| 意味 | 例文 |
current valueの部分一致の例文一覧と使い方
該当件数 : 12431件
Prior to feeding to a load device 43, the load device 43 is removed electrically; a passive element 51 is connected in parallel; the output voltage of a variable voltage high-frequency power supply 1 is set to a measurement low voltage V_m; and the output current value I_m of the variable voltage high-frequency power supply 1 at that time is measured.例文帳に追加
負荷装置43への給電に先立ち、負荷装置43を電気的に切り離して、受動素子51を並列接続し、可変電圧高周波電源1の出力電圧を測定用の低電圧V_mに設定して、そのときの可変電圧高周波電源1の出力電流値I_mを測定する。 - 特許庁
An analog circuit 47 connected between a shunt resistor 45 and a drive circuit 46 outputs an analog voltage with a bottom at each approximately 60° in electric angle, and operates the three-phase motor 30 at 30° or below in the absolute value of power factor angle, so that sine wave drive is allowed while current detection is performed in simple configuration.例文帳に追加
シャント抵抗45と駆動回路46の間に接続したアナログ回路47は、ほぼ電気角60度毎にボトムを有するアナログ電圧を出力し、3相電動機30を力率角の絶対値30度以下で運転することにより、簡単な構成で電流検知を行いながらの正弦波駆動が可能となる。 - 特許庁
In a BD reproduction device (an optical disk device) 10 including an optical pickup 11 which has a laser diode 22 to reproduces an optical disk d, a ceiling on the number of retrying related to a servo error or a disk determination mistake is raised when a drive current value which increases according to deterioration in the laser diode 22 exceeds a predetermined threshold.例文帳に追加
光ディスクdの再生を行うレーザダイオード22を有する光ピックアップ11を備えたBD再生装置(光ディスク装置)10において、レーザダイオード22の劣化に応じて増加する駆動電流値が所定の閾値を超えた場合、サーボエラー又はディスク判別ミスに対するリトライ回数の上限を上げる構成とする。 - 特許庁
A transimpedance amplifier has a core circuit 1, which amplifies a current signal and simultaneously converts it into a voltage signal with a transimpedance gain, in proportion to the value of feedback resistance Rf; and a level detection circuit 2, which detects an output amplitude of the core circuit 1 and outputs a control voltage corresponding to the output amplitude detected.例文帳に追加
トランスインピーダンスアンプは、電流信号を帰還抵抗Rfの値に比例するトランスインピーダンス利得によって増幅すると同時に電圧信号に変換するコア回路1と、コア回路1の出力振幅を検出し、検出した出力振幅に応じた制御電圧を出力するレベル検出回路2とを有する。 - 特許庁
To provide a method and device for reducing magnetism on a hull capable of estimating a magnetic field outside the hull even when magnetism on the hull is changed while a ship is on a voyage, and capable of reducing the magnetic field outside the hull at an arbitrary depth by controlling a degaussing current value of all degaussing coils provided in the hull.例文帳に追加
船舶の航行中に船体磁気が変化しても船体外部磁場を推定でき、かつ船体内に設けられたすべての消磁コイルの消磁電流値を制御して任意の深度における船体外部磁場を低減することが可能な、船体の磁気低減方法及び装置を提供する。 - 特許庁
A ROM 10 is built in the CPU 9 and stores a matrix table of voltage behavior to switching current in the temperature and SOC of the battery 1, and the CPU 9 corrects the SOC by comparing a voltage value detected by the voltage detection means 6 and the matrix table of voltage behavior stored in the ROM 10.例文帳に追加
ROM10はCPU9に内蔵され、電池1の温度やSOCにおける、切り替え電流に対する電圧挙動のマトリクステーブルを蓄積し、CPU9は、電圧検出手段6が検出した電圧値と、ROM10に蓄積されている電圧挙動のマトリクステーブルを比較して、SOCを補正する。 - 特許庁
When a double braking is detected during ABS control (the sixth timing t16), an ECU controls a command current value Id for a pressure intensifying valve, which opens when a WC pressure in a wheel cylinder provided corresponding to wheels is intensified, so that a pressure intensifying speed of the WC pressure in the wheel cylinder is increased.例文帳に追加
ECUは、ABS制御中にダブルブレーキが検出された場合(第6タイミングt16)、車輪に対応して設けられたホイールシリンダ内のWC圧の増圧速度が速くなるように、ホイールシリンダ内のWC圧を増圧させる際に開動作する増圧弁に対する指令電流値Idを調整する。 - 特許庁
