper sheets put in a paper sheets supply opening A is positively separated and conveyed by controlling ON/OFF of each solenoid valve 12 by a control part 14.例文帳に追加
テーブル5に、紙葉類搬送方向に沿って分布的に吸着ホール10を設け、各吸着ホール10に真空発生器11を連結するとともに、電磁弁12を介してコンプレッサ13を連結し、各電磁弁12を、制御部14でオン/オフ制御することによって、紙葉類投入口Aに投入された複数枚重なった紙葉類を確実に分離して搬送する。 - 特許庁
Operation devices 20, 25, 30, 35, 40 are provided with a determining means 55 for obtaining actual pressure ratio through the compressor from parameters measured using measuring means 25, 30 for diagnosis of compression, a comparison means 45 for comparing the actual measured pressure ratio with the previously given value, and an error detection means 50 for detecting error in accordance with the result of comparison.例文帳に追加
運転装置(20、25、30、35、40)は、圧縮の診断のために、測定手段(25、30)を用いて測定されたパラメータから、圧縮器を介して実際の圧力比を求める確定手段(55)と、測定された実際の圧力比を前もって与えられている値と比較する比較手段(45)と、前記比較の結果に応じて、エラーを検出するエラー検出手段(50)と、を備える。 - 特許庁
The refrigerating machine oil including the fine particles for sealing is injected in a mist state through a high-pressure injection pump 10 on the way of a high pressure-side refrigerant gas pipe from a compressor discharge side to a condenser inlet side of the refrigerant circulation passage at injecting the refrigerating machine oil including the fine particles for sealing to the refrigerant circulation passage of the refrigerating device such as the air conditioner.例文帳に追加
空気調和機等冷凍装置の冷媒循環経路内にシール用の微粒子を含んだ冷凍機油を注入するに際し、上記冷媒循環経路の圧縮機吐出側から凝縮器入口側までの高圧側冷媒ガス配管の途中に、高圧注入ポンプ10を介して上記シール用の微粒子を含んだ冷凍機油をミスト状態で注入するようにした。 - 特許庁
In the reciprocating compressor, a plurality of gas compressing sections having a cylinder and a piston are provided, and the piston movement in each gas compressing section is a coupled-movement, which is produced by transforming rotating movement of a crank shaft provided to a drive source into reciprocating movement via Scotch yoke mechanism.例文帳に追加
シリンダとピストンとからなるガス圧縮部が複数配設され、各ガス圧縮部のピストン運動は、駆動源に設けられたクランク軸の回転運動をスコッチヨーク機構により往復運動に変換して連動するようにした往復動圧縮機であって、第4のガス圧縮部4におけるヘッドシリンダ5の吐出口5aに、膨張型マフラ23を形成したディスチャージブロック21を止めボルト22により取り付ける。 - 特許庁
The control circuit 40 of this gas separator selects a pressure control system (P type operation) until a predetermined time t_1 when the freezing type air dryer 16 becomes a moisture removable state after starting is elapsed and selects an unload system (U type operation) subjecting the compressor 13 to load or unload operation when the predetermined time t_1 bringing the air dryer 16 to the moisture removable state is elapsed.例文帳に追加
気体分離装置の制御回路40は、冷凍式のエアドライヤ16が始動されてから除湿可能になる所定時間t_1が経過するまで圧力制御式(P式運転)を選択し、エアドライヤ16が除湿可能な状態になる所定時間t_1が経過したときコンプレッサ13をロード運転またはアンロード運転するアンロード式(U式運転)を選択する。 - 特許庁
The drying machine comprises a cooling unit (21) and a radiator unit (22) sequentially arranged in the air path with respect to the airflow, and a compressor (26) and a pressure reducer (27) for constituting a refrigerating cycle together with the cooling unit and the radiator unit, wherein the refrigerant of the refrigerating cycle is subjected to phase change in a supercritical region inside the radiator unit.例文帳に追加
そして、この乾燥機は、前記風路内に配置される冷却器(21)と、前記風路内でかつ、前記冷却器の風下側に配置される放熱器(22)と、前記冷却器および放熱器とともに冷凍サイクルを構成する圧縮機(26)および減圧装置(27)とを備えており、かつ、前記冷凍サイクルの冷媒は、放熱器内において超臨界域で状態変化する冷媒である。 - 特許庁
