「width」に関連した英語例文の一覧と使い方(885ページ目) - Weblio英語例文検索

In the surface acoustic wave device provided with an IDT electrode to stimulate a surface acoustic wave of an SH type on a piezoelectric substrate capable of stimulating the SH type surface acoustic wave, a cross width W of electrode fingers of the IST electrode is selected to be within a range of 20-140λ.例文帳に追加

ＳＨタイプの表面波を励振可能な圧電基板上にその表面波を励振すべくＩＤＴ電極を備えた弾性表面波デバイスにおいて、上記ＩＤＴ電極の電極指の交差幅Ｗを、２０λ〜１４０λの範囲にする。 - 特許庁

The axle detector has three liquid-pressure sensor units 1 to 3 placed in a channel base 4 buried in a road to the road width determined by curbstones and a pressure plate 5 is pressed against and fixed to the channel base 4 with a fixture, e.g. a bolt 6.例文帳に追加

車軸検知器は、道路縁石によって囲まれた道路幅員に亙って路面に埋設されたチャネルベース４内に３つの流体圧センサユニット１〜３が置かれており、押さえ板５を固定具、例えばボルト６によってチャネルベース４に押さえつけて固定する。 - 特許庁

A crankshaft is rotated to the normal rotation side in the initial stage of the rotation start of the crankshaft by driving a motor generator(M/G), and when the rotation of the crankshaft is stopped by the normal rotation, reverse rotation is carried out by a portion of preset reverse rotation angular width (80°) (S810-S860).例文帳に追加

モータジェネレータ（Ｍ／Ｇ）の駆動によりクランク軸の回転開始時当初にクランク軸を正転側に回転させ、この正転によってクランク軸の回転が停止した場合には、予め設定した逆転角度幅（８０°）分の逆転を行う（Ｓ８１０〜Ｓ８６０）。 - 特許庁

And also, in a second lighting mode, the specific light chip 12aB placed at the center, and two general light-emitting chips 12aD, 12aE arranged in series of its backward side, are simultaneously lit, so that a landscape light distribution pattern with a wide width of its upper and bottom parts is formed.例文帳に追加

また、第２の点灯モードでは、中央に位置する特定発光チップ１２ａＢとその後方側に直列に配置された２つの一般発光チップ１２ａＤ、１２ａＥを同時点灯させ、これにより上下幅が広い横長の配光パターンを形成する。 - 特許庁

On a sliding face 11, soft magnetic films 13a and 13b which hold a magnetic gap g therebetween and substrates 14a and 14b are mechanically worked linearly along a slide direction of a magnetic tape and a track end working grooves defining a track width Tw of the magnetic gap g are formed.例文帳に追加

摺動面１１において、磁気ギャップｇを挟む軟磁性膜１３ａ、１３ｂ及び基体１４ａ、１４ｂが磁気テープの摺動方向に沿って直線状に機械加工され磁気ギャップｇのトラック幅Ｔｗを規定するトラック端加工溝が形成されている。 - 特許庁

A saw blade 70 arranged on the outside in width direction of the clipper blade 10, extending to the front side along the clipper blade 10 and turning the tip of the blade to the outside is detachably attached to the lower blade 21 and a cover member 80 is detachably attached to the clipper blade 10.例文帳に追加

下刃２１にはバリカン刃１０の幅方向外側に配置されてバリカン刃１０に沿って前側へ延びて刃先が外側へ向いたノコギリ刃７０が着脱自在に取り付けられ、バリカン刃１０にはカバー部材８０が着脱自在に装着される。 - 特許庁

Preferably, the adhesive has an average optical transmission factor of not less than 70% in a wave length range of 450 nm-800 nm, and a variation width of the optical transmission factor in the wave length range of 450 nm-800 nm is within ±10% of the average optical transmission factor.例文帳に追加

樹脂接着剤は４５０ｎｍ〜８００ｎｍの波長領域で平均７０％以上の光透過率を有しかつ４５０ｎｍ〜８００ｎｍの波長領域で光透過率の変動幅が平均の光透過率の±１０％以内であることが好ましい。 - 特許庁