In hybrid construction machinery, the control section 120 limits the output of the motor generator 12 or the output of the converter 100A to which the motor generator 12 is connected, so that the electric current charged into or discharged from the capacitor is prevented from exceeding a preset allowable value.例文帳に追加
制御部120は、蓄電器への充電電流又は蓄電器からの放電電流が予め設定された許容値を超えないように、電動発電機12の出力又は電動発電機12が接続されたコンバータ100Aの出力を制限することを特徴とするハイブリッド型建設機械。 - 特許庁
As a cause of impossibility of sound output, there is an unconnected state of a loudspeaker 5 or a fault of the loudspeaker 5 or output circuit 63, and when they are caused, the current value becomes smaller or larger than the predetermined range, however, since that is detected in any case, detection can be made to be highly precise.例文帳に追加
音声出力不能の原因としては、スピーカ5の未接続又はスピーカ5若しくは出力回路63の故障があり、これらが生じたときには、上記の電流値が所定範囲よりも小さくなるか、又は、大きくなるが、いずれの場合であっても、それが検知されるので、検知を高精度なものにすることができる。 - 特許庁
Power distribution of the motor 82 is limited with the smaller value of limited current values determined by using the two maps 105, 108.例文帳に追加
発熱量Qの積算値である温度推定値Tに対応する電流上限値を設定した電流上限マップ108と、温度推定値Tに対応するレシオを設定したレシオマップ105とを有し、2つのマップ105、108を使用して決定された制限電流値のうち小さい方でモータ82の通電を制限する。 - 特許庁
To solve the problem wherein applied voltages in three phases differ, when identical high-frequency voltage command is generated on orthogonal two axes and accuracy on the estimation of the position of an initial magnetic pole, using the detecting value of a generated pulsating current deteriorates in a controller and a control method achieving control for a synchronous motor.例文帳に追加
同期電動機の制御を実現する制御装置および制御方法において、直交2軸上で同じ高周波電圧指令を生成すると、三相各相での印加電圧に違いが生じ、発生した脈動電流の検出値を使った初期磁極位置推定の推定精度が悪くなる。 - 特許庁
A control circuit part 17 transmits a command signal for raising output of the constant voltage circuit 1 to the control circuit part 17 of a power source unit-side via a command transmission/reception circuit part 13 when a determining result shows that a necessary constant current value is not obtained in determination of quality of a power source supply state.例文帳に追加
制御回路部17は、電源供給状態の良否の判定において、判定結果が必要な定電流値が得られていないとする場合には、コマンド送受信回路部13を介して、電源ユニット側の制御回路部17に定電圧回路1の出力を上昇させるためのコマンド信号を送信する。 - 特許庁
Then, the CPU 21a determines load difference ΔF between the load when the effect exists corresponding to a motor current value I supplied to the electric actuator 13 at present and the load when the effect has become unworkable, and adds the load difference ΔF to a detected load F input from a load sensor 22 for correction.例文帳に追加
次に、CPU21aは、現在、電動アクチュエータ13に供給しているモータ電流値Iに対応して前記効果が発生している場合の荷重と前記効果が無効化した場合の荷重との荷重差ΔFを決定し、この荷重差ΔFを荷重センサ22から入力した検出荷重Fに加算して補正する。 - 特許庁
The liquid delivery device includes a head for delivering a liquid to a medium, a carriage in which the head is provided, a motor that moves the carriage in a movement direction, a motor driver that controls the driving of the motor, and an estimating section that presumes the temperature of the motor driver based on the current value of the motor driver at a certain point and other points afterwards.例文帳に追加
媒体に液体を吐出するヘッドと、ヘッドが設けられたキャリッジと、キャリッジを移動方向に移動させるモーターと、モーターの駆動を制御するモータードライバーと、ある時点、及び、その後の他の時点でのモータードライバーの電流値に基づいてモータードライバーの温度を推定する推定部と、を備えた。 - 特許庁
A control unit 5 uses a table 81 stored in a storage part 8 to read tube voltage of an X-ray tube 1, tube current, radiography conditions of X-ray including X-ray radiation time when the radiography is performed, and an image processing condition including a central value of luminance and range of the luminance when the image is displayed.例文帳に追加
