| 例文 |
quantity setの部分一致の例文一覧と使い方
該当件数 : 2362件
In CI-SI combustion, effective compression ratio is set smaller than that in CI combustion, injection quantity of the ignition fuel is reduced, and air fuel pre-mixture is burned with flame propagation combustion with trigger by self ignition combustion of the ignition fuel.例文帳に追加
CI−SI燃焼では、CI燃焼に比べ、有効圧縮比を小さく、着火用燃料の噴射量を少なくし、この着火用燃料の自己着火燃焼をトリガとして予混合気を火炎伝播燃焼させる。 - 特許庁
To provide a lubricating structure of a differential device that hardly causes seizure due to a lack of lubrication in a front side tapered roller bearing when starting a vehicle, even if the total quantity of lubricating oil in the differential device is set small.例文帳に追加
ディファレンシャル装置内の潤滑油の全体量を少なく設定しても、車両の始動時にフロント側の円すいころ軸受において潤滑不足による焼き付きが発生し難いディファレンシャル装置の潤滑構造を提供する。 - 特許庁
Thereafter, the adjustment and the replenishment of the liquid are performed based on the replenishing pattern selected and set in accordance with the capacity of the developing tank and the PS plate to be processed, so that the desired quantity of liquid and target electric conductivity are obtained (step 216).例文帳に追加
この後に、現像槽内の容量や処理するPS版に応じて選択されて設定された補充パターンに基づいて調整補充を行い、所望の量及び目標の電導度となるようにする(ステップ216)。 - 特許庁
If the output voltage Vp of a sensor that receives reflected light from the surface of an intermediate transfer belt is within a predetermined range #1 when a light quantity control signal S1c is set to a predetermined value S1c(2), it is determined that the sensor is normal.例文帳に追加
光量制御信号Slcを所定値Slc(2)に設定したときに、中間転写ベルト表面からの反射光を受光するセンサの出力電圧Vpが所定範囲#1内にあれば、センサは正常と判定する。 - 特許庁
To provide a mono-lever operating device capable of improving fine control characteristics by reducing the clearance of a mono-lever at a neutral position, and improving abrasion resistance, and reducing the change of a set speed, and regulating the stroke quantity of a control lever adjustable from the outside.例文帳に追加
モノレバーの中立時の遊びを小さくしてファインコントロール特性が良く、かつ、耐摩耗性が良くて設定速度の変化が少なく、外部より調整可能な操作レバーのストローク量の規制ができるモノレバー操作装置を提供する。 - 特許庁
Data processing is carried out in the middle of image processing to image data of the edge part where no margin is set or of a predetermined region along the edge part, thereby lowering the density of the region to reduce an ink application quantity at the edge part.例文帳に追加
余白が設けられない縁部ないしこれに沿った所定領域の画像データに対し、画像処理の過程でデータ加工を行うことで、当該領域の濃度が低減されるようにし、縁部でのインク付与量を小さくする。 - 特許庁
Meanwhile, when the low-load continuation counter CT is less than a reference value Ctth, it is determined that the frequency of execution of the low-load operation of the engine 200 is relatively low, and the power supply quantity W is set to a normal value W2.例文帳に追加
一方、低負荷継続カウンタCTが基準値Ctth未満であれば、エンジン200の低負荷運転の実行頻度が相対的に低いものとして、当該通電量Wが通常値W2に設定される。 - 特許庁
In a steering acceleration state, the fore-and-aft driving force distribution cooperation control gain is set to be low when it can be judged that the vehicle is on a high μroad because of high actual lateral acceleration, and control quantity by the fore-and-aft driving force distribution control is lowered.例文帳に追加
操舵加速状態において前後駆動力配分協調制御ゲインは、実横加速度が高く高μ路と判断できる場合には低く設定して前後駆動力配分制御による制御量を低くする。 - 特許庁