It is desirable that the net receiving part 2 is substantially U-shaped so that the width of the opening part is smaller than that of the inmost part, one end of the bar material is bent to form the fixing nail part 3, and the other end thereof is bent to open the upper side thereof with the tip thereof curved to project upward.例文帳に追加

ネット受け部２を、開口部の幅が奥部の幅より狭い略Ｕ字形とし、棒材の一端を折り曲げて固定釘部３を形成すると共に、他端を上方が開口するように折り曲げてその先端部を上方突に湾曲させることが望ましい。 - 特許庁

To provide a conductive roller for an electro-photographic device used as a developing roller or a transcribing roller or a charging roller to be excellent in stability of electric resistance to eliminate process unstability of bonding agent application unevenness, width dimension, etc., generating a problem in an existing line.例文帳に追加

現像ロ−ラ又は転写ロ−ラもしくは帯電ロ−ラとして使用される、電気抵抗の安定性に優れ、現行ラインで問題となる接着剤塗布ムラや巾寸法等の工程不安定性を無くした電子写真装置用の導電性ロ−ラの提供。 - 特許庁

An upper pin 31 of the upper door-side member fixed to the upper part in the width directional one side of the door and a coil spring 34 upward energizing it are surrounded with an approximately cylindrical side wall cover 32, and a lower face cover 38 closing the lower end opening of the side wall cover is provided.例文帳に追加

扉の幅方向一側の上部に固定される上部扉側部材の上部ピン３１と、これを上向きに付勢するコイルばね３４とが略筒状の側壁カバー３２に包囲され、側壁カバーの下端開口を塞ぐ下面カバー３８が設けられる。 - 特許庁

An engine 20 is mounted in a car body, the crankshaft is turned in the width direction of the car body 1, the cylinder 26 of the engine is inclined to the direction of the center of the gravity of the car body 1, and an air supply/discharge device 60 located in front of the car body 1 is connected with the engine 20.例文帳に追加

車体１にエンジン２０を搭載してそのクランクシャフトを車体１の幅方向に向け、エンジン２０のシリンダ２６を車体１の重心方向に傾斜させ、エンジン２０に、車体１の前方に位置する給排気装置６０を接続する。 - 特許庁

A lower body work of a vehicle according to this invention is equipped with a bumper facia 5, a sub-frame having a cross-member 62 extending across the vehicle width directly behind a radiator 22, and a front under-cover 10a covering the area between the bottom of the bumper facia 5 and the undersurface of the cross-member 62.例文帳に追加

本発明に係る車体下部構造は、バンパフェイシャ５と、ラジエタ２２直後で車幅方向に延在するクロスメンバ６２を有するサブフレームと、バンパフェイシャ５の下端部とクロスメンバ６２の下面部との間を覆う前部アンダカバー１０ａとを備える。 - 特許庁

To provide rolled paper capable of preventing aging loosening of winding of the paper of a paper material having high rigidity such as not only a thin paper material but also a paper material having a large width or thickness, an ink jet recording sheet or the like and preventing conveying of a foreign matter to a conveying unit of a recording equipment.例文帳に追加

薄手の紙材のみならず、幅や厚さの大きい紙材やインクジェット記録用紙等の剛性の高い紙材に対しても経時的にロール紙の巻きが緩むのを防止でき、かつ記録機器の搬送部への異物搬送を防止できるロール紙を提供する。 - 特許庁

In this apparatus 1, carrier films A1 and A2 are fed by motors 25 and 45 while wound and the cueing of the overcoat films P1 and P2 is performed by detecting the cueing marks M, which are provided to the carrier films A1 and A2 and have a definite width in the feed directions of them, by cueing sensors 21 and 41.例文帳に追加

この装置１では、モータ２５，４５でキャリアフィルムＡ１，Ａ２を巻取りながら搬送し、搬送方向に一定幅を有する頭出しマークＭを、頭出し用センサ２１，４１で検出することにより、オーバコートフィルムＰ１，Ｐ２の頭出しを行う。 - 特許庁

To provide a method for producing an Fe-Ni based alloy thin sheet which can solve the problem of heat shrinkage in particular, can realize excellent flatness even in the case of a wide width of 60 mm or more for example, and is used as a material for a lead frame and a material for a lead.例文帳に追加

