| 意味 | 例文 |
lead toの部分一致の例文一覧と使い方
該当件数 : 20631件
To provide a digital phase locked loop(PLL) circuit that causes no hazard to an output clock of the PLL when a delay output lead-out position of unit delay elements in multi-stage connection is changed.例文帳に追加
デジタルPLL回路において、多段接続された単位遅延素子の遅延出力引き出し位置を変更する時にPLL出力クロックにハザードが発生しないようにする。 - 特許庁
This lead-free solder for high-low temperature used for a printed circuit board using in a test burn-in test has a composition containing, by weight, 3 to 3.5% Ag and 0.3 to 0.5% Cu, and the balance Sn.例文帳に追加
テスト・バーン・イン試験で用いるプリント基板に使用する高低温用無鉛はんだを、Agを3〜3.5[重量%]、Cuを0.3〜0.5[重量%]、残りをSnとして組成する。 - 特許庁
Then, the high hydrophilic sheet 4 is inserted into the battery case 5 at the state, so that it is made to make contact with the surface of negative electrode plate 2 which lies outside of electrode plate groups, to manufacture the sealed type lead-acid battery.例文帳に追加
そして、該高吸水性シート4を、極板群外側の負極板2の表面に接触させた状態で電槽5に挿入して密閉形鉛蓄電池を作製する。 - 特許庁
The switch (20) is a lead switch (20) which is designed to operate with gravity and arranged on a printed circuit board (8) connecting to a control system of the driving motor (3).例文帳に追加
前記スイッチ(20)は、重力により作動するように設計され、かつ前記駆動モータ(3)の制御システムに接続されたプリント回路基板(8)上に配置されるリードスイッチ(20)である。 - 特許庁
To provide a lead-free low melting-point glass which is prevented from yellowing due to silver reaction and has high visible light transmittance aiming at the development of the more excellent electronic material substrate represented by a plasma display panel.例文帳に追加
プラズマディスプレイパネルに代表される電子材料基板開発で、銀反応による黄変が抑制され、かつ可視光透過率の高い無鉛低融点ガラスが望まれている。 - 特許庁
Keeping the density of an active substance for the positive electrode after making a battery jar to be 3.5 to 4.4 g/ml, the lead battery with the control valve in which the pressure for a group of the electrode plates is 20 kPa or higher, is assembled.例文帳に追加
そして、電槽化成後の正極活物質の密度を3.5〜4.4g/mlにし、極板群の加圧力が20kPa以上の制御弁式鉛蓄電池を組み立てる。 - 特許庁
The first housing 24 is connected to the second one 26, thus connecting the electric-wire-side lead 50 of the communication control IC 30 to a female terminal 62 of the busbar connection element 34.例文帳に追加
第一と第二のハウジング24と26を結合することで、通信制御IC30の電線側リード50がバスバー接続子34の雌端子62に接続されるようになっている。 - 特許庁
To provide a high-frequency package capable of preventing degradation of a high-frequency characteristic due to a stub structure, while fully securing the brazing strength of a lead terminal of a high-frequency package.例文帳に追加
高周波パッケージのリード端子のろう付け強度を十分に確保しつつ、スタブ構造に起因する高周波特性の劣化を防止可能な高周波パッケージを提供する。 - 特許庁
Then the kneaded matter after left standing, is stirred to prepare the paste active material for the positive electrode containing 67% or more tetrabasic lead sulfate of 5-50 μm to be used in a positive plate.例文帳に追加
そして、放置後の前記混練物を攪拌し、5〜50μmの四塩基性硫酸鉛が67%以上存在させた正極用ペースト状活物質を製造して正極板に使用する。 - 特許庁
To enable a connecting part by an inner lead line to be fully sealed by using one kind of a sealant without manufacturing processes and the head structure being complicated in manufacturing of a recording head.例文帳に追加
記録ヘッドの製造において、製造工程やヘッド構造を複雑化することなく、1種類の封止剤を用いてインナーリード線による接続部を十分に封止することを可能とする。 - 特許庁
To reduce wiring defects of a lead-out wire below a seal area while precisely controlling a gap by putting a gap material in the seal area with respect to a matrix drive type electrooptic device.例文帳に追加
マトリクス駆動方式の電気光学装置において、シール領域にギャップ材を入れてギャップを精度良く制御しつつ、シール領域下の引き出し配線の配線不良を低減する。 - 特許庁
This planar lighting device comprises a nearly transparent light guide plate 11 constructed so as to lead emitted light from the point light source 12 to the lighted body side from the outgoing face 11a.例文帳に追加
点光源12からの出射光を出射面11aから被照明体側に導くように構成されたほぼ透明な導光板11を備える面状照明装置である。 - 特許庁
