| 例文 |
from zeroの部分一致の例文一覧と使い方
該当件数 : 1782件
The phase difference between a zero-cross signal of a motor current, detected from a motor terminal voltage with an electric current phase detecting part and the command voltage, is detected with a phase difference generating part, and the sensor-less drive of motor is realized, by controlling the phase of the command voltage with the command voltage generating part so that the phase difference becomes substantially zero.例文帳に追加
電流位相検出部にてモータ端子電圧から検出したモータ電流のゼロクロス信号と、指令電圧との位相差を位相差生成部で検出し、位相差が実質的にゼロとなるように、指令電圧生成部にて指令電圧の位相を制御することでモータのセンサレス駆動を行う。 - 特許庁
In the ozone generator equipped with the ozone generation unit 1, the zero gas inlet tube 2 for feeding the zero gas to the ozone generation unit 1, and the ozone gas outlet tube 3 for sending the ozone-containing gas from the ozone generator to the outside, the filter-chargeable filter cassette 4 is interposed into the ozone gas outlet tube.例文帳に追加
オゾン発生部1と、オゾン発生部1にゼロガスを供給するゼロガス入口管2と、オゾン発生部1で発生したオゾンを含有するガスを外部に送出するオゾンガス出口管3とを備えるオゾン発生器において、フィルターを装填可能なフィルターカセット4をオゾンガス出口管3に介装した。 - 特許庁
Therefore, the leakage current flowing from an AC power supply 5 side to a power converter becomes substantially zero, a DC current generated in the rectifying smoothing circuit part 2 of the rear stage of the zero-phase current transformer 21 can be supplied to the amplifier circuit 22, and the amplification degree of the amplifier circuit 22 can be accurately set to 1.例文帳に追加
このため、交流電源5側から電力変換装置に流入する漏れ電流は、ほぼ零になり、零相変流器21の後段の整流平滑回路部2が生成した直流電圧を増幅回路22に供給することができ、しかも増幅回路22の増幅度を正確に1にすることができる。 - 特許庁
The induction motor 3 is controlled with the total torque command value τ* obtained as the sum of the two values, wherein the torque bias command value τ***is raised from zero to the specified value at the first change rate along with the operation start command for the induction motor 3, and with the stop command, the torque bias command value τ*** is lowered to zero with the second change rate.例文帳に追加
この両者の和である合計トルク指令値τ^* で誘導電動機3を制御するが、誘導電動機3の運転開始指令と共に前記トルクバイアス指令値τ^***を零から第1の変化率で所定値まで上昇させ、停止指令と共にこのトルクバイアス指令値τ^*** を第2の変化率で零まで低下させる。 - 特許庁
In SBW_ECU of this steering gear for a vehicle, an off condition of the ignition switch is detected to output off-notification in Step S101, and vehicle speed information is fetched from ABS_ECU and the vehicle speed of zero per hour (0 km/h) is detected to output vehicle body zero information in Step S105.例文帳に追加
本車両用操舵装置のSBW_ECU では、ステップS101により、イグニッションスイッチのオフ状態を検出しオフ通知を出力し、ステップS105により、ABS_ECU から車速情報を取得し車速が時速ゼロ(0km/h)であることを検出し車速ゼロ情報を出力する。 - 特許庁
The device for compensating for signal distortions caused by noise is provided with a noise reduction unit, adapted to reduce noise of an input signal including non-zero mean random noise; and a signal-compensating unit, adapted to compensate the output signal of the noise reduction unit with signal distortions due to non-zero mean random noise eliminated from the output signal of the noise reduction unit.例文帳に追加
非ゼロ平均ランダムノイズを含む入力信号のノイズを低減するノイズ低減部と、ノイズ低減部の出力信号から非ゼロ平均ランダムノイズによる信号歪曲が除去された形態でノイズ低減部の出力信号を補償する信号補償部と、を備えるノイズによる信号歪曲補償装置である。 - 特許庁
Luminous flux from a laser diode light source 11 of a rotary encoder becomes parallel luminous flux I1 by a collimator lens 12, and the luminous flux 11 is partially reflected by a half mirror 13 and enters a zero- point detection part Z of a rotary disk 14 that rotates with a rotary axis 14a as a center as zero-point detection luminous flux I2.例文帳に追加
レーザーダイオード光源11からの光束は、コリメータレンズ12で平行光束I1となり、ハーフミラー13によりこの光束I1の一部が反射され、原点検出光束I2として回転軸14aを中心に回転する回転ディスク14の原点検出部分Zに入射する。 - 特許庁