In a structure wherein an inverter 8 applies a driving voltage and a driving frequency to a motor 10 for a linear compressor 4, a power factor is calculated from a current flowing in and a voltage applied to the motor 10, a system load is detected from load state detecting means 14, and the driving frequency can be thus matched with a mechanical resonant frequency to provide an efficient and stable system.例文帳に追加
リニアコンプレッサー4のモーター10へ駆動電圧及び駆動周波数をインバータ8により印加する構成において、モーター10に流れる電流及び印加される電圧から力率を計算し、負荷状態検出手段14からシステム負荷量を検出することにより、駆動周波数と機械系の共振周波数を一致させて、高効率で安定したシステムが提供できる。 - 特許庁
The cooling system 50 forcibly circulates a cooling material, and is provided with: a first circulation passage 54 equipped with a radiator 52 for radiating heat; a second circulation passage 60 equipped with a compressor 64 and an expansion valve 66; and first through fourth four-way valves 62a-62d for selecting circulation passages to be opened between the circulation passages 54 and 60.例文帳に追加
第2の強制循環冷却系50は、冷却材を強制循環させるとともに、熱を放出するためのラジエータ52を備える第1の循環路54と、圧縮器64、膨張弁66を備える第2の循環路60と、前記第1と第2の循環路54,60の間で、開状態となる循環路を切り換える第1ないし第4の4方弁62a〜62dを備える。 - 特許庁
A cushioning material 70 is provided between a first casing 60A housing a compressor 20 and a motor 30 which are connected to an engine via an intake pipe 50 and a second casing 60B housing an inverter device 40, and absorbs relative displacement of the first casing 60A to which vibration of the engine side is transmitted and the second casing 60B to which vibration of the vehicle body side is transmitted.例文帳に追加
インテークパイプ50を介してエンジンに接続されたコンプレッサ20および電動機30を収容した第一ケーシング60Aと、インバータ装置40を収容した第二ケーシング60Bとの間に、緩衝材70を設け、エンジン側の振動が伝達される第一ケーシング60Aと、車体側の振動が伝達される第二ケーシング60Bとの相対変位を吸収する。 - 特許庁
Air sucked by a compressor body 9 for compressing circulates through a motor housing 8, and a crankcase 10, the air intake passage 26 is constituted such that air flowing into the crankcase 10 from an air inlet 17 is circulated around each brush 7 and is cooled and thereafter is passed a gap between the rotor 4 and the stator 5 and is flown so as to cool the same.例文帳に追加
圧縮機本体9が圧縮するために吸込む空気は、モータハウジング8、クランクケース10内を流通させ、この吸気流路26としては、吸気口17からクランクケース10内に流入する空気を、各ブラシ7の周囲で流通させて冷却した後に、ロータ4とステータ5との隙間を通してこれらを冷却するように流す構成としている。 - 特許庁
A control device 53 memorizes the peak value of carbon emission spectrum as the initial value, and when the initial value increases, the control device sends instruction to each fluid supply system so that the air from a compressor 19 may be supplied into the torch 1 or the hydrogen from a hydrogen bomb 20 may be supplied into the torch 1 or the supply rate of the steam may be increased or these supply may be executed in combination.例文帳に追加
制御装置53は炭素発光スペクトルのピーク値を初期値として記憶し、初期値が増加する場合には、コンプレッサー19からのエアーをトーチ1内に供給させるか、水素ボンベ20からの水素をトーチ1内に供給させるか、水蒸気の供給量を増加させるか、或いはこれら供給を複合して行うように各流体供給系に指令を送る。 - 特許庁
The control device of the internal combustion engine comprises the turbocharger 11 disposed incidentally to the internal combustion engine 1, the motor 11b capable of generating power by rotating a turbine/compressor 11a of the turbocharger 11 with exhaust flow, and an output increasing means for increasing the output of the internal combustion engine 1 during power generation by the motor 11b.例文帳に追加