To obtain a sheet setting device for prepreparation of sealing which can enhance the productivity and the quality of optical-to-electrical transducer module in which sides on one side of a pair of lead wires are used as output power wires.例文帳に追加
一対のリード線の一端側を出力取出し線として用いる光電変換モジュールの生産性及び品質を向上できる封止前準備用シートセット装置を得る。 - 特許庁
Thus, the sink is prepared with solid lead and is made movable so that the same effect may be obtained as the sink is pulled to the direction completely opposite to the snagging one.例文帳に追加
釣具錘は、連結されたハリ仕掛けと介する道糸が引かれると、その引張方向に対して面する該錘の部分が、障害物に接触して根掛かりになる場合が多い。 - 特許庁
To provide a proximity switch with the use of a case which can be easily manufactured without adding stress to and damaging a glass tube or generating burrs on a lead terminal.例文帳に追加
ガラス管にストレスが加わり損傷させることがなく、リード端子にバリが発生するようなことがなく、容易に製作することが可能なケースを用いた近接スイッチを提供する。 - 特許庁
To suppress the adverse influence on a piezoelectric element due to heat generation of a laser diode by suppressing the adverse influence of a lead line against the rotation of a head slider caused by an extension and contraction operation of the piezoelectric element.例文帳に追加
ピエゾ素子の伸縮動作によるヘッド・スライダの回動に対するリード線の悪影響を抑制し、レーザーダイオードの発熱によるピエゾ素子への悪影響も抑制する。 - 特許庁
To provide a soldering material provided with an excellent characteristics as the soldering material with respect to wettability, fluidity, fillet exfoliation, copper solubility rate, impurity content, etc., and substantially not containing lead.例文帳に追加
ぬれ性、流動性、隅肉剥離、銅溶解率、不純物成分等の点において、はんだ材としてのすぐれた特性を具えた、実質的に鉛無含有のはんだ材を提供すること。 - 特許庁
To utilize a signal side lead member as it is even when an effective element pattern in a vibrating part is changed in the case of manufacturing an ultrasonic vibrator to which the sparse method is applied.例文帳に追加
スパース法が適用された超音波振動子を製造する場合において、振動部おける有効素子パターンの変更があってもシグナル側リード部材をそのまま利用できるようにする。 - 特許庁
To suppress occurrence of defective soldering by forming lead wires for a cylindrical piezoelectric vibrator so as to stabilize the mount of the cylindrical piezoelectric vibrator compatible with a simple surface mount onto a printed circuit board.例文帳に追加
円筒型圧電振動子のリード線を成形し簡易表面実装対応化した円筒型圧電振動子の回路基板への実装を安定化し、ハンダ付けの不具合発生を抑さえる。 - 特許庁
The feeder 11 further comprises means for carrying the lead terminal 1 to a fixing position while directing it in a direction orthogonal to a stripe electrode foil extending in the horizontal direction.例文帳に追加
また、供給装置11は、リード端子1を、水平方向に延びる帯状の電極箔に対し直交方向を向いた状態で、取着位置にまで搬送する搬送手段を備える。 - 特許庁
The cross sectional area of the bent part is desirably to be the range of 50 to 80% of the cross sectional area of the main part from the balance of the prevention of the occurrence of the remaining stress and lead strength.例文帳に追加
このとき残留応力の発生防止とリード強度とのバランスから、前記折り曲げ部分の断面積は主たる部分の断面積の50〜80%の範囲であるのがよい。 - 特許庁
To provide a system for controlling the circulation of an image forming device capable of shortening a lead time from order reception to delivery, reducing an inventory value, shortening the term of delivery, and reducing costs.例文帳に追加
受注から納入までのリードタイムを短縮するとともに, 在庫量の低減を図り短納期、低価格化を図ることができる画像形成装置の流通管理システムを提供する。 - 特許庁
The case 2 for an electronic component mounting board allows an electronic component to be mounted on the board while lead terminals are inserted into the guide holes 8a and connected to the socket after the board is housed.例文帳に追加
この電子部品搭載基板用ケース2においては、基板を収めた後、ガイド孔8aにリード端子をソケットに接続しながら電子部品を基板に搭載することができる。 - 特許庁
A conductive member adjacent to the sheathing surface of the sheathing resin is mounted on the surface of the peripheral side face of a reverse-end face as a whole, to the anode lead on the surface of the cathode current collector.例文帳に追加
本発明は、陰極集電体の表面の陽極用リードとは反対端面の周辺側面全面部分に外装樹脂の外装表面に近接する導電部材を設ける。 - 特許庁
To provide a probe sensing structure of a BNC connector by which, a probe sensing function can be added to an existing BNC connector afterwards, and the draw-out position of lead-out parts of a sensor ring can be freely changed.例文帳に追加