特に加熱収縮の問題を解決でき、例えば６０ｍｍ以上の広い幅であっても優れた平坦性を実現できるリードフレーム用素材やリード用素材等に用いられるＦｅ−Ｎｉ系合金薄板条の製造方法を提供する。 - 特許庁

The positioning members 39 are arranged such that edges of contact portions 39a on the width-direction center side in contact with the fixing member 21 are positioned outside an image area L2 and inside a paper-passing area L1 for a recording medium of a maximum passing-capable size.例文帳に追加

位置決め部材３９は、定着部材２１に当接する当接部３９ａの幅方向中央部側の端部の位置が、通紙可能な最大の記録媒体の通紙領域Ｌ１の内側であって画像領域Ｌ２の外側になるように配設される。 - 特許庁

The nozzle 20 has a base portion forming a flat molten metal passage by closing four sides, and a pair of guide portions which extend from the base portion, and close both ends of the molten metal in the width direction after passing through the base portion by being brought into sliding contact with a pair of the cooling rolling roller.例文帳に追加

ノズル２０は、四方を閉塞して扁平な溶湯通路を形成している基部と、基部から延出するとともに一対の冷却圧延ローラに摺接することによって基部を通過した溶湯の幅方向の両端を閉塞する一対の案内部を有している。 - 特許庁

Since the heating process is conducted at the same time as the winding of the coil wire 13 in a state that the connecting part is pressed at a wide-width flat part, the connecting part can be fixed in a state of being kept in the favorable degree of adhesion and at a favorable connecting angle.例文帳に追加

コイル線材１３の巻回と同時に幅広の扁平部分で有効に連結部分が押圧された状態で加熱工程が行われるため、良好な密着度および連結角度に維持された状態で連結部分を固定することができる。 - 特許庁

The leakproof wall 7 has a plurality of highly rigid parts 6c where rigidity of a part of a flexible sheet 6 is increased in an area (X3 area) on the width direction center side of the sanitary napkin 1 from the peak part 7a of the leakproof wall 7, which is at least the excretion part area (a).例文帳に追加

防漏壁７は、少なくとも排泄部領域ａであって、防漏壁７の頂部７ａより生理用ナプキン１の幅方向中央側の領域（Ｘ３領域）に伸縮性シート６の一部の剛性を高めた高剛性部６ｃを複数有している。 - 特許庁

To provide a frame capable of covering a disadvantage, because the disadvantage of getting weak in strength exists in a frame constituted to remove a width-directional member to introduce easily peripheral equipment or the like into a space part for the purpose of introducing the peripheral equipment into the space part of the frame of an injection molding machine.例文帳に追加

射出成形機フレーム空間部に周辺機器を納めるため、幅方向部材を取り払い、周辺機器等が容易に同空間部に納入できるようにしたフレームは強度的に弱いという欠点があり、この欠点を補うフレームを提供する。 - 特許庁

In a slicer for slicing the portion of food placed on the placing table 1 which protrudes from a blade receiving frame, by relatively moving the placing table 1 and a band knife 9, the partition 13 to divide the blade receiving frame in the width direction for small pieces of food is detachably disposed on the blade receiving frame.例文帳に追加

載置台１に載置された食品の受刃枠から突出した部分を載置台１とバンドナイフ９とを相対移動させてスライスするスライサーにおいて小さい食品用に受刃枠を巾方向に仕切る隔壁１３を受刃枠に着脱可能に設置する。 - 特許庁

A width of a plate 3 is smaller than an outer diameter of the unit cell 2, and the plate 3 is provided with openings 13 at portions in correspondence with outer terminals of the unit cells 2, and a plate-like metal bus bar for connecting the unit cells is insertion-molded so as to choke up the openings 13.例文帳に追加

プレート３の幅は単電池２の外径より小さく、プレート３には単電池２の外部端子に対応する箇所に開口１３が形成されており、開口１３を塞ぐように単電池２を接続する板状の金属ブスバがインサート成形されている。 - 特許庁