本発明の内燃機関の制御装置は、内燃機関1に付随して配設されたターボチャージャ11と、排気流によって該ターボチャージャ11のタービン/コンプレッサ11aを回転させて発電を行い得る電動機11bと、電動機11bによる発電時に、内燃機関1の出力を増大させる出力増大手段とを備えていることを特徴としている。 - 特許庁
To provide a sealed compressor capable of discharging gas separating gas from liquid sufficiently by restraining substantially refrigerant and oil and handling them because flow of refrigerant gas and oil cannot be completely restrained and their collision and turning are insufficient and mixing of oil into refrigerant gas discharged to the outside of a sealed vessel cannot be completely prevented in a conventional system.例文帳に追加
従来の方式は冷媒ガスやオイルの流れを拘束し切れず衝突や旋回が不十分であったりして、密閉容器外に吐出する冷媒ガスにオイルが混入することを防止しきれておらず、本発明の目的は冷媒およびオイルをほぼ拘束して取扱って、十分に気液分離されたガスを吐出することができる密閉型圧縮機を提供することにある。 - 特許庁
In a defrosting process, even when liquid refrigerant is collected due to abrupt cooling of the evaporation tray pipe 22 by defrosting water and all the refrigerants become liquid refrigerant and overflow from the evaporation tray pipe 22, liquid refrigerant is collected in the rising part 25, the spiral condenser 12, and the cooler 15 to surely prevent liquid refrigerant from returning to the discharge port 11A side of the compressor 11.例文帳に追加
除霜工程において、除霜水により蒸発皿パイプ22が急激に冷却されることに起因して液冷媒が集まり、仮に全ての冷媒が液冷媒となって蒸発皿パイプ22から溢れたとしても、立ち上がり部25、スパイラルコンデンサ12さらには冷却器15にわたって溜められて、圧縮機11の吐出口11A側に液冷媒が戻ることが確実に防がれる。 - 特許庁
An air compressor is provided with a compressed air generating means generating compressed air, a tank part storing compressed air generated by the compressed air generating means, the motor means for driving the compressed air generating means, control means 5 and 20 controlling a driving amount of the motor means and a current detecting means 28 detecting a driving current value used for driving the motor means.例文帳に追加
エアコンプレッサは、圧縮空気を生成する圧縮空気生成手段と、圧縮空気生成手段により生成された圧縮空気を貯留するタンク部と、圧縮空気生成手段を駆動させるためのモータ手段と、モータ手段の駆動量を制御する制御手段5、20と、モータ手段の駆動に用いられる駆動電流値を検出する電流検出手段28とを有している。 - 特許庁
An air pump comprises a transformer 2 to which an alternating current is fed; a permanent magnet 3 situated opposite to the core 2a of the transformer 2; a lever 5 integrally mounted on the permanent magnet 3; a diaphragm 4 to compress and expand air according to displacement of the lever 5; and an air compressor chamber 4a to straighten a flow of air against compression and expansion of the diaphragm 4.例文帳に追加
エアーポンプは、交流電流の供給されるトランスフォーマ2と、トランスフォーマ2のコア2aに対向して設けられた永久磁石3と、永久磁石3が一体に取付けられたレバー5と、レバー5の変位に応じて空気を圧縮伸張させるダイヤフラム4と、ダイヤフラム4の圧縮伸張に対して空気の流れを整流する空気圧縮室4aとを備えている。 - 特許庁
To reduce the noise of a centrifugal machine by actively reducing sound power emitted by a noise source with respect to low frequency noise which cannot be reduced by means of a passive silencer such as a sound absorbing material in the active noise reduction controller of the centrifugal machine which reduces the sound level of noise sources such as a compressor in the refrigerating cycle of the centrifugal machine, a motor, or a fan.例文帳に追加
本発明は、遠心機の冷凍サイクルのコンプレッサ又はモータ又はファン等の騒音源の音響レベルを低減する遠心機の能動消音制御装置に関するものであり、吸音材等による受動消音器で低減できない低周波騒音に対し、騒音源が射出する音響パワーを能動的に減少させ、遠心機の騒音を低減することである。 - 特許庁
In order to reduce the accumulated SO_x quantity in the NO_x catalyst 22 when stopping the fuel supply in an engine decelerating operation, the secondary air control valve 33 is opened while temporarily holding the average air-fuel ratio of the exhaust gas carried into the NO_x catalyst 22 in a rich state to supply the air discharged from the compressor 15 to the auxiliary catalyst 23 through the secondary air passage 31.例文帳に追加