Besides, although it is possible to determine the light quantity by performing firm measurement with a measuring means, the interval deviation to be corrected is measured and recorded previously to input the set value when there are few periodic variation by aging.例文帳に追加
また、測定手段で常時測定し、光量を決定する事が可能であるが、周期性の経時変化が少ない場合は、予め、補正すべき間隔ずれ量を測定記録し、その設定値を入力するようにしてもよい。 - 特許庁
The LED elements L1 to L22 are divided into two groups G1 and G2, and set so that the irradiating light quantity of the LED elements L12 to L22 of the group G2 on a front side is made smaller than that of the LED elements L1 to L11 of the group G1 on an inner side.例文帳に追加
LED素子L1〜L22を2つのグループG1,G2に分け、奥側のグループG1のLED素子L1〜L11の照射光量よりも、前側のグループG2のLED素子L12〜22の照射光量を少なくする。 - 特許庁
The hot water filling temperature is set low by expecting a temperature rise quantity by the pump circulation for confirming the water level at hot water filling time to the hot water filling temperature set by the bather so that a hot water filling end time temperature becomes a preset temperature.例文帳に追加
浴槽へのお湯はり量及びお湯はり温度の自動設定機能を有する貯湯式全自動風呂給湯装置において、お湯はり温度を、入浴者が設定したお湯はり温度に対し、お湯はり中に水位確認をするためのポンプ循環による温度上昇分を見込んで低めに設定し、お湯はり終了時の温度が設定温度になるようにした。 - 特許庁
With such a constitution taken, if a pressure of the liquefied gas in the gaseous phase passing through the pipe line 5 becomes less than a set value set by the detecting means 13, the liquefied gas in the gaseous phase is fed at the pressure more than the desired pressure since a quantity of vaporization is increased by heating the liquefied gas with the heating section through which the heat medium passes.例文帳に追加
このような構成とすれば、ガス管路5を通流する気相の液化ガスの圧力が圧力検知手段13に設定された圧力以下になった場合、熱媒が通流する加熱部によって液化ガスが加熱されて気化量が増えるため、所定の圧力以上で気相の液化ガスを供給することができる。 - 特許庁
Then, when the fuel injection is inhibited based on the load rate KL of the engine, a command power Pe* of the engine is set so as to be more smoothly changed than the case that the fuel injection is not inhibited, and that the firing of mixture is carried out, and the intake air quantity Qa of the engine is controlled based on the set command power Pe*.例文帳に追加
そして、エンジンの負荷率KLに基づいて燃料噴射が禁止されているときには、燃料噴射が禁止されておらずかつ混合気の燃焼が行われるときに比べて緩やかに変化するようにエンジンの指令パワーPe*を設定し、設定された指令パワーPe*に基づいてエンジンの吸入空気量Qaを制御する。 - 特許庁
At the movement quantity detection part 40, a plurality of 1st lateral movement evaluation areas including 22 mutually adjacent longitudinally long divided areas are set for a specified image and a plurality of 2nd lateral movement evaluation areas including 22 mutually adjacent longitudinally long divided areas are set for images succeeding to the specified image with time.例文帳に追加
移動量検出部40では、所定の画像に対して互いに隣接し合う22個の縦長分割エリアを含む第1横移動評価エリアを複数設定する一方で、所定の画像と時間的に連続する画像に対して互いに隣接し合う22個の縦長分割エリアを含む第2横移動評価エリアを複数設定する。 - 特許庁
When the status flag F is set (Flag=1), namely, the last input level APL finely varies and increases by the reference value, as shown in section (e), the value obtained by subtracting the fine variation quantity (a unit quantization step width, as the reference value in this example) from the input level APL is set as the output level APLad.例文帳に追加
状態フラグFがセット状態(Flag=1)、つまり直前までの入力レベルAPLが微少変動し、しかも区間eのように、入力レベルが基準値だけ上昇する方向に変動しているときには、入力レベルAPLから微少変動分(この例では基準値である単位量子化ステップ幅)だけ減算した値が、出力レベルAPLadとして設定される。 - 特許庁