既存のBNCコネクタに対して後からプローブセンス機能を付加でき、しかもセンサリングのリードアウト部の導出位置の変更も自由なBNCコネクタのプローブセンス構造を得るにある。 - 特許庁
To provide an air conditioner for securing the reliability of electric connection by reducing repetitive stress which is generated in a lead wire introduced from an electric component to the side of an indoor unit body.例文帳に追加
電装品から室内機本体側へ導かれるリード線に発生する繰返し応力を低減して、電気的接続の信頼性を確保する空気調和機を提供する。 - 特許庁
In the semiconductor device, an annular groove 13 is formed in a joint surface 12 to which an IC element 20 is solder-jointed, of a lead frame 11 so as to prevent a solder 30 applied inward from outflowing outward.例文帳に追加
IC素子20がはんだ接合されるリードフレーム11の接合面12には、内方に塗布されたはんだ30の外方への流出を防止する環状溝13が形成されている。 - 特許庁
The laminated structure and the ring structure are connected to each other by at least one of the plurality of first wiring layers, and the lead-out wiring is connected to the ring structure.例文帳に追加
積層構造体とリング構造体とは複数の第1配線層の少なくとも1つによって互いに接続されており、引き出し配線はリング構造体と接続されている。 - 特許庁
The solder material is coated by jetting and applying to a lead terminal 11 of the electronic parts with a solder from a solder supplying device 14 from a second direction crossed at substantially the right angle to the first direction.例文帳に追加
第1の方向に実質的に直交する第2の方向から、ハンダ供給装置14によりハンダ材を電子部品のリード端子11に対し噴射して塗布する。 - 特許庁
To provide a soldering method which solves the soldering failure due to excessive fused solder upon soldering while applying internal pressure inside through-holes in a lead component mounting substrate.例文帳に追加
リード部品搭載基板のスルーホール内に内圧をかけながらはんだ付けをする場合の過剰の溶融はんだによるはんだ付け不良を解決できるはんだ付け方法を提供する。 - 特許庁
To provide a secondary battery for substantially and uniformly deriving currents generated at each section of an electrode group and enhancing a collecting efficiency by a lead to improve output performance.例文帳に追加
電極群の各部位で発生した電流を実質的に均一に引き出し、リードによる集電効率を高めて出力性能を向上させることができる二次電池を提供する。 - 特許庁
The wiring route from each device to the lead wire holding part 22 is bound without unnecessarily loosening, whereby the wiring position can be stabilized to prevent the wires from being moved around or entangled.例文帳に追加
各ディバイスからリード線保持部22までの配線経路を不必要に弛ませないで結束することで、配線位置が安定しあちこちと移動したり絡み合ったりするのを防止できる。 - 特許庁
A correcting lead 6 to be connected serially to a horizontal deflection coil 1 is arranged at the outer peripheral position of the coil 1 and between the coil 1 and the displaying surface of CRT 4.例文帳に追加
水平偏向コイル1の外周位置および水平偏向コイル1とCRT4の表示面との間に、水平偏向コイル1に直列に接続される補正リード6を配置する。 - 特許庁
The optical pickup 11 is so formed as to be further moved to a -X side from a position at which a lead-in switch 25 is turned on and a cleaning switch 26 is provided at a moving end of the optical pickup.例文帳に追加
光ピックアップ11は、リードインスイッチ25がオンとなる位置よりも、さらに−X側に移動できるようになっており、その移動端に、クリーニングスイッチ26が設けられている。 - 特許庁
The coil ends of the divided cores 18a are mutually connected for each phase via a first to third connection lead wires 12, 14, 16 corresponding to axially arranged U, V, W phases.例文帳に追加
分割コア18aのコイル端部は、軸方向に配列されたU、V、W相に対応する第1〜第3接続導線12、14、16を介して各相毎に相互接続される。 - 特許庁
A fixed rotary transformer 21b is fitted to a roller support base 20 by bolts, which are not illustrated, and the fixed rotary transformer 21b is connected to an ultrasonic oscillator, which is not illustrated, through a lead wire.例文帳に追加
ローラ支持台20には固定側のロータリートランス21bが図示しないボルトにより取付けられ、固定側のロータリートランスは図示しない超音波発振器とリード線により接続されている。 - 特許庁
Making common the SCV driving circuit and pressure reducing valve driving circuit of conventional type allows simplifying the constitution of the output circuit of the ECU to lead to cost-down of the ECU.例文帳に追加
また、従来のSCV駆動回路と減圧弁駆動回路を共通化することで、ECUの出力回路の構成を簡略化でき、ECUのコストダウンを図ることができる。 - 特許庁
An oil passage 50 to lead hydraulic oil leaked to the pressure relief hole 38 into the engine cover A is formed on the surface of the flange 12 on which the engine cover A abuts and the periphery of the housing 11.例文帳に追加