機関減速運転時の燃料供給停止時に、NO_X触媒22内の蓄積SO_X量を減少させるために、NO_X触媒22内に流入する排気ガスの平均空燃比を一時的にリッチに保持しながら、二次空気制御弁33を開弁してコンプレッサ15から吐出された空気を補助触媒23に二次空気通路31を介して供給する。 - 特許庁
Thus, the compressor having high reliability that can secure a stable shaft force with a small fastening torque to suppress the core shift between the cylinder 104 and the main shaft end plate 107 due to a load for pressing the cylinder 104 at a time of press fitting or brazing of a connecting pipe 106 and suppresses the distortion of the cylinder inner wall due to the fastening of the bolt 19a.例文帳に追加
これによって、小さい絞め付けトルクで安定した軸力を確保でき接続管106の圧入時やロ−付け時にシリンダ104を押す荷重によるシリンダ104と主軸端板107の芯ずれを抑制するとともに、ボルト19aの締結によるシリンダ気筒内壁の歪を抑制し信頼性の高い圧縮機を提供することができるものである。 - 特許庁
In method for positioning and fixing the rotation preventive mechanism/thrust bearing member of a movable spiral body in a scroll compressor for refrigerating air conditioner, the movable spiral body and plate ad/or front housing and plate are relatively positioned and fixed by providing a projection 5 on the plate 1 of a rotation preventive member 50 by drawing and press- fitting the projection 5 into the mate member.例文帳に追加
冷凍空調用のスクロール式圧縮機における可動渦巻体の回転阻止機構/スラスト軸受部材の位置決め及び固定方法において、前記回転阻止部材50のプレート1,2にプレス絞りにて、凸部5を設け、相手部材にその凸部を圧入することで、可動渦巻体とプレート及び/又はフロントハウジングとプレートの相対的な位置決めと固定を行う。 - 特許庁
When the calculation result is within a range of the set data quantity, a surface sequence compressor 12 executes a compression process with a point-surface transformation, but if it lies outside the range of the set data quantity, the calculator 13 recalculates the data quantity after changing compression parameters, thereby avoiding unnecessary point-surface or surface-point transformations.例文帳に追加
そして、算出結果が設定データ量の範囲内であれば、面順次圧縮部12が点面変換を伴う圧縮処理を行う一方、算出結果が設定データ量の範囲内になければ、圧縮パラメータを変更して前記面データサイズ算出部13によるデータ量の再算出を行うようにし、不必要な点面変換や面点変換を行わないようにする。 - 特許庁
A fixed base 28 for collecting and holding dew condensation water attached to the compressor 26 or a connection pipe 52 that comprise the heat pump device is placed above or below the lowest end 35 of a water pan 31 installed below an evaporator 49 to lead the dew condensation water collected on the fixed base 28 to a drainage 54 by natural draining by the difference in height and achieve stable draining process.例文帳に追加
ヒートポンプ装置を構成する圧縮機26や接続パイプ52に付着した結露水を収集保持する固定基盤28を、蒸発器49の下部に設けた水受け皿31の最下端35より上部または下部に位置させ、固定基盤28に収集した結露水を高低差による自然排水で排水路54に導き、排水処理を安定して行えるようにする。 - 特許庁
To control refrigeration facility in accordance with an increase in the load of a refrigerating chamber without remarkably reducing the temperature thereof in the case where the load of the freezing chamber alone increases when the ambient temperature is low and the load is small in a two-stage refrigerant compressor type freezer having a plurality of evaporators different in evaporating temperature as typified by a freezer-refrigerator and the like.例文帳に追加
冷凍冷蔵庫等に代表される蒸発温度の異なる複数の蒸発器を有する冷媒二段圧縮式冷凍装置において、外気温が低く負荷が小さい時に冷凍室の負荷だけが増大した場合に、冷蔵室温度を著しく低下させることなく、冷凍室の負荷の増大に対応した冷凍能力制御を行うことを目的とする。 - 特許庁