An electronic control device 80 changes over set fuel pressure FP in the delivery pipe 30 in the plurality of steps by controlling a change over valve 40 according to the operation state of the engine 50, and controls fuel supply quantity injected from the fuel injection valve 31 through adjustment of open timing of the fuel injection valve 31 corresponding to the set fuel pressure FP.例文帳に追加
電子制御装置80は、機関50の運転状態に応じて切替弁40を制御することにより、デリバリパイプ30の設定燃圧FPを複数段階に切り替え、設定燃圧FPに対応した燃料噴射弁31の開弁期間の調整を通じて燃料噴射弁31から噴射する燃料供給量を制御する。 - 特許庁
A soda lime silicate glass or borosilicate glass subjected to chemical strengthening, a borosilicate glass containing no or small quantity of Na2O, an alkali-free glass or a crystallized glass is employed as the glass material and the arithmetic mean surface roughness Ra of the glass substrate is set at 0.5 nm or less and the maximum height Ry is set at 10 nm or lower.例文帳に追加
ガラス材質としてソーダライムシリケートガラスまたはボロシリケートガラスを化学強化処理したもの、あるいはNa_2 Oの含有量の少ないまたはNa_2 Oを含有しないボロシリケートガラス、無アルカリガラスまたは結晶化ガラスを用い、ガラス基板表面の算術平均粗さRaを0.5nm以下、かつ最大高さRyを10nm以下にする。 - 特許庁
When a controller recognizes there is a shortage of quantity in the power supply of the first generation, the controller causes the hydrogen apparatus 7 and the oxygen apparatus 8 for supplying hydrogen and oxygen to a fuel cell power generating set 9, and causes the generating set 9 to conduct second power generation using the oxygen and hydrogen, and supplying of power is obtained.例文帳に追加
そして、コントローラが、第1電力発電の供給量に対する不足を認識すると、水素貯蔵装置7と酸素貯蔵装置8から燃料電池発電装置9へ水素と酸素を供給させ、燃料電池発電装置9において水素と酸素を利用した第2電力発電を行わせて、供給電力をまかなう。 - 特許庁
A measuring instrument 1 receives a measurement start signal from a data processor 3, measures a physical quantity by itself at a set sampling speed according to previously set parameters, stores measurement data in a RAM, monitors the free state of a communication line 2 and sends the measurement data to the data processor 3 when the communication line 2 is free.例文帳に追加
測定装置1は、データ処理装置3からの測定開始信号を受けて、予め設定されたパラメータに基づき、設定されたサンプリング速度で物理量を自立的に測定し、該測定したデータをRAMに格納し、通信路2の空き状態を監視して通信路2が空いている時に測定データをデータ処理装置3側に送信するようにする。 - 特許庁
The integration circuit 11 has a variable capacitance section to which any one of a plurality of capacitance values is set selectively, stores charges in the variable capacitance section, which are output from a photodiode for a storage period corresponding to the capacitance value being set to the variable capacitance section, and outputs a voltage value V_1 corresponding to the stored charge quantity.例文帳に追加
積分回路11は、複数の容量値のうちの何れかの容量値に選択的に設定される可変容量部を有し、可変容量部において設定されている容量値に対応した蓄積期間に亘ってフォトダイオードから出力される電荷を可変容量部に蓄積して、蓄積した電荷の量に応じた電圧値V_1を出力する。 - 特許庁
When the driver manipulates the control switch 26, a volume input value Vo is calculated according to the operation quantity (S1), the maximum throttle sensitive torque TQ1 and the minimum throttle sensitive torque TQ2 are set (S2, S3) based on a throttle opening θth, and a volume correction gain G is set based on the volume input value Vo (S4).例文帳に追加
運転者がコントロールスイッチ26を操作すると、その操作量に応じたボリューム入力値Voを算出し(S1)、又スロットル開度θthに基づいて最大スロットル感応トルクTQ1、最小スロットル感応トルクTQ2を設定し(S3,S4)、更にボリューム入力値Voに基づきボリューム補正ゲインGを設定する(S4)。 - 特許庁