When the cell has been fitted, an operation for detecting a zero-point position by a reference position detection part 32 continues, and the zero-point position of grating is detected based on an electrical signal from a photosensor 14 and a pulse signal for drive being sent to a motor 16 for driving grating and is stored at a storage part 34.例文帳に追加
セルが装着されている場合、基準位置検出部32による原点位置を検出する動作を続行し、光センサ14からの電気信号及びグレーティング駆動用モータ16に送る駆動用パルス信号に基づいてグレーティング10の原点位置を検出し、記憶部34に記憶する。 - 特許庁
(b)in the case where changes to the contributions paid by Members is zero or greater, the amount (limited to an amount of zero or greater) determined by the Member Commodity Exchange Surviving an Absorption-Type Merger pursuant to the provisions of an Absorption-Type Merger contract within the scope of the amount obtained by deducting the amount set forth in (b) of the preceding item from said changes of contributions paid by Members; 例文帳に追加
ロ会員払込出資変動額が零以上の額であるときは、当該会員払込出資変動額から前 号ロに掲げる額を減じて得た額の範囲内で、吸収合併存続会員商品取引所が吸収 合併契約の定めに従い定めた額(零以上の額に限る。) - 経済産業省
Furthermore, the controller 37 executes torque variation zero control for controlling a current vector of the AC motor 14 so that the deviation between a first estimated torque, obtained from a motor detection current vector of the AC motor 14 and a second estimated torque, obtained from a command current vector for torque control becomes substantially zero, thereby preventing unpleasant torque variations in the transition of the input power control of the MG unit 30.例文帳に追加
更に、交流モータ14のモータ検出電流ベクトルから求めた第1の推定トルクとトルク制御用の指令電流ベクトルから求めた第2の推定トルクとの偏差が略ゼロとなるように交流モータ14の電流ベクトルを制御するトルク変動ゼロ制御を実行することで、MGユニット30の入力電力制御の過渡時に不快なトルク変動を防止する。 - 特許庁
Furthermore, it executes torque ripple zero control to correct the phase of the rectangular wave voltage so that the deviation between first estimated torque obtained from a detected current vector for torque control of the AC motor 14 and the second estimated torque obtained from a motor detected current vector may be almost zero, whereby it prevents uncomfortable torque ripple at transition of input power control of the MG unit 30.例文帳に追加
更に、交流モータ14のトルク制御用の検出電流ベクトルから求めた第1の推定トルクとモータ検出電流ベクトルから求めた第2の推定トルクとの偏差が略ゼロとなるように矩形波電圧の位相を補正するトルク変動ゼロ制御を実行することで、MGユニット30の入力電力制御の過渡時に不快なトルク変動を防止する。 - 特許庁
A cycle decision part TC measures the cycle of zero-phase voltage V0 after the removal of a fault from a digital filter DF and an inhibiting part INH locks the output of the directional ground fault from a phase comparison part PC by the period, when the measured cycle is different from the base wave cycle of a distribution system.例文帳に追加
周期判定部TCは、ディジタルフィルタDFからの事故除去後の零相電圧V_0の周期を計測し、この周期が配電系統の基本波周期と異なる期間だけ位相比較部PCからの方向地絡事故検出出力を抑止部INHでロックする。 - 特許庁
In this plurality of dot indicators 91 to 919, each luminous color is different in dot indicators 91 to 94 corresponding from zero seconds to one minute, dot indicators 95 to 98 corresponding from one minute 30 seconds to five minutes, and dot indicators 99 to 919 corresponding from five minutes to fifteen minutes.例文帳に追加
これら複数個のドット表示器91〜919は、「0秒」〜「1分」に対応するドット表示器91〜94と、「1分30秒」〜「5分」に対応するドット表示器95〜98と、「5分」〜「15分」に対応するドット表示器99〜919ではそれぞれ発光色が異なる。 - 特許庁
Furthermore, when a normal revolution from the engine 5 and reverse revolution from the hydraulic motor 501 coincides in such an output control condition that an output from the hydraulic motor 501 is reverse, the working vehicle is configured so that a moving speed of the running machine 2 may become zero.例文帳に追加
前記油圧モータ501からの出力が逆転方向の出力制御状態で前記エンジン5からの正転回転数と前記油圧モータ501からの逆転回転数とが一致する場合に、前記走行機体2の移動速度が零になるように構成する。 - 特許庁