This two-stage compressor, in which a first compression section 120 for compressing the refrigerant in a refrigerating cycle and a second compression section 130 for further compressing the refrigerant compressed by the first compression section 120 are stored in a container 110, is provided with a lubricating oil separator 180 for separating lubricating oil contained in the refrigerant on the discharge side of the second compression section 130.例文帳に追加
冷凍サイクル中の冷媒を圧縮する第1圧縮部120と、第1圧縮部120で圧縮された冷媒を更に圧縮する第2圧縮部130とが容器110内に収容されて成る2段圧縮機において、第2圧縮部130の吐出側に冷媒中に含まれる潤滑油を分離する潤滑油分離器180を設ける。 - 特許庁
This variable amount regulating device for the variable radius type scroll compressor comprises a rotary shaft 100 connected with the slewing scroll 3 for transmitting a rotary force of a driving motor, and an eccentric bushing 200 connected with a driving pin portion 110 of the rotary shaft 100 for transmitting the rotary force of the driving motor to the revolving scroll 3 and limiting the retreat amount of the slewing scroll 3.例文帳に追加
可変半径式スクロール圧縮機の可変量調節装置が、旋回スクロール3に結合されて駆動モータの回転力を伝達する回転軸100と、該回転軸100の駆動ピン部110に結合されて駆動モータの回転力を前記旋回スクロール3に伝達すると同時に、該旋回スクロール3の後退量を制限する偏心ブッシング200とを具備する。 - 特許庁
To prevent generation of knocking by supplying cooling exhaust gas for EGR to a main chamber and to reduce compressor load by providing a supply system for mixing a part of gas full with cooling exhaust gas in an intake stroke, feeding compressed air, promoting their mixing, and supplying cooling exhaust gas to the main chamber in addition to a supply system for supplying compressed air to the main chamber, in a gas engine.例文帳に追加
このガスエンジンは,EGR用冷却排気ガスを主室に供給してノッキングの発生を防止し,吸入行程でガス燃料の一部と冷却排気ガスを先ず混合し,次いで圧縮空気を送り込んで混合を促進し,冷却排気ガスを主室へ供給する供給系を圧縮空気の主室への供給系と別に設けてコンプレッサ仕事を低減する。 - 特許庁
The vapor compression type refrigeration circuit is provided with the compound compressor 14 having a low stage compression part 34 and a high stage compression part 36 connected in series, and the intercooler 32 put in a refrigerant channel connecting between the low stage compression part 34 and the high stage compression part 36 and sucking refrigerant into the high stage compression part 36 after cooling the refrigerant discharged from the low stage compression part 34.例文帳に追加
蒸気圧縮式冷凍回路は、互いに直列に接続される低段圧縮部34及び高段圧縮部36を有するコンパウンド圧縮機14と、低段圧縮部34と高段圧縮部36との間を繋ぐ冷媒の流路に介挿され、低段圧縮部34から吐出された冷媒を冷却してから高段圧縮部36に吸入させる中間冷却器32とを備える。 - 特許庁
In the machine chamber formed under a showcase body which is installed with the refrigeration device including a condenser and a compressor, an electric component box, and a condensate water receiver, a metal or synthetic resin heat resisting tube 12 is arranged between radiator plates 10 of a control device of the electric component box in a meandering manner, and liquid as a refrigerant is carried to the heat resisting tube 12.例文帳に追加
内部に凝縮器や圧縮機などにより構成される冷凍装置や、電装ボックスや、ドレン水受けを設置したショーケース本体の下部に形成される機械室において、電装ボックスの制御装置の放熱板10間に金属製または合成樹脂製の耐熱チューブ12を蛇行させて配設し、この耐熱チューブ12に冷媒としての液体を流す。 - 特許庁
The system can also include a reintroducing manifold (19) for receiving combustor bypass air extracted from the compressor delivery air in the annular passage (13) and one or a plurality of reintroducing slots (21) communicating with the reintroducing manifold (19) so as to inject the combustor bypass air into the combustor body (11) on the downstream side of the reaction area (15).例文帳に追加