Thus, when a substrate G is displaced upward more than set floating altitude Hb according to the fluctuation of the vacuum pressure of the vacuum mechansim, a resist nozzle 78 is also displaced upward by almost the same displacement quantity in the same timing as that of the displacement of the substrate G, and a gap S between the resist nozzle 78 and the substrate G is held at a set value as a result.例文帳に追加
これにより、たとえば、バキューム機構の真空圧力の変動に応じて基板Gが設定浮上高度H_bよりも上方へ変位するときは、その基板Gの変位と同じタイミングでレジストノズル78も上方へほぼ同じ変位量だけ変位し、結果的にレジストノズル78と基板GとのギャップSが設定値に保たれる。 - 特許庁
In the document set position, when detecting a document bundle on a document tray by a set switch 603, when an upper limit switch 311 detecting that the lifting plate exists in the carrying proper position is in an off-state, a preliminary operation control part 602 drives a lift motor 503 so as to be liftable by a backlash quantity of a driving system gear of the lifting plate.例文帳に追加
原稿セット位置において、セットスイッチ603により原稿トレイ上の原稿束が検出された際に、昇降板が搬送適正位置にあることを検出する上限スイッチ311がオフ状態である場合、予備動作制御部602は昇降板の駆動系ギアのバックラッシュ分だけリフトモータ503を上昇駆動する。 - 特許庁
For example, when the degradation of the front stage catalyst (FCC) is small, the air fuel ratio is set in an area A, and when the degradation of the front stage catalyst is large, the air fuel ratio is set in an area B so that an NOx and THC quantity (after TWC) supplied to the NOx catalyst can be held almost constant regardless of the degradation degree of the front stage catalyst.例文帳に追加
例えば、前段触媒(FCC)の劣化小のときには領域A内で空燃比を設定し、前段触媒が劣化大のときには領域B内で空燃比を設定することにより、前段触媒の劣化度合に関わらず、NOx触媒に供給されるNOx及びTHC量(TWC後)をほぼ一定に保持する。 - 特許庁
A representative gradation D is set within a gradation range (A<Y<B) in color adjusting area to set the boundary gradation adjusting quantities W1 and W2 of the upper limit gradation A and the lower limit gradation B of the color adjusting area to be V/2, e.g. in accordance with a gradation adjusting quantity V to each pixel in the cooler adjusting area.例文帳に追加
色調整領域の階調範囲(A<Y<B)内に代表階調Dを設定し、色調整領域の上限の境界階調Aおよび下限の境界階調Bの境界階調調整量W1,W2を、色調整領域内の各画素に対する階調調整量Vに応じて、たとえばV/2に設定する。 - 特許庁
In executing an analysis for isolating an objective constituent, a low flow rate set by considering a moving time of a mobile phase branched into two passages by a splitter 11 is set for the pump 16, and after isolating the objective constituent, the flow rate of the pump 16 is increased to run a large quantity of the mobile phase from the analysis passage 12 to a mass spectrometer 9.例文帳に追加
目的成分を分取するための分析実行時には、スプリッタ11で二経路に分岐された移動相の移動時間を考慮した低流量をポンプ16に設定し、目的成分が分取された後には、ポンプ16の流量を増加させて分析流路12から質量分析計9に多量の移動相を流す。 - 特許庁
Based on the acquired luminance, emitted light quantity in the regular light emission is set and also low transmittance is set to a light distribution control part 16 as the transmittance of part of the plurality of liquid crystal elements forming the light distribution changing part 15 corresponding to the partial area having the luminance exceeding saturation luminance, whereby part of the strobe light in the regular light emission is dimmed.例文帳に追加
取得した輝度に基づいて、本発光における発光量が設定されると共に、飽和輝度を超える輝度を有する部分領域と対応する配光変更部15をなす複数の液晶素子の一部の透過率に、低い透過率が配光制御部16に設定されて本発光におけるストロボ光の一部が減光される。 - 特許庁