When a negative voltage is inputted from the alternating-current power supply 301, and on-signal is outputted to the transistor 309 for a fixed period of time by using a time-point after the lapse of a fixed period from a trailing edge (a changing point from on to off) of the zero-crossing signal as a reference, thereby supplying power to the ceramic heater 303.例文帳に追加
一方、交流電源301から負電圧が入力される時、ゼロクロス信号の立ち下がりエッジ(オンからオフに変化するポイント)から時間Tcが経過した後を基準に、トランジスタ309に所定期間、オン信号を出力してセラミックヒータ303に電力を供給する。 - 特許庁
When actuation of a brake pedal is expected after the degree of actuation of an accelerator is decreased from a predetermined value to zero, the closing of a throttle valve is controlled with such a condition that brake negative pressure is being off, toward the atmospheric pressure side, from an expected demand value which is off from a demand value required for driving a brake booster 50, toward a vacuum side.例文帳に追加
アクセル踏込量が所定値から「0」になってブレーキ踏込が予測されたとき、ブレーキ負圧がブレーキブースタ50を駆動するのに必要な要求値よりも真空側の値である予測要求値より大気圧側の値であることを条件に、スロットルバルブ23の閉じ制御が実行される。 - 特許庁
A direction detection signal generating circuit 9 does not intermittently detect the velocity in the track jump through the counting of the number of track zero-cross pulses from the sub-beam but generates a direction detection signal that is deviated by 90 degrees in phase from the main push-pull signal from a main push-pull signal generating circuit 10.例文帳に追加
方向検出信号生成回路9はサブビームから、トラックジャンプ中の速度検出をトラックゼロクロスパルス数をカウントして求める断続的な検出でなく、メインプッシュプル信号生成回路10からのメインプッシュプル信号と位相が90°ずれた方向検出信号を生成する。 - 特許庁
Swing preventive operation time and a swing preventive operation quantity are determined on the basis of the amplitude, and after a prescribed time passes further from a half-period passing time from the time of the swing angle zero, the swing preventive operation quantity is impressed on the crane during the swing preventive operation time.例文帳に追加
振幅に基づいて振れ止め操作時間及び振れ止め操作量が決定され、振れ角零の時点から半周期経過時からさらに所定時間経過後に振れ止め操作時間の間振れ止め操作量がクレーンに印加される。 - 特許庁
A lens moving amount equivalent to the range of a distance to reach the shortest photographing distance Dvmin+α of the photographing lens from the position where the Dv' value is changed from one to zero is obtained, so that the number of pulses corresponding to the moving amount obtained is set as the specified number Pn.例文帳に追加
Dv’が1→0に変化した位置から、撮影レンズの最短撮影距離Dvmin+αに至る距離の範囲に相当するレンズ移動量が求められ、該求められた移動量に対応するパルス数が所定数Pnとされる。 - 特許庁
A CPU 10 measures a bioelectric impedance from the current Ib and the voltage Vp thus detected to calculate electric admittances Y (0) and Y (∞) of the subject at zero of frequency and at the infinity of frequency from the bioelectric impedance measured.例文帳に追加
CPU10は、検出された電流Ibと電圧Vpとに基づいて、生体電気インピーダンスを測定し、測定された生体電気インピーダンスに基づいて、周波数0時及び周波数無限大時の被験者の電気アドミッタンスY(0),Y(∞)を算出する。 - 特許庁
Exist light from a semiconductor laser 1 is divided into three rays of light of zero-order light being a main beam and ±1st-order diffracted rays being sub beams by a diffraction optical element 3, and a focus error signal is detected from each of the main beam and the sub beams.例文帳に追加
半導体レーザ1からの出射光を回折光学素子3によりメインビームである0次光、サブビームである±1次回折光の3つの光にそれぞれ分割し、メインビームとサブビームのそれぞれからフォーカス誤差信号を検出する。 - 特許庁
A line-introducing hole 21 is opened on a butt section 1 at a part separated from the tip side of the butt section by a definite distance X and the part X from the line-introducing hole 21 to the tip section has the form of zero taper or extremely slow taper (0 to 1/1000).例文帳に追加
釣糸導入孔21を元竿1の穂先側先端から一定の距離Xを隔てて形成し、釣糸導入孔21より穂先側の部分Xは0テーパ又は超スローテーパ(0以上1000分の1以下)に形成する。 - 特許庁