The piezoelectric transducer has a thickness T (μm) of a piezoelectric ceramic layer 22 in the piezoelectric actuator 2 and the maximum width W (mm) of a substrate 1 in the cavity 11 of the substrate 1 in a planar direction, set to ranges which satisfy a formula (1): T≥(19.6W+5.5)×10^-3.例文帳に追加

圧電アクチュエータ２中の圧電セラミック層２２の厚みＴ（μｍ）と、基板１のキャビティ１１の、当該基板１の面方向の最大幅Ｗ（ｍｍ）とを式（１）：Ｔ≧（１９．６Ｗ＋５．５）×１０^−３ （１）を満足する範囲とした圧電変換装置である。 - 特許庁

A cut-out part 23 opened frontward from the root position of the lance 20 is formed and a release operation piece 24 connected to the side face of the lance 20 to the extent as much as half the width of the cut-out part 23 is projected on a barrier rib 22 between each adjacent pair of the cavities 19.例文帳に追加

隣り合うキャビティ１９間の隔壁２２には、ランス２０の根元位置から前方へ開放する切欠部２３が設けられていて、この切欠部２３の幅寸法の半分程度までランス２０の側面に連結された解除操作片２４が突設されている。 - 特許庁

The luminescence region 45 of the organic EL elements constituting the array of the organic EL elements 40, is characteristic in that the width M of each luminescent element in the direction where the elements are arrayed, is not less than 2.5 times the film thickness of an interlayer insulation layer, and not more than 83% of the array pitch P of the elements.例文帳に追加

有機ＥＬ素子アレイ４０を構成する有機ＥＬ素子の発光領域４５について、発光素子が並ぶ方向における幅Ｍを、層間絶縁層の膜厚の２．５倍以上であり、かつ、発光素子の配列ピッチＰの８３％以下とする。 - 特許庁

On the way of a conveying route 10 for conveying a steel sheet 1 a prescribed portion of which in the width direction is thin steel sheet part 2 and whose rest part is formed as a thick steel plate 3A in the length direction, the steel sheet is taken out after heating the whole while conveying the steel sheet in the length direction.例文帳に追加

幅方向において所定部分が薄肉鋼板部２で残部が厚肉鋼板部3Aとして形成した鋼板１を長さ方向に搬送する搬送経路10中において、鋼板を長さ方向に搬送しながら、全体加熱して取り出す。 - 特許庁

This handrail frame for the prefabricated scaffolding is provided with a plurality of pairs of hourglass-shaped guide rollers 4 liftable along a post C of a standard B while holding the post C to cover it from both lateral sides, at the center part in the width direction of the handrail frames 1, 1' at prescribed spaces in a vertical direction.例文帳に追加

手摺枠１、１´の幅方向の中央部には、建枠Ｂの脚柱Ｃを左右両側より覆うように挟持して脚柱Ｃに沿って昇降自在とする一対の鼓形のガイドローラ４を、上下方向に所定間隔をおいて複数組備える。 - 特許庁

Light emitted to the vicinity of a boundary of the exposure region is blocked by moving, in accordance with the exposure region, a second shutter group 30a, 30b, 40a, 40b having a width smaller than that of the first shutter group 10, 20, and arranged nearer to the mask 4 than the first shutter group 10, 20.例文帳に追加

第１のシャッター群１０，２０よりも幅が小さく、第１のシャッター群１０，２０よりもマスク４に近接して設けた第２のシャッター群３０ａ，３０ｂ，４０ａ，４０ｂを、露光領域に応じて移動して、露光領域の境界付近へ照射される光を遮断する。 - 特許庁

To provide a die device for pressing a work of a metal plate bending machine with which the minimum width dimension at which a metal plate can be clamped is made smaller as compared with that by a conventional method, the improvement of rigidity is expectable with simple structure and the bending of a thicker metal plate is realized.例文帳に追加

板材のクランプ可能最小幅寸法が従来に比較して、より小さく出来、簡単な構造により剛性向上が期待出来、より、厚肉の板材の曲げ加工が出来る板材曲げ加工機のワーク押え金型装置の提供を目的とする。 - 特許庁

An engaging groove 6 is formed in the door stop member 3 in a longitudinal direction of the same, and a slit 7 which is narrower in width than the engaging groove 6 is formed between the engaging groove 6 and a door stop surface 4 of the door stop member 3, in a manner communicating with both the groove 6 and the surface 4.例文帳に追加