A data process quantity (sectional area of a column at operation and specification level or a quadrangular prism at RT level) per unit time of a bus is set, a core having a desirable function is extracted from a database and selected as an element, and connection parts from a connection surface of a bus and the bus to the bus are set to determine the connection relation between the bus and respective elements.例文帳に追加
バスの単位時間当たりのデータ処理量(動作・仕様レベルでは円柱の断面積,RTレベルでは四角柱の断面積)を設定し、データベースから所望の機能を有するコアを抜き出してこれを要素として選択し、バスの接続面やバスから要素への接続部の設定などを行なって、バスと各要素との接続関係を決定する。 - 特許庁
Also, at least one of the formed position, formed quantity, and diameter dimension of the lateral communication hole 24 along the circumferential direction of the union 18 is set so that the turn and deflection of the fluid flowing through the fluid passage 20 can be suppressed.例文帳に追加
またしかも、連通横穴24のユニオン18周方向に沿った形成位置、形成個数、及び径寸法のうち少なくとも何れか一つは、流路20を流れる流体の旋回及び偏向が抑制されるように設定されている。 - 特許庁
To provide an electronic endoscope system which can keep a light source for usual observation and a light source for PDT (photodynamic therapy) arranged in the same apparatus and confirm the intensity of treatment light at the time of performing PDT to automatically set the treatment light to proper light quantity.例文帳に追加
通常観察用の光源とPDT用の光源とを同一の装置内に配置することができ、かつ、PDTの実行時の治療光の強度を確認して自動的に適切な光量となるよう設定できるシステムを提供すること。 - 特許庁
An impedance control circuit 31 repeats a control action which changes an impedance of its own apparatus so that the output voltage of the rectifier circuit 22 becomes equal to the desired voltage set value, thereby controls a quantity of received power from the electromagnetic field transmission apparatus 1.例文帳に追加
インピーダンス制御回路31は、整流回路22の出力電圧が所望の電圧設定値となるよう自装置のインピーダンスを変化させる制御動作を繰り返し行い、電磁場送信装置1からの受信電力量を制御する。 - 特許庁
In this optical system, the angle between an incident optical axis L and a scanning optical axis Ls is set to be 65 degrees, the incident optical axis L is moved by a predetermined distance toward an fθ 30 lens side, and the optical axis is adjusted for uniformizing light quantity.例文帳に追加
この光学系では、入射光軸Lと走査光軸Lsとのなす角度を65度に設定し、入射光軸Lはfθレンズ30側へ所定距離移動され、またその光軸は光量均一化のために調整される。 - 特許庁
When a layer having an optical film thickness k×(λ_0/4) is formed for a target wavelength λ_0, the wavelength of monitor light is set to λ_0/2 and the deposition of the layer is ended at the point when the quantity of monitor light exceeds a (2×k)th extreme value.例文帳に追加
目的の波長λ_0に対して、光学膜厚がk×(λ_0/4)の層を成膜する場合、モニター光の波長をλ_0/2とし、モニター光量が2×k番目の極値を迎えた時点でその層の成膜を終了するようにする。 - 特許庁
The second background plate 90 of a second background part 84 is allowed to emit light, and the quantity level of light of the second background plate 90 photographed by the rear camera 54 is set more than that of the normal grains of the sorting grains G photographed by the rear camera 54.例文帳に追加
さらに、第2背景部84の第2背景板90が発光可能にされて、リヤカメラ54が撮影する第2背景板90の光量レベルが、リヤカメラ54が撮影する選別粒Gの正常粒の光量レベル以上にされている。 - 特許庁
To provide a joint for a cable protective conduit which allows the end positions of inner tubes within mounting pipes to be put in set positions without fail and a specified quantity of expansion and contraction to be secured, and a construction method for a cable protective conduit using this joint.例文帳に追加