After a service person dispatched from a service center performs the maintenance, he operates switches 42 to 46 according to specified patterns to produce a reset signal so as to cancel the storage time of an nonvolatile storage part and counting is re-started from zero.例文帳に追加
サービスセンターから派遣されたサービスマンがメンテナンスを行った後、スイッチ42〜46を特定パターンに従って操作することによってリセット信号が生じて不揮発性記憶部の記憶時間がキャンセルされ、再度0から計時が再開する。 - 特許庁
A rate of increase in current until the electric current passed through the wide-gap semiconductor element reaches I1 from zero is a constant value dI1/dt and a rate of increase in current until the electric current passed through the wide-gap semiconductor element reaches the rated current from I1 is dIn/dt.例文帳に追加
上記ワイドギャップ半導体素子内の積層欠陥の発生による上記ワイドギャップ半導体素子の破壊を防止するように、上記dI1/dtは、一定値で、かつ0.5秒<(I1÷(dI1/dt))なる関係式を満たす。 - 特許庁
Hereby, since contact areas of the bracket 7 with the guide pipe 9 and the body 12 are extremely small, vibration energy transmitted from the bracket 7 to the guide pipe 9 and the body 12 at the oscillation time from an ultrasonic sensor 3 is extremely small or zero.例文帳に追加
このため、ブラケット7とガイドパイプ9およびボディ12との接触面積は極小さくなっているので、超音波センサ3が発振した際にブラケット7からガイドパイプ9およびボディ12に伝達される振動エネルギは極わずかあるいは0となる。 - 特許庁
In controlling power to a ceramic heater 303, when a positive voltage is inputted from an alternating-current power supply 301, an on-signal is outputted to a transistor 309 for a fixed period of time by using a leading edge (a changing point from off to on) of a zero-crossing signal as a reference.例文帳に追加
セラミックヒータ303への通電制御は、交流電源301から正電圧が入力される時、ゼロクロス信号の立ち上がりエッジ(オフからオンに変化するポイント)を基準に、トランジスタ309に所定期間、オン信号を出力する。 - 特許庁
A sensitivity dead zone characteristic transmitter 8 issues a value of zero when a command value from a comparator 7 is within a predetermined range and a command value based on a predetermined sensitivity dead zone characteristic curve when a command value from a comparator 7 is outside the predetermined range.例文帳に追加
感度不感帯特性発生器8は、比較器7からの指令値が所定の範囲内であるときは零を出力し、所定の範囲外であるときは予め定めた感度不感帯特性曲線に基づいて指令値を出力する。 - 特許庁
A controller computer changes an input current value for a coil of a capacity control valve from zero to a target input current value a3, by a predetermined time T, according to a cooling load in shifting from the acceleration cut control to the normal one.例文帳に追加
制御コンピュータは、加速カット制御から通常時制御へ移行する際、容量制御弁のコイルに対する入力電流値を、ゼロから冷房負荷に応じた入力電流値目標a3にまで所定時間Tかけて変更する。 - 特許庁
A CCD camera 8 photographs a nozzle 7 from the cross direction and a controller 4 into which an image is introduced from the CCD camera 8, detects dislocation amount of the tip of the nozzle 7 and controls an X-Y-Z moving mechanism 5 so that the dislocation amount becomes zero.例文帳に追加
CCDカメラ8は、ノズル7を横方向から撮像し、このCCDカメラ8からの画像を導入した制御器4は、ノズル7先端Qの位置ずれ量を検出し、これらが零となるようにX−Y−Z移動機構5を制御する。 - 特許庁
The background film area is converted into a partial distance image where height from a reference plane is zero, and the two-dimensional skin area and the other area are converted into partial distance images by converting luminance into height from the reference plane by a prescribed operation method.例文帳に追加
背景幕領域は基準面からの高さが0の部分距離画像に変換され、2次元肌領域およびその他の領域は所定の演算方法にて輝度を基準面からの高さに変換することにより部分距離画像に変換される。 - 特許庁
Time information from voltage zero cross to turn-on of a triac 14 is stored in a storage circuit 17s, and a control circuit 18 reads the information for the time corresponding to the power saving rate from the storage circuit 17 and controls a conduction timing for the triac 14.例文帳に追加
記憶回路17に電圧ゼロクロスからトライアック14がターンオンするまでの時間情報を記憶し、制御回路18が節電率に応じた時間情報を記憶回路17から読み出して、トライアック14の導通タイミングを制御する。 - 特許庁