制御部5は、記憶部8に記憶されたテーブル81を利用して、X線撮影時のX線管1の管電圧、管電流、X線照射時間を含むX線の撮影条件、および、画像を表示するときの輝度の中心値および輝度の幅を含む画像処理条件を読み出す。 - 特許庁
That is, a controller controls the rotation so that the carrier roller operates in response to the target speed locus by adjusting an electric current command value Ir to a driving circuit for driving the motor based on a deviation between the target speed locust and a detecting speed, and achieves carrying control of the sheet corresponding to the target speed locus.例文帳に追加
即ち、制御器は、目標速度軌跡と検出速度との偏差に基づき、モータを駆動する駆動回路への電流指令値Irを調整することにより、搬送ローラが目標速度軌跡に従って運動するように回転制御し、目標速度軌跡に対応したシートの搬送制御を実現する。 - 特許庁
Furthermore, in the structure wherein the photosensor is arranged on each LED unit, white balance of the other LED units are adjusted, on the basis of a current value to each LED unit established, in advance, so as to make output of each photosensor approximately equal and information for determining while balance of one LED unit.例文帳に追加
また、各々のLEDユニットにフォトセンサ部を配置する構成において、予め各々のフォトセンサ部の出力が略等しくなるように設定した各々のLEDユニットに対する電流値と1つのLEDユニットのホワイトバランスを決定する情報とに基づいて他のLEDユニットのホワイトバランスを調整する。 - 特許庁
A back-light control unit 304 determines a target luminance of a back light from input image data Din, and generates an intermediate luminance using a nonlinear function NLF decreasing in variation amount with time to vary the luminance of the back light when the difference between the current luminance of the back light and the target luminance is equal to or larger than a predetermined value.例文帳に追加
バックライト制御部304は、入力画像データDinからバックライトの目標輝度を決定し、バックライトの現在の輝度と目標輝度との差が所定値以上の場合は、時間の経過に応じて変化量が減少する非線形関数NLFを使用して中間輝度を生成し、バックライトの輝度を変化させる。 - 特許庁
To provide an electromagnet device for immediately tripping a circuit breaker which can avoid delay in an immediate tripping operation even when the current set value for immediate tripping is set high, namely even when the gap width between a stable core and a movable iron piece is wide.例文帳に追加
本発明は、瞬時引外し電流設定値を高く調整した場合においても、すなわち固定鉄心と可動鉄片との間の空隙幅を広くした場合においても、瞬時引外し動作の遅延発生を回避できる回路遮断器の瞬時引外し用電磁石装置を提供することを目的とするものである。 - 特許庁
To accurately perform thermal protection of a motor controller equipped with a temperature estimation part in which a motor drive signal of current command or the like is used to estimate the temperature for thermal protection of the motor, an inverter circuit or the like, by suppressing a deviation between the actual temperature and a temperature estimation value of an object to be thermally protected in comparison with a conventional controller.例文帳に追加
電流指令等のモータ駆動信号を使用して温度を推定する温度推定部を具備し、モータやインバータ回路等の熱的保護を行なうモータ制御装置において、熱的保護対象物の実際の温度と温度推定値とのずれを従来よりも抑制することによって、正確に熱的保護を行なう。 - 特許庁
The tester comprises: a measurement section for applying a current to an apparatus under test through a mounting test board for mounting the apparatus under test, and measuring a voltage at a predetermined region in the apparatus under test; and a determination section for obtaining a measurement result from the measurement section, and for determining the acceptance of the apparatus under test by comparing the measurement result with a standard value.例文帳に追加
被測定装置が装着された装着テストボードを介して前記被測定装置に電流を印加し、前記被測定装置の所定部位の電圧を測定する測定部と、前記測定部による測定結果を取得し、規格値と比較することにより、前記被測定装置の合否を判定する判定部と、を具備する。 - 特許庁
The marker lamp includes the heater 108 electrically connected to a light-emitting diode 107 in series, is fed from a constant current power supply device 9, and heats an inner surface side of the translucent member; and a temperature detection means 109 for detecting a temperature of the heater 108 and forming an electric circuit for bypassing the heater, when a detected temperature exceeds a predetermined value.例文帳に追加