戸当たり部材３に戸当たり部材３の長手方向に係止溝６を設けると共に係止溝６と戸当たり部材３の戸当たり面４との間に係止溝６より幅の狭いスリット７をこれらの間を連通させるように設ける。 - 特許庁

When the outer periphery surface of the drum is electrified through the shield cover 26, charge is applied only to a range on both ends in the axial direction of the outer periphery surface where the paper is electrostaticly attracted and only both ends in the direction of the width of the paper are electrostaticly attracted to the outer periphery surface.例文帳に追加

このシールドカバー２６を介してドラムの外周面を帯電させると、用紙が静電吸着する外周面上の軸方向両端の領域だけに電荷が付与され、用紙の幅方向両端だけが外周面に静電吸着される。 - 特許庁

To provide a coupling member for a door hanger, which makes a dancing phenomenon during the traveling of a door inhibited by enabling a roller part to be attached to the width end of the door when the roller part of the door hanger attached to the door is engagedly fitted for hanging from a rail part of an automatic door device in a freely travelable manner.例文帳に追加

自動ドア装置のレール部に、ドアに取着したドアハンガーのローラ部を走行自在に係嵌吊下する際、ドアの幅長端部寄りにローラ部の取着を可能として、ドア走行時の踊り現象が阻止されるドアハンガー用連結部材を提供する。 - 特許庁

A peripheral frame is formed so as to surround a display area where pixels are formed, a liquid crystal composition is held in the internal part of the peripheral frame, the outside of the peripheral frame is filled with a sealing material in the same width and a driving circuit forming area is provided at the inside of the peripheral frame.例文帳に追加

画素が形成される表示領域を囲むように周辺枠を形成し、周辺枠内部に液晶組成物を保持し、周辺枠外側に等しい幅でシール材を充填し、周辺枠内側には駆動回路形成領域を設ける。 - 特許庁

The method for producing the carbon fiber comprises the following process: After a precursor fiber is formed from the thermoplastic carbon precursor, the precursor fiber is heat-treated to form a stabilized precursor fiber, which is then baked so as to result in that the spectrum line width of the electron spin resonance of the baked fiber decrease at least once and then increase.例文帳に追加

熱可塑性炭素前駆体から前駆体繊維を形成した後、熱処理して安定化前駆体繊維を形成し、ついで安定化前駆体繊維の焼成で、電子スピン共鳴のスペクトル線幅が少なくとも一回は減少して増加させる。 - 特許庁

Thus, the axial thermal expansion amount of the sleeve portion exceeds the axial thermal expansion amount of the shaft member during high temperatures to reduce the gap width of a thrust bearing gap, suppressing the lowering of bearing rigidity in the thrusting direction during the high temperatures.例文帳に追加

これにより、高温時には、スリーブ部の軸方向熱膨張量が軸部材の軸方向熱膨張量を上回ることにより、スラスト軸受隙間の隙間幅が小さくなり、高温時におけるスラスト方向の軸受剛性の低下を抑制することが可能となる。 - 特許庁

Rotation/non-rotation as to whether or not rotation processing is applied to received image information is automatically decided on the basis of image data width information and a recording paper size of a paper feed cassette, and when the rotation is decided, memory reception is selected and when the non-rotation is selected, direct reception is selected.例文帳に追加

画データ幅情報と存在する給紙カセットの記録紙サイズとによって、受信画情報の回転処理を行うか行わないかの回転／非回転を自動的に判断し、回転の場合にはメモリ受信を行い、非回転の場合は直接受信を行う。 - 特許庁

Thus, the space S is demarcated in the area 1 at a region on the lower side in the vertical direction of the vehicle and on the central side in the vehicle width direction relative to the air conditioning unit 5, and an instrument with a function other than the air conditioning function is arranged in this space S.例文帳に追加

これにより領域１のうち空調ユニット５に対し車両上下方向の下側で且つ車両幅方向の中央側となる部位に空間部Ｓを画成させ、この空間部Ｓに空調機能以外の機能を有する機器を配置する。 - 特許庁