To provide a packing for pilfer-proof cap, which can prevent an LB zero touch from occurring even when bottles are kept at a low temperature (e.g. 4-5°C), and in addition, can prevent an air leakage in the bottle due to a doming phenomenon of the cap main body from occurring.例文帳に追加
瓶類が低温(例えば4〜5°C)で保管された場合でも、LBゼロタッチを防止でき、更には、キャップ本体のドーミング現象に起因する瓶内部の気密漏れを防止できるようにしたピルファープルーフキャップ用のパッキンを提供する。 - 特許庁
When regulating the groove direction of the diffraction grating 16, a strip-shaped diffraction light from the diffraction grating 16 obtained by making a zero-order diffraction light from the diffraction grating spectroscope 12 incident on the diffraction grating 16, is made incident on the target member 22.例文帳に追加
回折格子16の溝方向を調整するときは、回折格子分光器12からの0次回折光を回折格子16に入射することにより得られる前記回折格子16からの帯状の回折光を的部材22に入射させる。 - 特許庁
(a) the amount determined by the Member Commodity Exchanges Dissolved in an Incorporation-Type Merger pursuant to the provisions of the Incorporation-Type Merger contract (limited to an amount of zero or greater) within the scope of the amount of the net assets subject to the Incorporation Type Merger (which means the amount calculated by deducting the value placed on the Property subject to the Incorporation-Type Merger [limited to liabilities] from the value placed on the Property subject to the Incorporation-Type Merger [limited to assets] (limited to those inherited from a Member Commodity Exchange acquired through an Incorporation-Type Merger); hereinafter the same shall apply in this paragraph; and in the case such amount is less than zero, the amount shall be zero); 例文帳に追加
イ 新設合併対象純資産額(新設合併対象財産(資産に限る。)に付すべき価額から 新設合併対象財産(負債に限る。)に付すべき価額を減じて得た額(新設合併取得 会員商品取引所から承継するものに係るものに限る。)をいう。以下この項におい て同じ。)(当該額が零未満である場合にあっては、零)の範囲内で、新設合併消滅 会員商品取引所が新設合併契約の定めに従い定めた額(零以上の額に限る。) - 経済産業省
Peripheral speed in which the total amount of vector of X-direction and Y- direction of rotational force working on the glass plate G from the multiple concentric circle surface plate 12 approaches zero is set for every surface plate 26, 28 and 30.例文帳に追加
そして、多重同心円定盤12からガラス板Gに働く回転力のX方向及びY方向のベクトルの総和が零に近づくような周速を定盤26、28、30毎に設定する。 - 特許庁
Also, the counter 49 starts counting by decrementing it, and when the count value is turned into '0(zero)', the motor 41 and the AC power source 45 are electrically interrupted according to a signal from the counter 49, and the motor 41 stops.例文帳に追加
また、カウンタ49も同時にデクリメントでカウントを開始し、カウント値が“0(ゼロ)”になると、カウンタ49からの信号によりモータ41と交流電源45は電気的に遮断され、モータ41が停止する。 - 特許庁
A plurality of dilution holes 32 is formed inside the duct body, and is installed in an (X, Y, Z)coordinate position measured from a zero reference point in the center of an outlet plane of the transition piece.例文帳に追加
複数の希釈孔(32)が、ダクト本体内に形成され、かつトランジションピースの出口平面の中心におけるゼロ基準点から測定した選択X、Y及びZ座標位置に設置される。 - 特許庁
The counter force setting means sets the force calculated from the acceleration to reduce the first speed to zero in the unit time in the counter force when the calculated first speed is a predetermined speed or less.例文帳に追加
反対力設定手段は、算出した第1速度が所定速度以下のときに、第1速度を単位時間でゼロに減じる加速度から計算する力を、反対力に設定することを特徴とする。 - 特許庁
When the sample number is less than a reference value, an output signal from an averaging circuit 114 is given to an integration circuit 116, or when the sample number is more than the reference value, a 'zero' value is given to the integration circuit 116 respectively.例文帳に追加
サンプル数が基準値よりも小さい場合には、平均化回路114の出力信号を、サンプル数が基準値よりも大きい場合には、ゼロ値を、それぞれ積分回路116に入力する。 - 特許庁
To reduce part tray exchange time and to reduce the stop time of a part-fitting operation then or set the time to zero, when withdrawing parts from a plurality of piled up part trays and fitting the parts to a substrate.例文帳に追加