取付管内における内管の端部位置を、設定された位置に確実に配置することができ、所定の伸縮量を確保することができるケーブル保護管路用継手及びこの継手を用いたケーブル保護管路の施工方法を提供する。 - 特許庁
Moreover, after a design service life time of a humidity sensor passes, when the air supply humidity exceeds a deterioration determination reference value set lower than the operation switching reference value, the control part stops the air supply air blower, or performs intermittent operation or air quantity reduction operation of the air supply air blower.例文帳に追加
制御部は、更に湿度センサーの設計寿命時間を経過した後には、給気湿度が運転切換基準値より低い劣化判定基準値を超えると、給気送風機を停止、間欠運転もしくは風量減運転する。 - 特許庁
A color difference ΔE between a target chromatic value indicated by photometric data MD acquired by applying colorimetric processing to a target TG under a plurality of light sources and a predicted chromatic value in printing by a printer based on an ink quantity set ϕ is calculated for each of the light sources.例文帳に追加
ターゲットTGを複数光源下において測色して得られた測色データMDが示すターゲット色彩値と、インク量セットφに基づいてプリンタが印刷を行ったときの予測色彩値との色差ΔEを各光源について算出する。 - 特許庁
When variation of intake air quantity between banks of V-type engine is learned, a target value of lift operation angle variable mechanism provided on each bank is set to a target value for learning with which flow velocity of intake air passing through the intake valve is roughly acoustic velocity.例文帳に追加
V型機関におけるバンク間の吸入空気量のばらつきを学習するときに、各バンクに設けられるリフト・作動角可変機構の目標値を、吸気バルブを通過する吸気の流速が略音速になる学習用の目標値とする。 - 特許庁
A glass container is irradiated with ultraviolet rays from an ultraviolet floodlight projector 1 and the ultraviolet rays transmitted through the glass container are received by an ultraviolet sensor 2 and, when the quantity of the transmitted ultraviolet rays is less than a set value, the coating film of the glass container is judged to be defective.例文帳に追加
紫外線投光器からガラス容器に向かって紫外線を照射し、ガラス容器を透過した紫外線を紫外線センサで受光し、その紫外線の量が設定値よりも少ないときに、ガラス容器のコーティングが不良であると判定する。 - 特許庁
According to this constitution, both of the steam supply quantity to the cooking chamber 4 and the inside temperature of the cooking chamber 4 can be stabilized, and the inside temperature of the cooking chamber 4 can be risen to the set value in a short time.例文帳に追加
この構成の場合、調理室4に対する水蒸気の供給量および調理室4の庫内温度の双方を安定化することができ、しかも、調理室4の庫内温度を設定値に短時間で昇温することができる。 - 特許庁
The smallest fuel injection ratio Kmin of the first fuel injection valve, at which the injection temperature of the first fuel injection valve is lower than a set temperature that prevents the accumulation of deposit, is determined based on an intake air quantity Ga and engine temperature Tw.例文帳に追加
第一燃料噴射弁の噴孔温度がデポジットの堆積を防止可能な設定温度以下となる第一燃料噴射弁の最小燃料噴射割合Kminを、吸入空気量Gaと機関温度Twとに基づき決定する。 - 特許庁
According to the diviated quantity of the forming positions of dots D1 to D192 caused by the inclination of the recording head, a recording resolution in the main scan direction is associated with the number of partitions of nozzle group at carrying out a so-called block drive for the recording head and set therewith.例文帳に追加
記録ヘッドの傾きによるドットD1からD192の形成位置のずれ量に応じて、主走査方向における記録解像度と、記録ヘッドをいわゆるブロック駆動するときのノズル群の分割数と、を関連づけて設定する。 - 特許庁