A receiving section 107 receives the data packet, a recovering section 108 recovers the data of n horizontal lines, a storage section 109 stores that data, and a display section 110 gives an instruction to display the n full-width horizontal lines by scanning based on the stored content.例文帳に追加

受信部１０７がデータパケットを受信し、復元部１０８がｎ本の水平ラインのデータを復元し、記憶部１０９がそれを記憶し、表示部１１０は記憶内容に基づいてｎ本の全幅水平ラインを走査により表示するよう命令する。 - 特許庁

A region in the vicinity of the center of the light entering surface 8 of the light guide plate 4 in its width direction is formed into a rough surface 8A as a high light dispersibility region, and both side regions sandwiching the rough surface 8A is formed into a smooth surface 8B as a low light dispersiblity region.例文帳に追加

導光板４の入射面８における幅方向の中央付近の領域を、高光分散能領域としての粗面８Ａに形成し、粗面８Ａを挟む両側の領域を、低光分散能領域としての平滑面８Ｂに形成した。 - 特許庁

The body member is formed into a cylindrical shape, and the lower part of the body member is bent inward at an inclined angle over the whole periphery with an approximately definite width so as to leave a gap between the inside of the body part and the inside of the lower part to form an annular inclined wall.例文帳に追加

胴部材は筒状に形成し、且つ胴部材の下方部分はほぼ一定巾で全周にわたり、胴部内側と前記下方部分の内側の間に空隙を残す傾斜角度で内方へ折り曲げられて環状傾斜壁が形成されている。 - 特許庁

In this bar-code generation system, a test chart is printed by a printer 200 based on a test chart image 706 for printing a black bar and a white bar for the bar-code respectively with width of the different number of a plurality of dots, and the outputted test chart 704 is read by an image scanner 110.例文帳に追加

バーコード用の黒バーおよび白バーを、それぞれ複数の異なるドット数の幅で印刷するためのテストチャート画像７０６に基づいて、印刷装置２００でテストチャートを印刷し、出力されたテストチャート７０４をイメージスキャナ１１０で読み取る。 - 特許庁

On one end of the plate springs 3 coupled in the coupling holes 22 of the outer frame, nails 33 capable of expanding in the width direction by the bending elasticity are arranged on both sides of the coupling part 32 and both nails 33 are hooked in the coupling holes 22 so that the outer frame and the plate spring are combined.例文帳に追加

外枠２の嵌合穴２２に嵌合される板ばね３の一端には、曲げ弾性により幅方向に展開できる爪３３を嵌合部３２の両側に配し、両爪３３を嵌合穴２２に引っかけて外枠と板ばねとが組み合わされる。 - 特許庁

To save labor for adjusting the top nail of a game machine with a variable display device with comparatively large width almost at the center of the game area and to suppress deviation of passage of falling balls hit in the game area by equipping a sorting means.例文帳に追加

最大横幅が比較的大きな最大横幅を有する可変表示装置を遊技領域のほぼ中央部に有する遊技機の天釘の調整作業を省力化するとともに、遊技領域に打ち込まれた遊技球の落下経路の偏りを抑制する。 - 特許庁

When the detected current value falls in the range between the upper and the lower limit values th1, th2 after execution of the forward control, a reverse control is executed such that a pulse width of a PWM signal S1 (S2) is changed in an adjustment direction opposite to that under the forward control.例文帳に追加

前進制御の実行後に、検出電流値ｉが上限値ｔｈ１及び下限値ｔｈ２の間に入った場合、この前進制御時とは逆の増減方向にＰＷＭ信号Ｓ１（Ｓ２）のパルス幅を変調させる後退制御を実行する。 - 特許庁

To provide a manufacturing apparatus of a thin film laminated member which can maintain with high precision a position in the vertical direction of a substrate, even if the substrate is conveyed over a long distance in the horizontal direction, while the width direction of a band-shaped flexible substrate is oriented toward the vertical direction.例文帳に追加

帯状可撓性基板の幅方向を鉛直方向に向けながら、基板を水平方向に長い距離にわたり搬送しても、基板の鉛直方向における位置を精度高く維持することができる薄膜積層体の製造装置を提供する。 - 特許庁