発光ダイオード107と電気的に直列関係に接続されて定電流電源装置9から給電され、透光部材の内面をヒータ108と、ヒータ108の温度を検知し、検知温度が所定値以上の場合にはヒータをバイパスする電気回路を形成する温度検知手段109とを有する。 - 特許庁
To provide a charging rate estimation device for a secondary battery capable of reducing delay of an internal resistance estimated value, when the actual internal resistance is increased by a phenomenon in which internal resistance is increased by delay of electron delivery between positive and negative electrodes during discharge of large current from a secondary battery.例文帳に追加
二次電池の大電流放電時に正負極間で電子の受け渡しが追い着かなくなることに起因して内部抵抗が増大するという現象によって実際の内部抵抗が増大した場合に、内部抵抗推定値の遅れを小さく出来る二次電池の充電率推定装置を提供する。 - 特許庁
The PTC element 24, changed into an insulating body by increasing the inherent resistance value of the same in accordance with temperature rise due to heat generating operation upon overcurrent or heating to limit a current delicately, is arranged while connecting the same in series electrically to a lead member 22 between a pair of lead members 22, 23 provided in a capacitor element 21.例文帳に追加
コンデンサ素子21に設けた一対のリード部材22および23のうち、一方のリード部材22に、過電流時または加熱時の発熱作用による温度上昇に応じて固有抵抗値が増大して絶縁体へ変化し電流を微少に制限するPTC素子24を電気的に直列接続して配備する。 - 特許庁
To provide: a composition for manufacturing high thermal-resistance insulated material used for manufacture of an insulating layer 11 or a sheath 13, which is superior in voltage resistance or thermal resistance and can improve flexibility, even if the maximum allowable current value of a center conductor 10 is high; and a high thermal resistance insulated wire manufactured using this.例文帳に追加
中心導体10の最大許容電流値が高くても耐電圧性または耐熱性に優れ、柔軟性を向上できる絶縁層11またはシース層13の製造に用いる高耐熱性絶縁材製造用組成物及びこれを用いて製造された高耐熱絶縁電線を提供する。 - 特許庁
When the power supply is ON and the input voltage value is high, the switch 8a is connected to the (a) side so as to execute full wave rectifying operation and the switch 7a is connected to the (b) side so that a degaussing current is allowed to flow into the coil 13 through a 200 V series positive characteristic thermistor 11.例文帳に追加
さらに、電源オン時で、入力電圧値が高いときには、スイッチ8aをa側に接続して全波整流動作が行われるようにし、スイッチ7aをb側に接続してインピーダンスの大きな200V系正特性サーミスタ11を介してデガウスコイル13にデガウス電流が流れるようにする。 - 特許庁
In order to change the luminance of a part corresponding to the display part 22 according to the luminance change instruction signal, the luminance change circuit 25 adjusts a current value supplied to a 7-segment LED (light emitting diode) unit 220 constituting each display part 22 (22a to 22d) e.g. with variable resistance to change the luminance.例文帳に追加
輝度変更回路25は、輝度変更指示信号に従って表示部22の該当する部分の輝度を変更させるべく、例えば各表示部22(22a〜22d)を構成する7セグメントLEDユニット220に供給される電流値を可変抵抗により調整することで輝度の変更を行う。 - 特許庁
For instance, in a case where dust is attached between the wirings 4 and 10 to cause a sort circuit between them, when the bit 0 of data outputted from the register 114 is '1', the value of a bit 3 inputted into the D/A conversion circuit 112 becomes always '1', and the D/A conversion circuit 112 output an abnormally heavy current.例文帳に追加
したがって、たとえば配線4、10の間にダスト116が付着して配線4、10がショートした場合、レジスター114が出力するデーターのビット0が”1”のときは、D/A変換回路112に入力されるビット3の値も常に”1”となり、D/A変換回路112は異常に大きな電流を出力する。 - 特許庁
Furthermore, the CPU 21 sets an acceptance range for deciding unqualified bidders, i.e., an acceptable price range each time the bid processing is performed and sets the priority amount of the last bid processing to the upper-limit value of the acceptable price range of the current bid processing, i.e., the second and succeeding bid processing.例文帳に追加