当該システムはさらに、環状通路(13)内の圧縮機吐出空気から抽出された燃焼器バイパス空気を受け入れるための再導入マニホルド(19)と、反応域(15)の下流で燃焼器バイパス空気を燃焼器本体(11)に注入するように再導入マニホルド(19)と連通する1つまたは複数の再導入スロット(21)とを含むことができる。 - 特許庁
The refrigerating apparatus is constituted to carry out individual defrosting operation of supplying a part of a discharge refrigerant of a high stage side compressor 31 to the utilization side heat exchanger 51 for defrosting after a simultaneous defrosting operation and at the same time, performing refrigerant discharge operation of supplying the refrigerant accumulated in the utilization side circuit corresponding to the other utilization side heat exchanger, to the utilization side heat exchanger to be defrosted.例文帳に追加
冷凍装置は、同時デフロスト運転後には、高段側圧縮機の吐出冷媒を一部の利用側熱交換器へ送って除霜すると同時に、他の利用側熱交換器に対応する利用側回路に溜まった冷媒を除霜対象の利用側熱交換器へ送る冷媒排出動作を行う個別デフロスト運転を実行可能に構成されている。 - 特許庁
To provide a lubricating oil supply apparatus of a reciprocating compressor which enhances a lubricating performance, by reducing a dead volume existing at an oil supply apparatus and thus by smoothly supplying lubricating oil even at the time of an initial driving that requires less pumping amount, and enhances an assembly characteristic and reducing a fabrication cost, by simplifying a structure of a pumping unit for pumping lubricating oil.例文帳に追加
潤滑油供給装置に存在する無駄容積を減らして、圧送量の少ない初期起動時にも潤滑油を円滑に供給させることで、潤滑性能を向上し得ると共に、潤滑油を圧送するポンピングユニットの構造を単純化することで、組立性を向上し、且つ製造原価を節減し得る往復動式圧縮機の潤滑油供給装置を提供する。 - 特許庁
In this air conditioner composed of the outdoor machine having a compressor, an outdoor heat exchanger, and an outdoor fan and the indoor machine having an indoor heat exchanger and an indoor fan, dew condensation water generated by the indoor heat exchanger is led into the outdoor machine by a drain pipe to reduce temperature of air exhausted to the outdoor side from the outdoor fan by dew condensation water.例文帳に追加
圧縮機と室外熱交換器及び室外ファンを有する室外機と、室内熱交換器び室内ファンを有する室内機とで構成される空調機器において、前記室内熱交換器によって生成される結露水をドレン管で室外機に導き、該結露水によって室外ファンから屋外に排気される空気の温度を冷やすことを特徴とする。 - 特許庁
In the compressor equipped with the cylinder bore, a piston reciprocatably fitted in the cylinder bore, and the sealing piston ring disposed on an outer peripheral surface of the piston, a center position of an installation region of the same direction piston ring is on the bottom dead center side than the center position of a reciprocating direction fitting length of circumferential parts in the bottom dead center position.例文帳に追加
シリンダボアと、シリンダボア内に往復動可能に嵌合されたピストンと、ピストンの外周面に設けられたシール用のピストンリングとを有する圧縮機において、前記ピストンリングを、下死点位置における円周部同士の往復動方向嵌合長の中心位置よりも、同方向ピストンリングの設置領域の中心位置が下死点側にあることを特徴とする圧縮機。 - 特許庁
This system comprises: a washing device capable of spraying an atomized water to the gas turbine engine to release deposits from at least one compressor blade; and at least one water jetting device capable of jetting the atomized water to the air flow in the suction duct of the gas turbine engine or to the gas turbine under the control of a numerical hydrodynamics model for increasing the mass flow of the air flow.例文帳に追加
システムは、ガスタービンエンジンに霧状水を噴射でき、これにより少なくとも1つのコンプレッサブレードから付着物を解放する洗浄装置と、空気流の質量流量を増加するべく数値流体力学モデルの制御の下、ガスタービンエンジンの吸気ダクトの空気流か、又はガスタービンに霧状水を噴射可能な少なくとも1つの水噴射装置とを有する。 - 特許庁