The temperature of a mold cavity on the design face side is set higher than the temperature of the mold cavity on the opposite design face side, and a material C to be gasified by the heat quantity of a resin injected and filled into the mold cavity 15 on the opposite design face side is applied.例文帳に追加
意匠面側の金型キャビティ温度を反意匠面側の金型キャビティ温度より高く設定するとともに、反意匠面側の金型キャビティ15に射出充填した樹脂の熱量でガス化する材料Cを塗布する。 - 特許庁
A unit load quantity generation program 72 operated on a computer 1 performs control to components (50-58) of the system, and starts or stops the environmental load reducing function of each component to set each component to a desired measurement condition.例文帳に追加
コンピュータ1上で動作する単位負荷量生成プログラム72は、システムの構成部分(50〜58)に対する制御を行い、各構成部分の環境負荷軽減機能を起動したり停止したりして、各構成部分を所望の測定条件に設定する。 - 特許庁
To provide a display device for a vehicle wherein the size of a liquid crystal display can be set corresponding to the quantity of information to be displayed by enhancing the degree of freedom of a layout combined with an analog meter, while an increase of manufacturing costs is suppressed.例文帳に追加
製造コストの上昇を抑制しつつ、アナログメータとの組み合わせレイアウトの自由度を向上させて、表示する情報量に応じた液晶表示装置の大きさを設定することができる車両用表示装置を提供する。 - 特許庁
To provide a method of manufacturing an optical fiber preform by which it is prevented that a core rod set inside is moved and damaged by a gas flow even when a sufficient quantity of a treating gas is supplied in the jacketing of a clad tube and the core rod.例文帳に追加
クラッドチューブとコアロッドのジャケッティングの際に、チューブ内に十分な量の処理ガスを供給しても、そのガス流によって内部にセットされたコアロッドが移動し、傷を付けることのない光ファイバ母材の製造方法を提供する。 - 特許庁
A method for settling inspection result arranges components of the same component type determined as defective by the automatic visual inspection in a feature space by feature quantity extracted from each image to perform clustering processing, and settles non-defective or defective for each established set C1, C2.例文帳に追加
自動外観検査で不良と判定された同一部品種の部品を、それぞれの画像から抽出された特徴量による特徴空間に配置してクラスタリング処理を実行し、設定された集合C1,C2毎に良・不良を確定する。 - 特許庁
The wireless communication system selection section 14 selects a wireless communication system used by the data communication card 10 on the basis of the communication data quantity measured by the data monitor section 12 and the communication quality set by the communication quality setting section 13.例文帳に追加
無線通信方式選定部14は、データ監視部12により測定された通信データ量と、通信品質設定部13により設定された通信品質とに基づいて、データ通信カード10が使用する無線通信方式を選定する。 - 特許庁
When a control unit 31 of a photoelectric sensor 30 accepts an instruction to execute scaling display, a scaling adjustment ratio is calculated by assigning a received light quantity to a target value set to a value larger than a display upper limit value while executing the scaling display.例文帳に追加
スケーリング表示の実行指示を光電センサ30の制御部31が受け付けた際に、スケーリング表示実行中の表示上限値よりも大きな値に設定された目標値に受光量を割り当ててスケーリング調整率を算出する。 - 特許庁
To grasp an ink residual quantity in an ink cartridge by a level of several phases at a simple means which utilizes a prism part set at an ink cartridge bottom face, and to display warning of an ink cartridge replacement by a suitable timing according to the grasped level.例文帳に追加
インクカートリッジ底面に設けられたプリズム部を利用した簡単な手段にインクカートリッジ内のインク残量を何段階かのレベルで把握するとともに、把握したレベルに応じて適切なタイミングでインクカートリッジ交換の警告を表示する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|