複数枚段積みした部品トレイから部品を取り出し、基板に装着するとき、部品トレイ交換時間を短縮し、且つ、その際における部品装着動作の停止時間を零又は短縮する。 - 特許庁
To provide an apparatus for removing water by which water can be removed from a gas while saving an installation space thereof even when the apparatus for removing water is installed in a zero-gravity or microgravity space and to provide a fuel cell power generation system utilizing the apparatus for removing water.例文帳に追加
無重力空間や微小重力空間であっても、ガスから水を取り除くことが省スペースでできる除水装置及びこれを利用する燃料電池発電システムを提供する。 - 特許庁
The sum total of the loads β_1 and β_2 from (pads of) respective calipers 17 and 17 charged on a rotor 15, namely vectors β_1 and β_2 of the tangential force of the braking force, is set zero with respect to the circumference direction of the rotor 15.例文帳に追加
ロータ15に加わる、各キャリパ17、17(のパッド)からの荷重β_1、β_2、即ち、制動力の接線力のベクトルβ_1、β_2の総和を、このロータ15の円周方向に関して0にする。 - 特許庁
In order to align tilt of an MPP signal and an SPP signal acquired from a detection signal for a photodetector, an invariant point A of lens shift quantity, where a DC component for the SPP signal becomes zero, is acquired first.例文帳に追加
フォトディテクタの検出信号から得られるMPP信号とSPP信号の傾きを揃えるために、まず、SPP信号のDC成分がゼロとなるレンズシフト量の不変点Aが求められる。 - 特許庁
In an end part of laser beam welding of a working piece 8 by laser beam 3, velocity of feeding a filler supplied to a focus position of the laser beam 3 from a torch 12 is gradually decreased to zero.例文帳に追加
加工ワーク8の、レーザ光3によるレーザ溶接の終端部において、トーチ12からレーザ光3の焦点位置に供給されるフィラー送給速度を徐々に減少して零とする。 - 特許庁
Accordingly, by getting to start conduction consecutively from the circuit, out of the bidirectional conductive circuits 11-13, of which the voltage between both ends is nearly zero, the snow melting device 1 can be started without generation of noise.例文帳に追加
従って、各双方導通回路11〜13のうち、両端の電圧が略ゼロボルトになったものから順次導通させると、ノイズを発生することなく融雪装置1を起動することができる。 - 特許庁
To provide the controller of a plant capable of maintaining satisfactory control performance by preventing the identification error of a model parameter from being increased when a controller output is set so as to be a value around zero.例文帳に追加
コントローラ出力がゼロ近傍の値をとる場合に、モデルパラメータの同定誤差が増加することを防止し、良好な制御性能を維持することができるプラントの制御装置を提供する。 - 特許庁
In this manufacturing device, jointing while moving the joint part so that a relative speed difference to a conveying speed of a workpiece W approaches to zero is repeated multiple times from the front end in the conveying direction.例文帳に追加
この製造装置では、ワークWの搬送速度との相対速度差がゼロに近づくように接合部を移動させながら行う接合を搬送方向の前端側から複数回繰り返して行う。 - 特許庁
When the boosting circuit 40 does not have the sufficient output, the target charging and discharging electric current is set to be zero, and power is supplied from the sub-power supply device 50 only for a shortfall amount of performance of the boosting circuit 40.例文帳に追加
昇圧回路40の出力に余裕がなければ、目標充放電電流をゼロに設定して、昇圧回路40の能力不足分だけ副電源装置50から電源供給する。 - 特許庁
A first memory control unit 10e decreases the time-out value of the communication data in the second memory 10d at the interval of prescribed time and erases the communication data, with which the time-out value becomes zero, from the second memory 10d.例文帳に追加
第1のメモリ制御装置10eは,第2のメモリ10dの通信データのタイムアウト値を所定の時間ごとに減じ,ゼロとなった通信データを第2のメモリ10dから消去する。 - 特許庁
Since a supply source of the exciting current is switched from the DC power supply line 9 to the power generator 1 when the current flowing in the isolator 12 becomes almost zero, complicated control is unnecessary at the time of starting.例文帳に追加
断路器12を流れる電流がほぼ零になったときに励磁電流の供給元を直流電源線9側から発電機1側に切り替えるので、起動時に複雑な制御が不要である。 - 特許庁
| 例文 |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|