This control valve CV comprises a first valve structure comprising a first valve element part 46, a pressure sensitive member 48 and an electromagnetic actuator 51, and a second valve structure comprising a valve element part 69 for opening and closing the delivery passages 67, 65, 49, 66 and 68 of the variable displacement compressor.例文帳に追加
制御弁CVは、容量可変型斜板式圧縮機のクランク室12の圧力変更につながる弁開度調節を行うための、第1弁体部46、感圧部材48及び電磁アクチュエータ51等からなる第1の弁構成と、容量可変型圧縮機の吐出通路67,65,49,66,68を開閉するための、第2弁体部69等からなる第2の弁構成を備えている。 - 特許庁
To compose a circuit minimizing power recovery loss while matching flow rate to work by using an expansion machine of a simple structure type although a complicated expansion ratio control means is required since an expansion machine requiring valve opening/closing control such as a reciprocating type is used coaxially with a compressor in the past, in a supercritical cycle refrigerating air conditioning device.例文帳に追加
超臨界サイクルの冷凍空調装置において、従来はレシプロ式のような弁開閉の制御が必要な膨張機を圧縮機と同軸で用いていたので、複雑な膨張比制御手段が必要であったが、機構が簡素な形式の膨張機を用いるために流量と仕事をマッチングさせながら動力回収ロスが極力小さくなるような回路を構成する。 - 特許庁
A hermetic compressor capable of providing high input reduction effect without generating viscous resistance is constructed since discharge of oil 103 into a hermetic vessel 101 is improved by positioning a lower end position of a ball part of the thrust ball bearing 131 lower than a lower end of the rotor 113 and oil is prevented from accumulating around the thrust ball bearing 131.例文帳に追加
スラストボールベアリング131のボール部の下端位置を回転子113下端より下に位置させることでオイル103の密閉容器101内への排出を良くし、スラストボールベアリング131周辺にオイル103が滞留することを防いだため、粘性抵抗が生じず、高い入力低減効果を得ることができる密閉型圧縮機を提供できるものである。 - 特許庁
The control ECU 74 drives the air compressor 52 and supplies the air with a volume exceeding the necessity, and controls the volume of the air for combustion by synchronizing with the fluctuation of the volume of the off-gas released from a PAS device 26, by controlling pressure control valves 57, 58 while maintaining the pressure of the air for reformation to be supplied to the reformation device 18.例文帳に追加
制御ECU74は、空気コンプレッサ52を駆動して必要空気量以上の空気を供給するとともに、圧力調整弁57、58及び供給圧制御レギュレータ59を制御して、改質装置18に供給される改質用空気の供給圧を一定に維持しつつ、PSA装置26からのオフガス放出量の変動に同期して、燃焼用空気量を変動させる。 - 特許庁
In the defrosting operation in an overload condition during a heater operation of this air conditioner, since a pressure difference can be reduced by fully opening an expansion valve 4 for a certain period before switching the four-way valve, the four-way valve 2 can be switched without stopping the compressor 1, whereby the defrosting time can be reduced and an optimum space can always be provided.例文帳に追加
空気調和機の暖房運転中の過負荷条件での除霜運転においては、四方弁切換え前に膨張弁を一定時間全開にすることにより、圧力差を小さくすることができるため、圧縮機を停止させることなく四方弁を切換えることができるので、除霜時間を短縮させることができ、常に最適空間を提供することができる。 - 特許庁
The rotary compressor used for a refrigeration cycle apparatus of the embodiment includes: a cylinder forming a cylinder chamber; a roller eccentrically rotatably contained in the cylinder chamber; a blade slidably set in a blade groove formed in the cylinder with a tip part abutting on an outer circumference of the roller; and a side plate provided at an end face of the cylinder and blocking the cylinder chamber.例文帳に追加
実施形態の冷凍サイクル装置に用いられる回転式圧縮装置は、シリンダ室を形成するシリンダと、前記シリンダ室内に偏心回転自在に収容されたローラと、前記シリンダに形成されたブレード溝に摺動可能に設けられ、先端部が前記ローラの外周面に当接するブレードと、シリンダの端面に設けられた前記シリンダ室を塞ぐ側板と、を備える。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|