フランジ12のエンジンカバーAに対する衝合面およびハウジング11の外周に圧力逃がし孔38に漏洩した作動油をエンジンカバーA内に導く油路50を形成する。 - 特許庁
The sheet 40 is provided with a recess 40a, in order to lead out the end part of the optical fiber cable F contained in the lower case 11 and to connect a connector C with the receptacle 31e of the main case 30.例文帳に追加
シート40には窪部40aを設けてロアケース11に収納された光ファイバーケーブルFの端部を引き出してコネクタCをメインケース30のレセプタクル31eに接続する。 - 特許庁
Seen along a pinching direction Z1 of the pair of elastic piece parts 30, the direction to which the elastic piece parts 30 are extended is in parallel with an axial length direction X1 to which the outer lead 13 is extended.例文帳に追加
一対の弾性片部30の挟持方向Z1に沿って見たときに、弾性片部30が延びる方向とアウターリード13の延びる軸長方向X1とが平行である。 - 特許庁
To provide a method for stably producing a crude zinc oxide-lead sintered lump hard to be softened or melted in a blast furnace without reducing the productivity of the sintered lump.例文帳に追加
焼結塊の生産性を低下させることなく、溶鉱炉内で軟化あるいは溶融しにくい粗酸化亜鉛・鉛焼結塊を安定的に製造する方法を提供する。 - 特許庁
To solve the problem of deterioration in image layer read quality due to a white precipitate on a lens under a high temperature and high humidity environment in the case of using a rod lens array wherein no lead is contained in a close contact image sensor.例文帳に追加
密着型イメージセンサに鉛を含有しないロッドレンズアレーを使用する場合の高温・高湿環境下での白いレンズ析出物による画層読取品質劣化を解決する。 - 特許庁
To analyze a conventional process execution method and restructure it so as to execute all subprocesses constituting the process easily and efficiently and shorten a lead time of the whole process.例文帳に追加
従来のプロセス遂行方法を分析し、プロセスを構成するすべての工程を容易に、しかも効率的に遂行でき、プロセス全体のリードタイムを短縮できるようプロセスを再構築する。 - 特許庁
To provide a filament lamp capable of minimizing non-light-emitting areas between adjacent filaments while arranging an internal lead capable of carrying out independent power supply to each filament.例文帳に追加
各々のフィラメントには独立に給電可能に内部リードを取りまわしつつも、隣り合うフィラメント間の非発光領域を小さく抑えることができるフィラメントランプを提供すること。 - 特許庁
Recessed parts 21a-21h to lead in an adhesive are formed in support holes 18a-18d formed in the connecting members 111, 112 to support the shrink-seal portions 12a-12h respectively.例文帳に追加
シュリンクシール部12a〜12dをそれぞれ支持する連結部材111,112に形成された支持孔18a〜18dには、接着剤を導入させるための凹部21a〜21hを形成する。 - 特許庁
A valve member 48, composed of a control valve 80 and a pressure relief valve 82 which are arranged parallely to each other, is arranged on an oil supplying vapor line 36 lead from a float valve 32 to a canister 34.例文帳に追加
フロート弁32からキャニスタ34へ至る給油時ベーパライン36には、並列配置された、制御弁80と逃し弁82とで構成される弁部材48が配設される。 - 特許庁
To accurately detect remaining capacity of an on-vehicle lead accumulator charged by a generator even after a stop of a vehicle and to perform an idling stop process for a vehicle by using its remaining capacity.例文帳に追加
発電機によって充電される車載の鉛蓄電池の残存容量を車両の停止後でも正確に検出し、その残存容量を用いて車両のアイドリングストップ処理を行う。 - 特許庁
To provide a microwave oven having a good energy efficiency and a good durability while preventing the leakage of electromagnetic wave to the outside of a microwave oven through a lead wire of a heater.例文帳に追加
ヒータのリード線を通して電子レンジ外部へ電波が漏れることを防止するとともに、エネルギー効率が良く、耐久性に優れた電子レンジを提供することを目的とする。 - 特許庁
To stabilize a recording/reproducing characteristic by devising the joint of a detection lens and a beam forming prism which lead a part of light emitted from a laser diode(LD) to an optical detector of a front monitor.例文帳に追加
LDからの射出光の一部を前方モニタ用光検出器に導く検出系レンズとビーム整形プリズムの接合を工夫することにより、記録再生特性を安定させる。 - 特許庁
To provide a probe unit suppressing a contact failure between an electrode of a specimen and a lead wire, and suppressing a damage of the specimen caused by contact with the specimen, and also to provide its manufacturing method.例文帳に追加
検体の電極と導線との接触不良を抑制でき、検体との接触による検体の損傷を抑制することができるプローブユニット及びその製造方法を提供する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|