さらに、CPU21は、毎回の入札処理で入札資格喪失者を判定するための受付額範囲すなわち受付価格範囲を設定するとともに、2回目以降の各入札処理では、前回の入札処理における優先額を今回の入札処理における受付価格範囲の上限値とする。 - 特許庁
On the basis of an input of a laser output confirmation signal, a control circuit causes a laser output measurement part to measure an output of laser beam and makes a laser output information (laser output value P and rate R) which is based on the measurement result correspond to a date data td about a current time, for acquiring as a composite output data.例文帳に追加
制御回路は、レーザ出力確認信号の入力に基づき、レーザ出力測定部にてレーザ光の出力を測定させ、その測定結果に基づくレーザ出力情報(レーザ出力値P及び割合R)を現在の時刻に関する日付データtdと対応付けて複合出力データとして取得する。 - 特許庁
When the threshold value is exceeded, the automatic control unit 13b starts display from past caption content before the time point of the excess by a predetermined time or a predetermined number of caption display processing units and until caption content corresponding to the current audio can be displayed, allows display of caption content at a predetermined display speed higher than a normal display speed.例文帳に追加
自動制御部13bは、上記閾値を超えた場合、超えた時点より所定時間前又は所定数の字幕表示処理単位分前の過去の字幕コンテンツから現在の音声に対応する字幕コンテンツを表示できるまで、通常の表示速度より速い所定の表示速度で字幕コンテンツを表示させる。 - 特許庁
When the input signal IN is transferred from the Lo level to the Hi level, the transistor MP3 is turned ON until the input signal IN exceeds the logic threshold value, and a High-level input voltage ViH is increased by the current section of the transistor MP4 in the High-level input voltage ViH.例文帳に追加
入力信号INがLoレベルからHiレベルに遷移した際には、トランジスタMP3は入力信号INが論理しきい値をこえるまではONとなり、Highレベル入力電圧ViHは、トランジスタMP4の電流分だけHighレベル入力電圧ViHが上がることになる。 - 特許庁
As a result, when the vehicle is substantially in the stop state, the amplitude of dither current is set to a smaller value by a dither amplitude adjusting circuit 13 of the controller 8.例文帳に追加
ラジオノイズは、従来技術では、車両自体の騒音が小さい低車速または停車中に特に目立つものになっていたが、車両が停車中または設定値i以下で走行している場合にラジオノイズの低減が図れるので、低車速または停車中にもディザ振動に影響されずにラジオ番組などを良好に聴取することができる。 - 特許庁
When output currents Iout are increased to a prescribed value, the voltage of the + terminal of an operating amplifier OP exceeds the voltage (=Vout) of a - terminal due to voltage drop in a current detecting resistance R1, and output currents are allowed to flow from the operating amplifier OP, and the output voltage Vout and the output currents Iout are limited by a transistor Q1.例文帳に追加
出力電流Ioutが増え所定値になると、電流検出用抵抗R1での電圧降下によって、オペアンプOPの+端子の電圧が−端子の電圧(=Vout)を超えるので、オペアンプOPから出力電流が流れ、トランジスタQ1が出力電圧Vout及び出力電流Ioutを制限する。 - 特許庁
Based on the total amount of influences and data from a project planned value table 1012 and a project result table 1013, a project prediction device 1017 calculates the predicted values of yields to be obtained a certain period of time after the current time, resulting costs, completion prediction and the schedule and cost efficiencies, and displays the results on a prediction result display device 1019.例文帳に追加
プロジェクト予測装置1017は、これら総リスク影響量、及びプロジェクト計画値テーブル1012,プロジェクト実績テーブル1013のデータから、現時点から一定期間後の出来高や実績コスト,完了予測,スケジュール効率,コスト効率の予測値を求め、予測結果表示装置1019で表示させる。 - 特許庁
In a step 530, a heat storage rate Pqw as the ratio of the current heat storage amount Qctw to the heat storage amount Qall^w is calculated, and the quantity of the bars according to the value of the heat storage rate Pq^w is lit in the hot water storage amount indication area to indicate the hot water storage amount.例文帳に追加
ステップ530において、蓄熱容量Q_all^wに対する現在蓄熱量Q_ct^wの割合である蓄熱率P_q^wを算出し、この蓄熱率P_q^wの値に応じた本数のバーを、貯湯量表示領域において点灯させることにより、貯湯量を表示する。 - 特許庁
The repeater is constituted so that the difference of the loss in the optical cable is compensated by providing gain control signals by which an output RF signal level transmitted to the portable machine corresponding to the detected current values becomes a stipulated value from control circuits 37, 45 to variable gain amplifiers 36, 46 respectively.例文帳に追加
その検出電流値に対応して無線基地局,携帯機に対して送出する出力RF信号レベルが規定値になるような利得制御信号を制御回路37,45からそれぞれ可変利得増幅器36,46に与えて光ケーブルの損失の差を補正するように構成されている。 - 特許庁
The semiconductor display device characterized in that the display pixels and sensor pixels of a light emitting device have respective light emitting elements, the sensor pixels are mounted with light receiving diodes respectively, and the brightness of the light emitting element of each display pixel is controlled according to a current value flowing through the diode.例文帳に追加
発光装置が有する表示用画素及びセンサ用画素は発光素子をそれぞれ有しており、センサ用画素は受光ダイオードをそれぞれ実装しており、ダイオードを流れる電流の大きさによって、表示用画素がそれぞれ有する発光素子の輝度が制御されていることを特徴とする半導体表示装置。 - 特許庁
The laser light source device has: a semiconductor laser emitting laser beams; and a semiconductor laser drive circuit applying a pulsive drive voltage having a wave height value not less than a laser oscillation start voltage corresponding to a laser oscillation start current of the semiconductor laser to the semiconductor laser to drive the semiconductor laser.例文帳に追加
本発明のレーザ光源装置は、レーザ光を発する半導体レーザと、半導体レーザのレーザ発振開始電流に対応するレーザ発振開始電圧以上の波高値を有するパルス状の駆動電圧を、半導体レーザに印加することにより、半導体レーザを駆動する半導体レーザ駆動回路と、を備える。 - 特許庁
In conducting interviews and/or other supervisory measures, the FSA may focus as to whether each financial institution appropriately recognizes the present value of its positions and the volume of risks by product and by due date, in addition to major focus regarding the market risk that are contained in the current "Comprehensive Guideline for Supervision of Major Banks, etc." 例文帳に追加
ヒアリング等においては、現行の「主要行等向けの総合的な監督指針」における市場リスクに関する主な着眼点のほか、例えば、金融機関による、現在価値ベースのポジション及びリスクの商品別・期日別等の内訳についての適切な把握、といった点を着眼点とすることが考えられる - 金融庁
1) With respect to the solvency margin ratio, the FSA will make improvements to assess the risk more accurately under the current framework in the short run. The FSA will also continue to make efforts at a reform aimed at introducing economic value-based solvency assessment in the medium run, while cooperating with the Institute of Actuaries of Japan and other interested parties. 例文帳に追加
① ソルベンシー・マージン比率について、短期的には現行制度の枠組みの下でリスク評価を精緻化するなどの改善を行うとともに、中期的には経済価値ベースのソルベンシー評価を導入するため、当局において引き続き、日本アクチュアリー会などの関係者と連携しつつ見直しの検討を進める。 - 金融庁
A. In accordance with the categories below, management performance during the corresponding period below shall be included (referring to the performance that allows accurate understanding of the status of investment trust assets, such as net asset value, dividends, rate of fluctuation during the current period beneficiaries yield, stock price indices, composite ratio of major investment target assets or percentage of outstanding principal, etc.). 例文帳に追加
イ.下記の区分に応じ、当該下記に定める期間の運用実績(基準価額、分配金、期中騰落率、受益者利回り、株価指数、主要な運用対象資産の構成比率又は元本残存率等、投資信託財産の状態を的確に判断することができる実績をいう。)が、表示されていること。 - 金融庁
(i) Regarding the top 30 valuations among invested stocks at the end of the current period or on the most recent date as of the formulation of the investment report on investment trust assets, the name of the said stocks, quantity, aggregate market value and investment ratio shall be included. 例文帳に追加
① 当期末現在又は投資信託財産運用報告書作成時点の最近日における投資株式のうち評価額上位30位について発行地又は上場金融商品取引所の区分により地域別に区分し、当該銘柄の名称、数量、時価総額及び投資比率について表示すること。 - 金融庁
(ii) In lieu of (i) above, monetary value and the investment ratio of securities and the place of issuance of stocks and non-stock securities, at the end of the current period or on the most recent date as of the formulation of the investment report on investment trust assets, shall be given by type of securities, place of issuance or region of listed financial instruments exchange, etc. 例文帳に追加
② 上記①に代えて、当期末又は投資信託財産運用報告書作成時点の最近日における投資株式及び株式以外の有価証券について、有価証券の種類別及び発行地又は上場金融商品取引所等の地域別ごとに、金額及び投資比率を表示することができる。 - 金融庁
An operation state (voltage vector) in which an evaluation function J obtained by adding an offset value Δ to the inner product of the difference between predicted currents ide and iqe predicted by a predicting unit 33 and the difference between vectors idr and iqr of a command current is the minimum is determined as the operation state of an inverter IV.例文帳に追加
予測部33によって予測された予測電流ide,iqeのベクトルと、指令電流のベクトルidr,iqrとの差の内積値にオフセット値Δを加算したものである評価関数Jを最小とする操作状態(電圧ベクトル)が、インバータIVの操作状態として決定される。 - 特許庁
In the low-temperature battery mode, a brightness threshold for setting photographing sensitivity is forcedly set by the control of a system LSI11, to a value that the photographing sensitivity is always high independently of the brightness of an object; and a charging current of a capacitor for driving light emission of a flash 19 is set lower than a predetermined threshold.例文帳に追加
この低温電池モードでは、システムLSI11の制御によって、撮影感度を設定するための明るさの閾値を被写体の明るさに依らず撮影感度が常に高くなるような値に強制的に設定するとともに、フラッシュ19を発光駆動するコンデンサの充電電流を所定の閾値より低く設定する。 - 特許庁
To obtain a DC power supply that clears high-frequency control, efficiency, a power factor, and noise suppression when providing a switching section for enabling current to flow to a reactor forcedly in the DC power supply provided in the pre-stage of the inverter device, and can switch the switching section to reduce the inductance value of the reactor.例文帳に追加
インバータ装置の前段に設ける直流電源装置に、リアクトルに強制的に電流を流すスイッチング部を設ける場合において、高調波規制や効率、力率、ノイズ抑制をクリアしつつ、リアクトルのインダクタンス値の低減が可能となるようにスイッチング部をスイッチング制御できる直流電源装置を得ること。 - 特許庁
Two or more wiring patterns having current directions different from each other are formed in the layer stacking direction through an insulator by at least partially overlapping them on each other in an area between the key top part 3a and the key top part 3b and in an area where its space width size W is smaller than the height value (h) of the key top part.例文帳に追加
キートップ部3aとキートップ部3bの間領域であって、その間隔幅寸法Wがキートップ部の高さ値hよりも小さい領域に、電流方向を異にする2以上の回路配線を層の重なり方向に絶縁体を介して少なくとも部分的に重ねて敷設している。 - 特許庁
It is determined that the battery is fully charged, when a state continues for a certain time T_20 with the difference between a command voltage of the battery at charging time and its effective voltage being lower than a given value and when a state continues for a certain time T_10 that a battery current I is lower than a prescribed threshold I_0.例文帳に追加
充電時におけるバッテリの指令電圧とバッテリの実電圧との差が所定値を下回る状態が一定時間T_20だけ継続し、かつ、バッテリ電流Iが所定のしきい値I_0を下回る状態が一定時間T_10だけ継続する場合に、バッテリが満充電状態にあると判定する。 - 特許庁
Furthermore, a high voltage power source 22 is controlled by the control device 20 so that current (this can also be applied voltage) fed to the photoreceptor 1 from a discharge electrode 11 is adjusted so that discharge electric field of the discharge electrode 11 is strengthened each time discharge time measured by a timer 23 reaches a value that is set before hand.例文帳に追加
また、制御装置20は、タイマ23が計測した放電時間が予め設定した値になる度に放電電極11の放電電界を強めるように、その放電電極11から感光体1に流す電流(印加電圧でもよい)を調整するように高圧電源22を制御する。 - 特許庁
| 意味 | 例文 |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|